Home › ENGINE ยท 2TR-FBE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE OIL FILLER CAP SUB-ASSEMBLY
  1. Remove the oil filler cap from the head cover.



2. REMOVE PCV VALVE SUB-ASSEMBLY


    A239739
  1. Loosen the hose clamp and disconnect the PCV hose from the PCV valve sub-assembly.

  1. Remove the PCV valve sub-assembly.



3. REMOVE CYLINDER HEAD COVER


    G035202E05
  1. Remove the 19 bolts, 2 nuts, cover and 2 gaskets.



4. REMOVE CRANKSHAFT PULLEY


G038864E13
  1. Turn the crankshaft pulley, and align its groove with timing mark 0 of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gear and sprocket are aligned with the timing marks of the No. 1 bearing cap, as shown in the illustration.



    A099211E08
  1. Using SST, loosen the pulley bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    G035121E07
  1. Using SST, remove the pulley bolt and pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)



5. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
  1. Remove the drain plug and gasket.



    A099214E02
  1. Remove the 20 bolts and 2 nuts.



    A099215E09
  1. Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the oil pan.

    NOTICE:
    Be careful not to damage the contact surface of the oil pans.



6. REMOVE OIL STRAINER SUB-ASSEMBLY
  1. Remove the bolt, 2 nuts, oil strainer and gasket.



7. REMOVE OIL PAN SUB-ASSEMBLY


    A099220E02
  1. Remove the 16 bolts and 2 nuts.



    G036411E01
  1. Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surface of the cylinder block and oil pan.



    G037271E01
  1. Remove the O-ring.



8. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    G036504E01
  1. Remove the 19 bolts and 2 nuts shown in the illustration.



    G037273E01
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head, cylinder block and timing chain cover.

    HINT:
    Tape the screwdriver tip before use.



    G037274E01
  1. Remove the 3 O-rings.



    G036021E02
  1. Using a 10 mm socket hexagon wrench, remove the timing gear case plug.



9. REMOVE ENGINE WATER PUMP ASSEMBLY


    A087223E03
  1. Remove the 8 bolts, engine water pump and gasket.



10. REMOVE TIMING CHAIN COVER OIL SEAL


    A097898E03
  1. Place the timing chain cover on wooden blocks.

  1. Using a screwdriver with its tip taped, pry out the oil seal.



    A172563E01
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.

    SST
    09223-75010  
    09950-70010   (09951-07150)

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap the oil seal at an angle.

  1. Apply a light coat of MP grease to a new oil seal lip.



11. REMOVE OIL PUMP RELIEF VALVE


    A086864E04
  1. Using a 27 mm socket wrench, remove the plug and gasket.

  1. Remove the valve spring and relief valve.



12. REMOVE TIMING CHAIN GUIDE


    G037278E02
  1. Remove the 2 bolts and chain guide and O-ring.



13. REMOVE NO. 1 TIMING CHAIN TENSIONER


A097899E06

NOTICE:
  1. When the chain tensioner is removed, do not rotate the crankshaft.
  2. When the chain is removed and the camshaft needs to be rotated, rotate the crankshaft 90° to the right.

  1. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.

  1. Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate's hole.



    G039810E01
  1. Remove the bolt, nut, chain tensioner and gasket.



14. REMOVE CHAIN TENSIONER SLIPPER


    G037281E01
  1. Remove the bolt and tensioner slipper.



15. REMOVE NO. 1 VIBRATION DAMPER


    G037280E01
  1. Remove the bolt, nut and vibration damper.



16. REMOVE TIMING CHAIN


17. REMOVE CRANKSHAFT TIMING SPROCKET


    G037282E01
  1. Remove the crankshaft timing sprocket from the crankshaft.



18. REMOVE CAMSHAFT


    A097866E01
  1. Uniformly loosen the 21 bearing cap bolts in the several passes in the order shown in the illustration.

  1. Remove the 9 bearing caps, oil delivery pipe, O-ring and 2 camshafts.

    NOTICE:
    1. Place the camshaft on a flat surface, maintain this position and loosen the bolts uniformly.
    2. Do not pry the camshaft with a tool by applying excessive force to it.
    3. Do not damage the reception part of the exhaust on the cylinder head side.



    G037284E04
  1. Remove the oil delivery pipe and O-ring from the bearing caps.



    G037285E01
  1. Remove the 9 bearing caps.

