Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK TRANSPONDER KEY AMPLIFIER

B085900E01

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T20-7 (AGND) - Body ground
    L-O - Body ground
    Ground
    Always
    Below 1 Ω
    T20-1 (VC5) - T20-7 (AGND)
    L - L-O
    Power source
    No key in ignition key cylinder
    Below 1 V
    Key inserted
    4.6 to 5.4 V
    T20-4 (CODE) - T20-7 (AGND)
    L-Y - L-O
    Demodulated signal of key code data
    No key in ignition key cylinder
    Below 1 V
    Key inserted
    Pulse generation (See waveform 1)
    T20-5 (TXCT) - T20-7 (AGND)
    L-B - L-O
    Key code output signal
    No key in ignition key cylinder
    Below 1 V
    Key inserted
    Pulse generation (See waveform 2)



  2. Inspect using an oscilloscope.



      B086388E04
    1. Waveform 1 (Reference)
      Item
      Content
      Terminal No. (Symbol)
      T20-4 (CODE) - T20-7 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Key inserted



    2. B086389E03
    3. Waveform 2 (Reference)
      Item
      Content
      Terminal No. (Symbol)
      T20-5 (TXCT) - T20-7 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Key inserted


CHECK TRANSPONDER KEY ECU ASSEMBLY


    B276309E03
  1. Disconnect the T21 transponder key ECU assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T21-16 (GND) - Body ground
    G - Body ground
    Ground
    Always
    Below 1 Ω
    T21-1 (+B) - T21-16 (GND)
    L-Y - G
    Power source supply
    Always
    11 to 14 V
    T21-2 (IG) - T21-16 (GND)
    B-O - G
    Ignition power supply
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    11 to 14 V
    T21-3 (KSW) - T21-16 (GND)
    BR - G
    Unlock warning switch
    No key in ignition key cylinder
    10 kΩ or higher
    Key inserted
    Below 1 Ω

  3. Reconnect the T21 transponder key ECU assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T21-14 (VC5) - T21-5 (AGND)
    L - L-O
    Power source of transponder key amplifier
    No key in ignition key cylinder
    Below 1 V
    Key is inserted
    4.6 to 5.4 V
    T21-15 (CODE) - T21-5 (AGND)
    L-Y - L-O
    Transponder key amplifier communication signal
    No key in ignition key cylinder
    Below 1 V
    Key is inserted
    Pulse generation (See waveform 1)
    T21-4 (TXCT) - T21-5 (AGND)
    L-B - L-O
    Transponder key amplifier communication signal
    No key in ignition key cylinder
    Below 1 V
    Key is inserted
    Pulse generation (See waveform 2)
    T21-12 (EFII) - T21-16 (GND)
    Y-B - G
    Transponder key ECU assembly output signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Pulse generation (See waveform 3)
    T21-13 (EFIO) - T21-16 (GND)
    Y-G - G
    Transponder key ECU assembly input signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Pulse generation (See waveform 4)



  5. B086388E04
  6. Using an oscilloscope, check waveform 1.
    Item
    Content
    Terminal No. (Symbol)
    T21-15 (CODE) - T21-5 (AGND)
    Tool Setting
    2 V/DIV., 20 ms./DIV.
    Condition
    Key inserted



  7. B086389E03
  8. Using an oscilloscope, check waveform 2.
    Item
    Content
    Terminal No. (Symbol)
    T21-4 (TXCT) - T21-5 (AGND)
    Tool Setting
    2 V/DIV., 20 ms./DIV
    Condition
    Key inserted



  9. B241926E01
  10. Using an oscilloscope, check waveform 3.
    Item
    Content
    Terminal No. (Symbol)
    T21-12 (EFII) - T21-16 (GND)
    Tool Setting
    5 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.



  11. B069241E20
  12. Using an oscilloscope, check waveform 4.
    Item
    Content
    Terminal No. (Symbol)
    T21-13 (EFIO) - T21-16 (GND)
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON


CHECK ECM (for 2TR-FE)

G035135E01

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E9-15 (IMO) - Body ground
    Y-B -Body ground
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Pulse generation (See waveform 1)
    E9-16 (IMI) - Body ground
    Y-G - Body ground
    ECM output signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Pulse generation (See waveform 2)



  2. B241926E01
  3. Using an oscilloscope, check waveform 1.
    Item
    Content
    Terminal No. (Symbol)
    E9-15 (IMO) - Body ground
    Tool Setting
    5 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.



