DTC B1800/51 Short in Driver Side Squib Circuit |
DTC B1801/51 Open in Driver Side Squib Circuit |
DTC B1802/51 Short to GND in Driver Side Squib Circuit |
DTC B1803/51 Short to B+ in Driver Side Squib Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1800/51 | Center airbag sensor assembly receives line short circuit signal 5 times in driver squib circuit during primary check |
|
| B1801/51 | Center airbag sensor assembly receives open circuit signal in driver squib circuit for 2 seconds |
|
| B1802/51 | Center airbag sensor assembly receives short circuit to ground signal in driver squib circuit for 0.5 seconds |
|
| B1803/51 | Center airbag sensor assembly receives B+ short circuit signal in driver squib circuit for 0.5 seconds |
|

| 1.CHECK STEERING PAD (DRIVER SQUIB) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the steering pad (driver squib).
Connect the white wire side of SST (resistance 2.1 Ω) to the spiral cable connector E.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST (resistance 2.1 Ω) from the spiral cable.
Check that the spiral cable connector (on the steering pad side) is not damaged.
|
| ||||
| OK | |
| 3.CHECK DRIVER SQUIB CIRCUIT |
![]() |
Disconnect the connector from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| D+ - Body ground | Below 1 V |
| D- - Body ground | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| D+ - D- | Below 1 Ω |
| D+ - Body ground | 1 MΩ or higher |
| D- - Body ground | 1 MΩ or higher |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| D+ - D- | 1 MΩ or higher |
|
| ||||
| NG | |
| 4.CHECK INSTRUMENT PANEL WIRE |
![]() |
Restore the released activation prevention mechanism of connector B to its original position.
Disconnect the instrument panel wire connector from the spiral cable.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| A26-1 (D+) - Body ground | Below 1 V |
| A26-2 (D-) - Body ground | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| A26-1 (D+) - A26-2 (D-) | Below 1 Ω |
| A26-1 (D+) - Body ground | 1 MΩ or higher |
| A26-2 (D-) - Body ground | 1 MΩ or higher |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| A26-1 (D+) - A26-2 (D-) | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||