  1. Remove the 2 camshafts.



19. REMOVE CAMSHAFT TIMING SPROCKET


    A086867E01
  1. Fix the camshaft with a vise, and then remove the sprocket bolt and camshaft timing sprocket.

    NOTICE:
    Be careful not to damage the camshaft.



20. REMOVE CAMSHAFT TIMING GEAR


    A097871E10
  1. Remove the flange bolt of the camshaft timing gear.

    NOTICE:
    1. Be sure not to remove the other 3 bolts.
    2. If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.



21. REMOVE CYLINDER HEAD


    A097901E01
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in an incorrect order.

  1. Remove the cylinder head and gasket.



22. REMOVE NO. 2 CHAIN VIBRATION DAMPER


    G037294E06
  1. Move the stopper plate downward to release the lock, and push the plunger deep into the tensioner.

  1. Move the stopper plate upward to set the lock, and insert a hexagon wrench into the stopper plate's hole.



    G037295E01
  1. Remove the bolt and chain vibration damper.



23. REMOVE NO. 3 CHAIN VIBRATION DAMPER


    G037296E01
  1. Remove the 2 bolts and chain vibration damper.



24. REMOVE NO. 2 CHAIN TENSIONER


    G037297E01
  1. Remove the hexagon wrench from the tensioner.

  1. Remove the nut and chain tensioner.



25. REMOVE NO. 2 CHAIN


    G037298E01
  1. Remove the bolt, balance shaft drive gear shaft and balance shaft drive gear.

  1. Remove the No. 2 crankshaft timing sprocket and chain.



26. REMOVE NO. 4 CHAIN VIBRATION DAMPER


    G037299E01
  1. Remove the 2 bolts and No. 4 vibration damper.



27. REMOVE CRANKSHAFT PULLEY SET KEY


    G037300E01
  1. Remove the 2 pulley set keys from the crankshaft.



28. REMOVE OIL FILTER


    A097902E01
  1. Using SST, remove the oil filter.

    SST
    09228-07501  



29. REMOVE OIL FILTER UNION


    G037462E03
  1. Using a 27 mm socket wrench, remove the oil filter union.



30. REMOVE OIL FILTER BRACKET


    G037304E03
  1. Remove the 2 screw plugs and 2 gaskets from the oil filter bracket.

  1. Remove the 2 bolts, nut and oil filter bracket.



    G037305E04
  1. Remove the gasket and O-ring.



    A249302
  1. Using a 14 mm hexagon wrench, remove the oil filter bracket union.



31. REMOVE ENGINE REAR OIL SEAL RETAINER
  1. Remove the 6 bolts.



    A097903E01
  1. Using a screwdriver with its tip taped, pry out the oil seal retainer.



32. REMOVE VALVE ROCKER ARM

HINT:
Each rocker arm must be reinstalled to its original location.



33. REMOVE VALVE STEM CAP

HINT:
Each stem cap must be reinstalled to its original locations.



34. REMOVE VALVE LASH ADJUSTER

HINT:
Each lash adjuster must be reinstalled to its original location.



35. REMOVE INTAKE VALVE


    A097931E01
  1. Using SST and wooden blocks, compress the compression spring and remove the valve retainer locks.

    SST
    09202-70020   (09202-00010)



    A121457E01
  1. Remove the retainer, compression spring, valve, valve spring and spring seat.

    HINT:
    Each intake valve must be reinstalled to its original location.



36. REMOVE EXHAUST VALVE


    A097932E01
  1. Using SST and wooden blocks, compress the compression spring and remove the valve retainer locks.

    SST
    09202-70020   (09202-00010)



    A121461
  1. Remove the retainer, compression spring, valve, valve spring and spring seat.

    HINT:
    Each exhaust valve must be reinstalled to its original location.



37. REMOVE VALVE STEM OIL SEAL


    G037403E01
  1. Using needle-nose pliers, remove the oil seal.



38. REMOVE OIL CONTROL VALVE FILTER


    G037445E01
  1. Using an 8 mm hexagon wrench, remove the screw plug.

  1. Remove the oil control valve filter and gasket.



39. REMOVE NO. 1 STRAIGHT SCREW PLUG


    A097933E05
  1. Using a 10 mm hexagon wrench, remove the 3 screw plugs.



40. REMOVE NO. 2 STRAIGHT SCREW PLUG


    A097934E04
  1. Using a 9 mm hexagon wrench, remove the screw plug.



41. INSPECT CONNECTING ROD THRUST CLEARANCE


    G037344E01
  1. Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

    Standard thrust clearance:
    0.15 to 0.35 mm (0.00591 to 0.0138 in.)

    Maximum thrust clearance:
    0.40 mm (0.0157 in.)

    If the thrust clearance is more than the maximum, replace the connecting rod assembly(s). If necessary, replace the crankshaft.



42. INSPECT CONNECTING ROD OIL CLEARANCE


    A097980E03
  1. Check that the front mark on the connecting rod and cap are aligned to ensure the correct reassembly.

    HINT:
    The front mark on the connecting rods and caps are for ensuring the correct reassembly.



    G037345E01
  1. Remove the 2 connecting rod cap bolts.

  1. Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.

    HINT:
    Keep the lower bearing inserted to the connecting rod cap.

  1. Clean the crank pin and bearing.

  1. Check the crank pin and bearing for pitting and scratches.



    G037346E02
  1. Lay a strip of Plastigage on the crank pin.



  1. Install the connecting rod cap.

    NOTICE:
    Do not turn the crankshaft.


    1. Match the numbered connecting rod cap with the connecting rod.

    2. Align the pins of the connecting rod cap with the pin holes of the connecting rod, and install the connecting rod cap.



    3. G037347E01
    4. Check that the front mark of the connecting rod cap is facing forward.



  1. Install the connecting rod cap bolts.

    HINT:
    1. The connecting rod cap bolts are tightened in 2 progressive steps.
    2. If any connecting rod bolt is broken or deformed, replace it.


    1. Apply a light coat of engine oil on the threads and under the heads of the connecting rod cap bolts.

    2. Install and alternately tighten the bolts of the connecting rod cap in several passes.

      Torque:
      25 N*m{ 250 kgf*cm , 18 ft.*lbf }

      If any one of the connecting rod cap bolts does not meet the torque specification, replace the cap bolts.



    3. A099641E05
    4. Mark the front of the connecting rod cap bolts with paint.

    5. Retighten the connecting rod cap bolts 90° as shown.

    6. Check that the painted mark is now at a 90° angle to the front.

  1. Remove the 2 bolts and connecting rod cap.



    G039628E01
  1. Measure the Plastigage at its widest point.

    Standard oil clearance:
    0.039 to 0.066 mm (0.00154 to 0.00260 in.)
    Maximum oil clearance:
    0.066 mm (0.00260 in.)

    If the crank pin or bearing is damaged, replace the bearings. If necessary, replace the crankshaft.

    HINT:
    If replacing a bearing, replace it with one that has the same number as its respective connecting rod cap. Each bearing's standard thickness is indicated by a 4, 5 or 6 mark on its surface.

    Standard bearing center wall thickness:
    Mark
    Specified Condition
    4
    1.484 to 1.487 mm (0.05843 to 0.05854 in.)
    5
    1.488 to 1.490 mm (0.05858 to 0.05866 in.)
    6
    1.491 to 1.493 mm (0.05870 to 0.05878 in.)

  1. Completely remove the Plastigage.



43. REMOVE PISTON WITH CONNECTING ROD


    G035191E03
  1. Using a ridge reamer, remove all the carbon from the top of the cylinder.

  1. Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

    HINT:
    1. Keep the bearing, connecting rod and cap together.
    2. Arrange the piston and connecting rod assemblies in the correct order.



44. INSPECT CRANKSHAFT THRUST CLEARANCE


    G037352E01
  1. Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

    Standard thrust clearance:
    0.02 to 0.22 mm (0.000787 to 0.00866 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is more than the maximum, replace the thrust washers as a set.

    Thrust washer thickness:
    2.440 to 2.490 mm (0.0961 to 0.0980 in.)



45. INSPECT CRANKSHAFT OIL CLEARANCE


HINT:
Before performing this procedure, make sure to check the procedure selection chart, as there are different types of crankshafts and cylinder blocks.

NOTICE:
Only perform the procedure for type C when there are letters for the cylinder block journal code and there is a crankshaft journal code.



A346115E01


Text in Illustration 
*a
Cylinder Block Journal Code
*b
Crankshaft Journal Code

Procedure Selection Chart 
-
No Journal Code on Crankshaft
Journal Code on Crankshaft
Cylinder Block Journal Code (Numbers)
Type A
Type A
Cylinder Block Journal Code (Letters)
Type B
Type C


    A097951E03
  1. Uniformly loosen the 10 bearing cap bolts in several passes in the sequence shown in the illustration.

    HINT:
    1. Keep the lower bearings and crankshaft bearing caps together.
    2. Arrange the thrust washers in the correct order.

  1. Clean each main journal and bearing.

  1. Check each main journal and bearing for pitting and scratches.
    If the journal or bearing is damaged, replace the bearings. If necessary, grind or replace the crankshaft.

  1. Place the crankshaft on the cylinder block.



    G037376E01
  1. Lay a strip of Plastigage across each journal.



    G037377E01
  1. Install the 5 crankshaft bearing caps in their proper locations.

    NOTICE:
    Do not turn the crankshaft.



    A097951E01
  1. Install the crankshaft bearing cap bolts.

    HINT:
    1. The main bearing cap bolts are tightened in 2 progressive steps.
    2. If any of the main bearing cap bolts are broken or deformed, replace as necessary.


    1. Install and uniformly tighten the 10 main bearing cap bolts in the sequence shown in the illustration.

      Torque:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }

      If any one of the main bearing cap bolts does not meet the torque specification, replace the main bearing cap bolt.



    2. A099641E05
    3. Mark the front of the bearing cap bolts with paint.

    4. Retighten the bearing cap bolts by 90° in the numerical order above.

    5. Check that the painted mark is now at a 90° angle to the front.

  1. Remove the 10 bolts and 5 crankshaft bearing caps.



  1. Check the type of crankshaft journal code and cylinder block journal code and select an inspection procedure.


    A346115E01


    Text in Illustration 
    *a
    Cylinder Block Journal Code
    *b
    Crankshaft Journal Code

    Procedure Selection Chart 
    -
    No Journal Code on Crankshaft
    Journal Code on Crankshaft
    Cylinder Block Journal Code (Numbers)
    Type A
    Type A
    Cylinder Block Journal Code (Letters)
    Type B
    Type C

    NOTICE:
    Only perform the procedure for type C when there are letters for the cylinder block journal code and there is a crankshaft journal code.



  1. for Type A:



      G039585E04
    1. Measure the Plastigage at its widest point.

      Standard Oil Clearance:
      Item
      Specified Condition
      No. 3 journal
      0.030 to 0.055 mm (0.0012 to 0.0022 in.)
      Other journal
      0.024 to 0.049 mm (0.0009 to 0.0019 in.)

      Maximum oil clearance:
      0.10 mm (0.0039 in.)

      If the oil clearance is more than the maximum, replace the crankshaft bearing.
      If replacing the cylinder block, measure the bearing standard clearance.
      If replacing a bearing, first check the number on the cylinder block for the bearing's respective journal. Then replace the bearing with one that has the same number. Each bearing's standard thickness is indicated by a 1, 2 or 3 mark on its surface.

      Cylinder Block Main Journal Bore Diameter:
      Item
      Specified Condition
      Mark 1
      64.004 to 64.010 mm (2.5198 to 2.5201 in.)
      Mark 2
      64.011 to 64.016 mm (2.5201 to 2.5203 in.)
      Mark 3
      64.017 to 64.022 mm (2.5203 to 2.5206 in.)

      Standard Bearing Center Wall Thickness:
      Item
      Specified Condition
      Mark 1
      1.987 to 1.990 mm (0.07823 to 0.07835 in.)
      Mark 2
      1.991 to 1.993 mm (0.07839 to 0.07846 in.)
      Mark 3
      1.994 to 1.996 mm (0.07850 to 0.07858 in.)



  1. for Type B:



    1. Measure the Plastigage at its widest point.


      A337686E01


      Text in Illustration 
      *a
      Plastigage
      *b
      No. 1 Journal
      *c
      No. 2 Journal
      *d
      No. 3 Journal
      *e
      No. 4 Journal
      *f
      No. 5 Journal
      *g
      Cylinder Block Journal Code
      *h
      Crankshaft Bearing Code
      *i
      Bearing Code Chart
      -
      -

      Standard Oil Clearance:
      Item
      Specified Condition
      No. 3 journal
      0.030 to 0.055 mm (0.0012 to 0.0022 in.)
      Other journal
      0.024 to 0.049 mm (0.0009 to 0.0019 in.)

      Maximum oil clearance:
      0.10 mm (0.0039 in.)