  4. B069241E20
  5. Using an oscilloscope, check waveform 2.
    Item
    Content
    Terminal No. (Symbol)
    E9-16 (IMI) - Body ground
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON


CHECK ECM (for 1GR-FE)

G036662E05

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E13-15 (IMO) - Body ground
    Y-B -Body ground
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Pulse generation (See waveform 1)
    E13-16 (IMI) - Body ground
    Y-G - Body ground
    ECM output signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Pulse generation (See waveform 2)



  2. B241926E01
  3. Using an oscilloscope, check waveform 1.
    Item
    Content
    Terminal No. (Symbol)
    E13-15 (IMO) - Body ground
    Tool Setting
    5 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.



  4. B069241E20
  5. Using an oscilloscope, check waveform 2.
    Item
    Content
    Terminal No. (Symbol)
    E13-16 (IMI) - Body ground
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON


CHECK ECM (for 2TR-FBE)

B286952E03

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E25-32 (IMO) - Body ground
    Y-B -Body ground
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Pulse generation (See waveform 1)
    E25-31 (IMI) - Body ground
    Y-G - Body ground
    ECM output signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Pulse generation (See waveform 2)



  2. B241926E01
  3. Using an oscilloscope, check waveform 1.
    Item
    Content
    Terminal No. (Symbol)
    E25-32 (IMO) - Body ground
    Tool Setting
    5 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.



  4. B069241E20
  5. Using an oscilloscope, check waveform 2.
    Item
    Content
    Terminal No. (Symbol)
    E25-31 (IMI) - Body ground
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON


CHECK ECM (for 1KD-FTV [except i-ART])

B236632E02

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E5-29 (IMO) - Body ground
    Y-B -Body ground
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Pulse generation (See waveform 1)
    E5-30 (IMI) - Body ground
    Y-G - Body ground
    ECM output signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Pulse generation (See waveform 2)



  2. B241926E01
  3. Using an oscilloscope, check waveform 1.
    Item
    Content
    Terminal No. (Symbol)
    E5-29 (IMO) - Body ground
    Tool Setting
    5 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.



  4. B069241E20
  5. Using an oscilloscope, check waveform 2.
    Item
    Content
    Terminal No. (Symbol)
    E5-30 (IMI) - Body ground
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON


CHECK ECM (for 1KD-FTV [for i-ART])

B286952E04

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E31-29 (IMO) - Body ground
    Y-B -Body ground
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Pulse generation (See waveform 1)
    E31-28 (IMI) - Body ground
    Y-G - Body ground
    ECM output signal
    Ignition switch OFF
    Below 1 V
    Ignition switch ON
    Pulse generation (See waveform 2)



  2. B241926E01
  3. Using an oscilloscope, check waveform 1.
    Item
    Content
    Terminal No. (Symbol)
    E31-29 (IMO) - Body ground
    Tool Setting
    5 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.



  4. B069241E20
  5. Using an oscilloscope, check waveform 2.
    Item
    Content
    Terminal No. (Symbol)
    E31-28 (IMI) - Body ground
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON


CHECK TELEPHONE TRANSCEIVER ASSEMBLY (w/ Blocking System)

B236628E02

  1. Disconnect the T31 telephone transceiver assembly connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T31-6 (IG2) - T31-9 (E)
    B-O - W-B
    Ignition switch
    Ignition switch ON
    11 to 14 V
    T31-9 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    T31-12 (+B) - T31-9 (E)
    L-Y - W-B
    Power supply
    Always
    11 to 14 V

  3. Reconnect the T31 telephone transceiver assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T31-1 (BLK1) - T31-9 (E)
    Y-B - W-B
    Transponder key ECU assembly output signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Pulse generation (See waveform 1)
    T31-2 (BLK4) - T31-9 (E)
    Y-G - W-B
    Transponder key ECU assembly input signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Pulse generation (See waveform 2)
    T31-7 (BLK2) - T31-9 (E)
    Y-B - W-B
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Pulse generation (See waveform 1)
    T31-8 (BLK3) - T31-9 (E)
    Y-G - W-B
    ECM output signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Pulse generation (See waveform 2)



  5. B241926E01
  6. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Tester Connection
    1. T31-1 (BLK1) - T31-9 (E)
    2. T31-7 (BLK2) - T31-9 (E)
    Tool Setting
    5 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.



  7. B069241E20
  8. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Tester Connection
    1. T31-2 (BLK4) - T31-9 (E)
    2. T31-8 (BLK3) - T31-9 (E)
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON