Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

DTC    B2799/99    Engine Immobiliser System Malfunction

for Preparation Click here


DESCRIPTION

This DTC is output when one of the following occurs: 1) the ECM detects errors in its own communications with the transponder key ECU assembly ; 2) the ECM detects errors in the communication lines; or 3) the ECU communication ID between the transponder key ECU assembly and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no transponder key ECU assembly DTCs are present. If present, troubleshoot the transponder key ECU assembly DTCs first.

DTC Code
DTC Detection Condition
Trouble Area
B2799/99
One of following conditions is met:
  1. Error in communication between ECM and transponder key ECU
  2. Error in communication lines
  3. Communication ID is different during communication with transponder key ECU
  1. Harness or connector
  2. Transponder key ECU assembly
  3. ECM
  4. Telephone transceiver assembly*
  1. *: w/ Blocking System

WIRING DIAGRAM


B317720E02


B315875E04


INSPECTION PROCEDURE

NOTICE:
When replacing the transponder key ECU assembly, telephone transceiver assembly (w/ Blocking System) or ECM, refer to the Service Bulletin.

HINT:
w/ Blocking System:
  1. When DTC B1587 and B2799/99 are output simultaneously, perform troubleshooting for DTC B2799/99 first.
  2. After troubleshooting for this DTC, make sure B2799/99 is not present. If present, troubleshoot the blocking system DTCs next.

1.CLEAR DTC
  1. Clear the DTCs.


NEXT


2.CHECK FOR DTC
  1. Check for DTCs.

    OK:
    DTC B2799/99 is not output.

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/ Blocking System)
    B
    NG (w/o Blocking System)
    C



B
Go to step 3

C
Go to step 4
A

USE SIMULATION METHOD TO CHECK 

3.CHECK BLOCKING SYSTEM (SETTING)
  1. Check the blocking system setting.

    HINT:
    1. Check with the customer's contacted service provider to determine whether the blocking system is set.
    2. Request that the customer have the service provider unset the blocking system.

    Result 
    Result
    Proceed to
    Blocking system is unset.
    A
    Blocking system is set.
    B



B
Go to step 7
A


4.REREGISTER ECU COMMUNICATION ID
  1. Reregister the ECU - ECM communication ID (Refer to Service Bulletin).


NEXT


5.CLEAR DTC
  1. Clear the DTCs.


NEXT


6.CHECK FOR DTC
  1. Check for DTCs.

    OK:
    DTC B2799/99 is not output.



NG
Go to step 7
OK

END (ECU COMMUNICATION ID IS NOT REGISTERED CORRECTLY) 

7.CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch off.

  1. Check that the connectors are properly connected to the ECM, telephone transceiver assembly* and transponder key ECU assembly.

    1. *: w/ Blocking System

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTOR CORRECTLY
OK


8.CHECK HARNESS AND CONNECTOR (SFI OR ECD COMMUNICATION LINE)
  1. Disconnect the T21 transponder key ECU assembly connector.

  1. Disconnect the E5*1, E9*2, E13*3, E25*4 or E31*5 ECM connector.

    1. *1: for 1KD-FTV (except i-ART), 2KD-FTV
    2. *2: for 2TR-FE
    3. *3: for 1GR-FE
    4. *4: for 2TR-FBE
    5. *5: for 1KD-FTV (for i-ART)