      If the oil clearance is more than the maximum, replace the crankshaft bearing.
      If replacing the cylinder block, measure the bearing standard clearance.
      Check the cylinder block journal code and refer to the crankshaft bearing selection chart to select a bearing size.
      (Example): When the cylinder block journal code is "D", select crankshaft bearing selection code "2" from the crankshaft bearing selection chart.

      Cylinder Block Main Journal Bore Diameter:

      Item
      Specified Condition
      Mark A
      64.004 to 64.006 mm (2.51984 to 2.51992 in.)
      Mark B
      64.007 to 64.008 mm (2.51996 to 2.51999 in.)
      Mark C
      64.009 to 64.010 mm (2.52003 to 2.52007 in.)
      Mark D
      64.011 to 64.012 mm (2.52011 to 2.52015 in.)
      Mark E
      64.013 to 64.014 mm (2.52019 to 2.52023 in.)
      Mark F
      64.015 to 64.016 mm (2.52027 to 2.52031 in.)
      Mark G
      64.017 to 64.018 mm (2.52035 to 2.52039 in.)
      Mark H
      64.019 to 64.020 mm (2.52043 to 2.52047 in.)
      Mark J
      64.021 to 64.022 mm (2.52051 to 2.52055 in.)


      Standard Bearing Center Wall Thickness:

      Item
      Specified Condition
      Mark 1
      1.987 to 1.990 mm (0.07823 to 0.07835 in.)
      Mark 2
      1.991 to 1.993 mm (0.07839 to 0.07846 in.)
      Mark 3
      1.994 to 1.996 mm (0.07850 to 0.07858 in.)



  1. for Type C:



    1. Measure the Plastigage at its widest point.


      A337687E01


      Text in Illustration 
      *a
      Plastigage
      *b
      No. 1 Journal
      *c
      No. 2 Journal
      *d
      No. 3 Journal
      *e
      No. 4 Journal
      *f
      No. 5 Journal
      *g
      Crankshaft Bearing Code
      *h
      Cylinder Block Journal Code
      *i
      Crankshaft Journal Code
      *j
      #1J, #2J, #4J, #5J
      *k
      #3J
      *l
      Bearing Code Chart

      Standard Oil Clearance:
      Item
      Specified Condition
      No. 3 journal
      0.030 to 0.044 mm (0.00118 to 0.00173 in.)
      Other journal
      0.024 to 0.038 mm (0.000945 to 0.00150 in.)

      Maximum oil clearance:
      0.10 mm (0.0039 in.)

      If the oil clearance is more than the maximum, replace the crankshaft bearing.
      If replacing the cylinder block, measure the bearing standard clearance.
      Check the cylinder block journal code and crankshaft journal code and refer to the crankshaft bearing selection chart to select a bearing size.
      (Example) (Excluding No. 3 journal): When the cylinder block journal code is "D" and the crankshaft journal code is "4", select crankshaft bearing selection code "3" from the crankshaft bearing selection chart.

      Cylinder Block Main Journal Bore Diameter:

      Item
      Specified Condition
      Mark A
      64.004 to 64.006 mm (2.51984 to 2.51992 in.)
      Mark B
      64.007 to 64.008 mm (2.51996 to 2.51999 in.)
      Mark C
      64.009 to 64.010 mm (2.52003 to 2.52007 in.)
      Mark D
      64.011 to 64.012 mm (2.52011 to 2.52015 in.)
      Mark E
      64.013 to 64.014 mm (2.52019 to 2.52023 in.)
      Mark F
      64.015 to 64.016 mm (2.52027 to 2.52031 in.)
      Mark G
      64.017 to 64.018 mm (2.52035 to 2.52039 in.)
      Mark H
      64.019 to 64.020 mm (2.52043 to 2.52047 in.)
      Mark J
      64.021 to 64.022 mm (2.52051 to 2.52055 in.)


      Crankshaft Journal Bore Diameter:

