ENGINE IMMOBILISER SYSTEM > TERMINALS OF ECU |
| CHECK TRANSPONDER KEY AMPLIFIER |

Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| T20-7 (AGND) - Body ground | L-O - Body ground | Ground | Always | Below 1 Ω |
| T20-1 (VC5) - T20-7 (AGND) | L - L-O | Power source | No key in ignition key cylinder | Below 1 V |
| Key inserted | 4.6 to 5.4 V | |||
| T20-4 (CODE) - T20-7 (AGND) | L-Y - L-O | Demodulated signal of key code data | No key in ignition key cylinder | Below 1 V |
| Key inserted | Pulse generation (See waveform 1) | |||
| T20-5 (TXCT) - T20-7 (AGND) | L-B - L-O | Key code output signal | No key in ignition key cylinder | Below 1 V |
| Key inserted | Pulse generation (See waveform 2) |
![]() |
Using an oscilloscope, check waveform 1.
| Item | Content |
| Terminal No. (Symbol) | T20-4 (CODE) - T20-7 (AGND) |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Key inserted |
![]() |
Using an oscilloscope, check waveform 2.
| Item | Content |
| Terminal No. (Symbol) | T20-5 (TXCT) - T20-7 (AGND) |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Key inserted |
| CHECK TRANSPONDER KEY ECU ASSEMBLY |
![]() |
Disconnect the T21 transponder key ECU assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| T21-16 (GND) - Body ground | G - Body ground | Ground | Always | Below 1 Ω |
| T21-1 (+B) - T21-16 (GND) | L-Y - G | Power source supply | Always | 11 to 14 V |
| T21-2 (IG) - T21-16 (GND) | B-O - G | Ignition power supply | Ignition switch OFF | Below 1 V |
| Ignition switch ON | 11 to 14 V | |||
| T21-3 (KSW) - T21-16 (GND) | BR - G | Unlock warning switch | No key in ignition key cylinder | 10 kΩ or higher |
| Key inserted | Below 1 Ω |
Reconnect the T21 transponder key ECU assembly connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| T21-14 (VC5) - T21-5 (AGND) | L - L-O | Power source of transponder key amplifier | No key in ignition key cylinder | Below 1 V |
| Key is inserted | 4.6 to 5.4 V | |||
| T21-15 (CODE) - T21-5 (AGND) | L-Y - L-O | Transponder key amplifier communication signal | No key in ignition key cylinder | Below 1 V |
| Key is inserted | Pulse generation (See waveform 1) | |||
| T21-4 (TXCT) - T21-5 (AGND) | L-B - L-O | Transponder key amplifier communication signal | No key in ignition key cylinder | Below 1 V |
| Key is inserted | Pulse generation (See waveform 2) | |||
| T21-12 (EFII) - T21-16 (GND) | Y-B - G | Transponder key ECU assembly output signal | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. | Pulse generation (See waveform 3) |
| T21-13 (EFIO) - T21-16 (GND) | Y-G - G | Transponder key ECU assembly input signal | Ignition switch OFF | Below 1 V |
| Ignition switch ON | Pulse generation (See waveform 4) |
![]() |
Using an oscilloscope, check waveform 1.
| Item | Content |
| Terminal No. (Symbol) | T21-15 (CODE) - T21-5 (AGND) |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Key inserted |
![]() |
Using an oscilloscope, check waveform 2.
| Item | Content |
| Terminal No. (Symbol) | T21-4 (TXCT) - T21-5 (AGND) |
| Tool Setting | 2 V/DIV., 20 ms./DIV |
| Condition | Key inserted |
![]() |
Using an oscilloscope, check waveform 3.
| Item | Content |
| Terminal No. (Symbol) | T21-12 (EFII) - T21-16 (GND) |
| Tool Setting | 5 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. |
![]() |
Using an oscilloscope, check waveform 4.
| Item | Content |
| Terminal No. (Symbol) | T21-13 (EFIO) - T21-16 (GND) |
| Tool Setting | 10 V/DIV., 100 ms./DIV. |
| Condition | Ignition switch ON |
| CHECK ECM (for 2TR-FE) |

Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E9-15 (IMO) - Body ground | Y-B -Body ground | ECM input signal | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. | Pulse generation (See waveform 1) |
| E9-16 (IMI) - Body ground | Y-G - Body ground | ECM output signal | Ignition switch OFF | Below 1 V |
| Ignition switch ON | Pulse generation (See waveform 2) |
![]() |
Using an oscilloscope, check waveform 1.
| Item | Content |
| Terminal No. (Symbol) | E9-15 (IMO) - Body ground |
| Tool Setting | 5 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. |
![]() |
Using an oscilloscope, check waveform 2.
| Item | Content |
| Terminal No. (Symbol) | E9-16 (IMI) - Body ground |
| Tool Setting | 10 V/DIV., 100 ms./DIV. |
| Condition | Ignition switch ON |
| CHECK ECM (for 1GR-FE) |

Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E13-15 (IMO) - Body ground | Y-B -Body ground | ECM input signal | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. | Pulse generation (See waveform 1) |
| E13-16 (IMI) - Body ground | Y-G - Body ground | ECM output signal | Ignition switch OFF | Below 1 V |
| Ignition switch ON | Pulse generation (See waveform 2) |
![]() |
Using an oscilloscope, check waveform 1.
| Item | Content |
| Terminal No. (Symbol) | E13-15 (IMO) - Body ground |
| Tool Setting | 5 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. |
![]() |
Using an oscilloscope, check waveform 2.
| Item | Content |
| Terminal No. (Symbol) | E13-16 (IMI) - Body ground |
| Tool Setting | 10 V/DIV., 100 ms./DIV. |
| Condition | Ignition switch ON |
| CHECK ECM (for 2TR-FBE) |

Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E25-32 (IMO) - Body ground | Y-B -Body ground | ECM input signal | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. | Pulse generation (See waveform 1) |
| E25-31 (IMI) - Body ground | Y-G - Body ground | ECM output signal | Ignition switch OFF | Below 1 V |
| Ignition switch ON | Pulse generation (See waveform 2) |
![]() |
Using an oscilloscope, check waveform 1.
| Item | Content |
| Terminal No. (Symbol) | E25-32 (IMO) - Body ground |
| Tool Setting | 5 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. |
![]() |
Using an oscilloscope, check waveform 2.
| Item | Content |
| Terminal No. (Symbol) | E25-31 (IMI) - Body ground |
| Tool Setting | 10 V/DIV., 100 ms./DIV. |
| Condition | Ignition switch ON |
| CHECK ECM (for 1KD-FTV [except i-ART], 2KD-FTV) |

Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E5-29 (IMO) - Body ground | Y-B -Body ground | ECM input signal | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. | Pulse generation (See waveform 1) |
| E5-30 (IMI) - Body ground | Y-G - Body ground | ECM output signal | Ignition switch OFF | Below 1 V |
| Ignition switch ON | Pulse generation (See waveform 2) |
![]() |
Using an oscilloscope, check waveform 1.
| Item | Content |
| Terminal No. (Symbol) | E5-29 (IMO) - Body ground |
| Tool Setting | 5 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. |
![]() |
Using an oscilloscope, check waveform 2.
| Item | Content |
| Terminal No. (Symbol) | E5-30 (IMI) - Body ground |
| Tool Setting | 10 V/DIV., 100 ms./DIV. |
| Condition | Ignition switch ON |
| CHECK ECM (for 1KD-FTV [for i-ART]) |

Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E31-29 (IMO) - Body ground | Y-B -Body ground | ECM input signal | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. | Pulse generation (See waveform 1) |
| E31-28 (IMI) - Body ground | Y-G - Body ground | ECM output signal | Ignition switch OFF | Below 1 V |
| Ignition switch ON | Pulse generation (See waveform 2) |
![]() |
Using an oscilloscope, check waveform 1.
| Item | Content |
| Terminal No. (Symbol) | E31-29 (IMO) - Body ground |
| Tool Setting | 5 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. |
![]() |
Using an oscilloscope, check waveform 2.
| Item | Content |
| Terminal No. (Symbol) | E31-28 (IMI) - Body ground |
| Tool Setting | 10 V/DIV., 100 ms./DIV. |
| Condition | Ignition switch ON |
| CHECK TELEPHONE TRANSCEIVER ASSEMBLY (w/ Blocking System) |
![]() |
Disconnect the T31 telephone transceiver assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| T31-6 (IG2) - T31-9 (E) | B-O - W-B | Ignition switch | Ignition switch ON | 11 to 14 V |
| T31-9 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| T31-12 (+B) - T31-9 (E) | L-Y - W-B | Power supply | Always | 11 to 14 V |
Reconnect the T31 telephone transceiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| T31-1 (BLK1) - T31-9 (E) | Y-B - W-B | Transponder key ECU assembly output signal | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. | Pulse generation (See waveform 1) |
| T31-2 (BLK4) - T31-9 (E) | Y-G - W-B | Transponder key ECU assembly input signal | Ignition switch off | Below 1 V |
| Ignition switch ON | Pulse generation (See waveform 2) | |||
| T31-7 (BLK2) - T31-9 (E) | Y-B - W-B | ECM input signal | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. | Pulse generation (See waveform 1) |
| T31-8 (BLK3) - T31-9 (E) | Y-G - W-B | ECM output signal | Ignition switch off | Below 1 V |
| Ignition switch ON | Pulse generation (See waveform 2) |
![]() |
Using an oscilloscope, check waveform 1.
| Item | Content |
| Tester Connection |
|
| Tool Setting | 5 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. |
![]() |
Using an oscilloscope, check waveform 2.
| Item | Content |
| Tester Connection |
|
| Tool Setting | 10 V/DIV., 100 ms./DIV. |
| Condition | Ignition switch ON |