  1. w/ Blocking System:
    Disconnect the T31 telephone transceiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1KD-FTV (except i-ART), 2KD-FTV [w/o Blocking System]:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - E5-30 (IMI)
    Always
    Below 1 Ω
    T21-12 (EFII) - E5-29 (IMO)
    Always
    Below 1 Ω
    T21-13 (EFIO) or E5-30 (IMI) - Body ground
    Always
    10 kΩ or higher
    T21-12 (EFII) or E5-29 (IMO) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (except i-ART), 2KD-FTV [w/ Blocking System]:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - T31-2 (BLK4)
    Always
    Below 1 Ω
    T21-12 (EFII) - T31-1 (BLK1)
    Always
    Below 1 Ω
    T31-8 (BLK3) - E5-30 (IMI)
    Always
    Below 1 Ω
    T31-7 (BLK2) - E5-29 (IMO)
    Always
    Below 1 Ω
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    10 kΩ or higher
    T21-12 (EFII) or T31-1 (BLK1) - Body ground
    Always
    10 kΩ or higher
    T31-8 (BLK3) or E5-30 (IMI) - Body ground
    Always
    10 kΩ or higher
    T31-7 (BLK2) or E5-29 (IMO) - Body ground
    Always
    10 kΩ or higher
    for 2TR-FE (w/o Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - E9-16 (IMI)
    Always
    Below 1 Ω
    T21-12 (EFII) - E9-15 (IMO)
    Always
    Below 1 Ω
    T21-13 (EFIO) or E9-16 (IMI) - Body ground
    Always
    10 kΩ or higher
    T21-12 (EFII) or E9-15 (IMO) - Body ground
    Always
    10 kΩ or higher
    for 2TR-FE (w/ Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - T31-2 (BLK4)
    Always
    Below 1 Ω
    T21-12 (EFII) - T31-1 (BLK1)
    Always
    Below 1 Ω
    T31-8 (BLK3) - E9-16 (IMI)
    Always
    Below 1 Ω
    T31-7 (BLK2) - E9-15 (IMO)
    Always
    Below 1 Ω
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    10 kΩ or higher
    T21-12 (EFII) or T31-1 (BLK1) - Body ground
    Always
    10 kΩ or higher
    T31-8 (BLK3) or E9-16 (IMI) - Body ground
    Always
    10 kΩ or higher
    T31-7 (BLK2) or E9-15 (IMO) - Body ground
    Always
    10 kΩ or higher
    for 1GR-FE (w/o Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - E13-16 (IMI)
    Always
    Below 1 Ω
    T21-12 (EFII) - E13-15 (IMO)
    Always
    Below 1 Ω
    T21-13 (EFIO) or E13-16 (IMO) - Body ground
    Always
    10 kΩ or higher
    T21-12 (EFII) or E13-15 (IMO) - Body ground
    Always
    10 kΩ or higher
    for 1GR-FE (w/ Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - T31-2 (BLK4)
    Always
    Below 1 Ω
    T21-12 (EFII) - T31-1 (BLK1)
    Always
    Below 1 Ω
    T31-8 (BLK3) - E13-16 (IMI)
    Always
    Below 1 Ω
    T31-7 (BLK2) - E13-15 (IMO)
    Always
    Below 1 Ω
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    10 kΩ or higher
    T21-12 (EFII) or T31-1 (BLK1) - Body ground
    Always
    10 kΩ or higher
    T31-8 (BLK3) or E13-16 (IMI) - Body ground
    Always
    10 kΩ or higher
    T31-7 (BLK2) or E13-15 (IMO) - Body ground
    Always
    10 kΩ or higher
    for 2TR-FBE (w/o Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - E25-31 (IMI)
    Always
    Below 1 Ω
    T21-12 (EFII) - E25-32 (IMO)
    Always
    Below 1 Ω
    T21-13 (EFIO) or E25-31 (IMI) - Body ground
    Always
    10 kΩ or higher
    T21-12 (EFII) or E25-32 (IMO) - Body ground
    Always
    10 kΩ or higher
    for 2TR-FBE (w/ Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - T31-2 (BLK4)
    Always
    Below 1 Ω
    T21-12 (EFII) - T31-1 (BLK1)
    Always
    Below 1 Ω
    T31-8 (BLK3) - E25-31 (IMI)
    Always
    Below 1 Ω
    T31-7 (BLK2) - E25-32 (IMO)
    Always
    Below 1 Ω
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    10 kΩ or higher
    T21-12 (EFII) or T31-1 (BLK1) - Body ground
    Always
    10 kΩ or higher
    T31-8 (BLK3) or E25-31 (IMI) - Body ground
    Always
    10 kΩ or higher
    T31-7 (BLK2) or E25-32 (IMO) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (for i-ART) [w/o Blocking System]:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - E31-28 (IMI)
    Always
    Below 1 Ω
    T21-12 (EFII) - E31-29 (IMO)
    Always
    Below 1 Ω
    T21-13 (EFIO) or E31-28 (IMI) - Body ground
    Always
    10 kΩ or higher
    T21-12 (EFII) or E31-29 (IMO) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (for i-ART) [w/ Blocking System]:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - T31-2 (BLK4)