      Item
      Specified Condition (Other Journal)
      Specified Condition (No. 3 Journal)
      Mark 0
      59.999 to 60.000 mm (2.36216 to 2.36220 in.)
      -
      Mark 1
      59.997 to 59.998 mm (2.36208 to 2.36212 in.)
      -
      Mark 2
      59.995 to 59.996 mm (2.36200 to 2.36204 in.)
      -
      Mark 3
      59.993 to 59.994 mm (2.36192 to 2.36196 in.)
      59.993 to 59.994 mm (2.36192 to 2.36196 in.)
      Mark 4
      59.991 to 59.992 mm (2.36185 to 2.36189 in.)
      59.991 to 59.992 mm (2.36185 to 2.36189 in.)
      Mark 5
      59.989 to 59.990 mm (2.36177 to 2.36181 in.)
      59.989 to 59.990 mm (2.36177 to 2.36181 in.)
      Mark 6
      59.987 to 59.988 mm (2.36169 to 2.36173 in.)
      59.987 to 59.988 mm (2.36169 to 2.36173 in.)
      Mark 7
      -
      59.985 to 59.986 mm (2.36161 to 2.36165 in.)
      Mark 8
      -
      59.983 to 59.984 mm (2.36153 to 2.36157 in.)
      Mark 9
      -
      59.981 to 59.982 mm (2.36145 to 2.36149 in.)


      Standard Bearing Center Wall Thickness:

      Item
      Specified Condition
      Mark 1
      1.987 to 1.990 mm (0.07823 to 0.07835 in.)
      Mark 2
      1.991 to 1.993 mm (0.07839 to 0.07846 in.)
      Mark 3
      1.994 to 1.996 mm (0.07850 to 0.07858 in.)
      Mark 4
      1.997 to 1.999 mm (0.07862 to 0.07870 in.)
      Mark 5
      2.000 to 2.002 mm (0.07874 to 0.07882 in.)

  1. Completely remove the Plastigage.



46. REMOVE CRANKSHAFT
  1. Lift out the crankshaft.

    HINT:
    Keep the upper crankshaft bearings and upper thrust washers together with the cylinder block.



47. REMOVE PISTON WITH PIN


    G035197E02
  1. Check fit between the piston and piston pin.

    1. Try to move the piston back and forth on the piston pin.
      If any movement is felt, replace the piston and pin as a set.



    A239762
  1. Remove the piston rings.

    1. Using a piston ring expander, remove the 2 compression rings.

    2. Remove the rail and expander by hand.

      HINT:
      Arrange the piston rings in the correct order only.



    G035729E01
  1. Disconnect the connecting rod from the piston.

    1. Using a small screwdriver, pry off the snap ring from the piston.

    2. Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).



    3. G036556E01
    4. Using a brass bar and plastic-faced hammer, lightly tap out the piston pin and remove the connecting rod.

      HINT:
      1. The piston and pin are a matched set.
      2. Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.



48. REMOVE CYLINDER BLOCK WATER DRAIN COCK


49. REMOVE OIL NOZZLE


    G037357E01
  1. Using a 5 mm hexagon wrench, remove the oil nozzle.



50. INSPECT BALANCE SHAFT THRUST CLEARANCE


    G037388E01
  1. Using a dial indicator, measure the thrust clearance while moving the balance shaft back and forth.

    Standard thrust clearance:
    0.07 to 0.13 mm (0.00276 to 0.00512 in.)

    Maximum thrust clearance:
    0.20 mm (0.00787 in)

    If the thrust clearance is more than the maximum, replace the balance shaft thrust washer. If necessary, replace the balance shaft.



51. REMOVE NO. 1 BALANCE SHAFT


    G037389E01
  1. Remove the bolt.



    G037390E01
  1. Remove the balance shaft from the cylinder block.

    NOTICE:
    When removing the balance shaft, make sure to support the balance shaft with both hands and avoid scratching the balance shaft bearing on the cylinder block side.



52. REMOVE NO. 1 BALANCE SHAFT DRIVEN GEAR


    G037391E01
  1. Mount the head portion of the balance shaft in a vise.

    NOTICE:
    Be careful not to damage the balance shaft.

  1. Remove the bolt.

  1. Remove the No. 1 balance shaft driven gear (A), sliding key (B), No. 1 balance shaft thrust washer (C) and balance shaft thrust spacer (D).



53. REMOVE NO. 2 BALANCE SHAFT


    G037392E01
  1. Remove the 2 bolts.



    G037393E01
  1. Remove the balance shaft from the cylinder block.

    NOTICE:
    When removing the balance shaft, make sure to support the balance shaft with both hands and avoid scratching the balance shaft bearing on the cylinder block side.



54. REMOVE NO. 2 BALANCE SHAFT DRIVEN GEAR


    G037394E01
  1. Mount the head portion of the balance shaft in a vise.

    NOTICE:
    Be careful not to damage the balance shaft.

  1. Remove the bolt.

  1. Remove the No. 2 balance shaft driven gear (A) and No. 2 balance shaft thrust washer (B).