    Always
    Below 1 Ω
    T21-12 (EFII) - T31-1 (BLK1)
    Always
    Below 1 Ω
    T31-8 (BLK3) - E31-28 (IMI)
    Always
    Below 1 Ω
    T31-7 (BLK2) - E31-29 (IMO)
    Always
    Below 1 Ω
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    10 kΩ or higher
    T21-12 (EFII) or T31-1 (BLK1) - Body ground
    Always
    10 kΩ or higher
    T31-8 (BLK3) or E31-28 (IMI) - Body ground
    Always
    10 kΩ or higher
    T31-7 (BLK2) or E31-29 (IMO) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 1KD-FTV (except i-ART), 2KD-FTV [w/o Blocking System]:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or E5-30 (IMI) - Body ground
    Always
    Below 1 V
    T21-12 (EFII) or E5-29 (IMO) - Body ground
    Always
    Below 1 V
    for 1KD-FTV (except i-ART), 2KD-FTV [w/ Blocking System]:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    Below 1 V
    T21-12 (EFII) or T31-1 (BLK1) - Body ground
    Always
    Below 1 V
    T31-8 (BLK3) or E5-30 (IMI) - Body ground
    Always
    Below 1 V
    T31-7 (BLK2) or E5-29 (IMO) - Body ground
    Always
    Below 1 V
    for 2TR-FE (w/o Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or E9-16 (IMI) - Body ground
    Always
    Below 1 V
    T21-12 (EFII) or E9-15 (IMO) - Body ground
    Always
    Below 1 V
    for 2TR-FE (w/ Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    Below 1 V
    T21-12 (EFII) or T31-1 (BLK1) - Body ground
    Always
    Below 1 V
    T31-8 (BLK3) or E9-16 (IMI) - Body ground
    Always
    Below 1 V
    T31-7 (BLK2) or E9-15 (IMO) - Body ground
    Always
    Below 1 V
    for 1GR-FE (w/o Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or E13-16 (IMO) - Body ground
    Always
    Below 1 V
    T21-12 (EFII) or E13-15 (IMO) - Body ground
    Always
    Below 1 V
    for 1GR-FE (w/ Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    Below 1 V
    T21-12 (EFII) or T31-1 (BLK1) - Body ground
    Always
    Below 1 V
    T31-8 (BLK3) or E13-16 (IMI) - Body ground
    Always
    Below 1 V
    T31-7 (BLK2) or E13-15 (IMO) - Body ground
    Always
    Below 1 V
    for 2TR-FBE (w/o Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or E25-31 (IMI) - Body ground
    Always
    Below 1 V
    T21-12 (EFII) or E25-32 (IMO) - Body ground
    Always
    Below 1 V
    for 2TR-FBE (w/ Blocking System):
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    Below 1 V
    T21-12 (EFII) or T31-1 (BLK1) - Body ground
    Always
    Below 1 V
    T31-8 (BLK3) or E25-31 (IMI) - Body ground
    Always
    Below 1 V
    T31-7 (BLK2) or E25-32 (IMO) - Body ground
    Always
    Below 1 V
    for 1KD-FTV (for i-ART) [w/o Blocking System]:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or E31-28 (IMI) - Body ground
    Always
    Below 1 V
    T21-12 (EFII) or E31-29 (IMO) - Body ground
    Always
    Below 1 V
    for 1KD-FTV (for i-ART) [w/ Blocking System]:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or T31-2 (BLK4) - Body ground
    Always
    Below 1 V
    T21-12 (EFII) or T31-1 (BLK1) - Body ground
    Always
    Below 1 V
    T31-8 (BLK3) or E31-28 (IMI) - Body ground
    Always
    Below 1 V
    T31-7 (BLK2) or E31-29 (IMO) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


9.REPLACE ECM
  1. Temporarily replace the ECM assembly with a new one.


NEXT


Go to step 11

10.REREGISTER ECU COMMUNICATION ID
  1. Reregister the ECU - ECM communication ID (Refer to Service Bulletin).


NEXT


11.CLEAR DTC
  1. Clear the DTCs.


NEXT


12.CHECK FOR DTC
  1. Check for DTCs.

    OK:
    DTC B2799/99 is not output.

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/o Blocking System)
    B
    NG (w/ Blocking System)
    C



B
REPLACE TRANSPONDER KEY ECU ASSEMBLY

C
Go to step 13
A

END (ECM IS DEFECTIVE) 

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Temporarily replace the transponder key ECU assembly with a new one (Refer to Service Bulletin).


NEXT


14.REREGISTER ECU COMMUNICATION ID
  1. Reregister the ECU - ECM communication ID (Refer to Service Bulletin).


NEXT


15.CLEAR DTC
  1. Clear the DTCs.


NEXT


16.CHECK FOR DTC
  1. Check for DTCs.

    OK:
    DTC B2799/99 is not output.



NG
REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
OK

END (TRANSPONDER KEY ECU IS DEFECTIVE)