Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat)

FRONT SEAT ASSEMBLY (for Manual Seat) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH (for Driver Side)


    B278193
  1. Install the front seat cushion edge protector LH as shown in the illustration.



2. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH (for Front Passenger Side)

HINT:
Use the same procedure described for the LH side.



3. INSTALL LOWER RECLINING ADJUSTER ARM SUB-ASSEMBLY LH


    B278194
  1. for Driver Side:

    1. Apply MP grease to the locations shown in the illustration.
      Text in Illustration 
      V100135
      MP Grease

  1. Using a T40 "TORX" socket wrench, install the lower reclining adjuster arm sub-assembly LH with the 2 "TORX" bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. for Front Passenger Side:
    Install the lower reclining adjuster arm sub-assembly LH with the 3 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }



4. INSTALL LOWER RECLINING ADJUSTER ARM SUB-ASSEMBLY RH
  1. for Driver Side:

    HINT:
    Use the same procedure described for the LH side.

  1. for Front Passenger Side:

    HINT:
    Use the same procedure described for the LH side.



5. INSTALL VERTICAL ADJUSTING SHAFT SUB-ASSEMBLY (for Driver Side)


    B278195
  1. Apply MP grease to the locations shown in the illustration.
    Text in Illustration 
    V100135
    MP Grease



    B277650
  1. Connect the vertical adjusting shaft sub-assembly to the 2 lower reclining adjuster arms to install it.



    B278196E01
  1. Connect the 2 vertical travel links to the vertical adjusting shaft sub-assembly.
    Text in Illustration 
    *1
    Vertical Travel Link

  1. Install 2 new E-rings.

  1. Temporarily install the vertical seat adjuster knob LH.



    B278197E01
  1. Turn the vertical seat adjuster knob LH as much as possible in the direction indicated by arrow A in the illustration.
    Text in Illustration 
    *1
    Vertical Adjusting Shaft Sub-assembly
    *2
    Lower Reclining Adjuster Arm Sub-assembly
    *3
    Hole
    *a
    Arrow A
    *b
    Arrow B

  1. Mesh the gear of the vertical adjusting shaft sub-assembly with the gear of the lower reclining adjuster arm sub-assembly.

  1. Align the holes of the vertical adjusting shaft sub-assembly and lower reclining adjuster arm sub-assembly by turning the vertical seat adjuster knob LH in the direction indicated by arrow B in the illustration.

  1. Remove the vertical seat adjuster knob LH.



6. INSTALL FRONT NO. 2 SEAT ADJUSTER PIN LH (for Driver Side)
  1. Using a 6 mm socket hexagon wrench, install the front No. 2 seat adjuster pin LH.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



7. INSTALL SEAT SPRING (for Driver Side)
  1. Temporarily install the vertical seat adjuster knob LH.

  1. Turn the vertical seat adjuster knob LH clockwise and move the lower reclining adjuster arm sub-assembly to the uppermost position.

  1. Remove the vertical seat adjuster knob LH.



    B278198
  1. Install the seat spring as shown in the illustration.

  1. Using pliers, push together the tabs that hold the seat spring.



8. INSTALL SEAT TRACK HANDLE SUB-ASSEMBLY LH


    B278199
  1. Apply MP grease to the locations shown in the illustration.
    Text in Illustration 
    V100135
    MP Grease



    B278200
    B278184
  1. Attach the 2 springs to install the seat track handle sub-assembly LH as shown in the illustration.

    HINT:
    The seat track handle sub-assembly LH will get caught on the springs when installing it. Detach the springs to install the seat track handle sub-assembly LH.



9. INSTALL FRONT SEAT ADJUSTER ROD (for Driver Side)
  1. Install the front seat adjuster rod with the 2 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }



10. INSTALL FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH
  1. Install the front seat cushion frame sub-assembly LH with the 4 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }



11. INSTALL FRONT SEAT CUSHION PROTECTOR


    B276738
  1. Install the 2 front seat cushion protectors.



12. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


  1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B278517E03


    Text in Illustration 
    *A
    except Sports Seat Type
    *B
    for Sports Seat Type
    *1
    Hog Ring Pliers
    -
    -

  1. Attach the hooks to install the separate type front seat cushion cover with pad to the front seat cushion frame sub-assembly LH.



    B276735
  1. Bend the 2 front seat cushion frame claws downward.



    B278201E01
  1. Using hog ring pliers, attach the separate type front seat cushion cover to the front seat cushion frame sub-assembly LH with new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers



    B278178
  1. for Front Passenger Side:
    Attach the wire harness clamp.



    B278202E01
  1. Using hog ring pliers, attach the separate type front seat cushion cover to the front seat cushion frame sub-assembly LH with new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers



13. INSTALL NO. 1 SEATBACK CLOTH (except Sports Seat Type, for TASA Made)


    B215906
  1. Install the No. 1 seatback cloth to the separate type front seatback spring assembly.



14. INSTALL SEPARATE TYPE FRONT SEATBACK PAD


    B207459
  1. Install the separate type front seatback pad to the separate type front seatback spring assembly.



15. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


  1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B290623E01


    Text in Illustration 
    *A
    except Sports Seat Type
    *B
    for Sports Seat Type
    *1
    Hog Ring Pliers
    -
    -
    *a
    Front view of front seatback
    *b
    Rear view of front seatback

  1. Attach the 4 claws to install the 2 front seat headrest support assemblies.



    B290624
  1. for Front Passenger Side, w/ Front Seat Side Airbag:
    Attach the separate type front seatback cover bracket and install the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    After the separate type front seatback cover is installed, make sure the separate type front seatback cover bracket is not twisted.



    B277651
  1. Pass the straps of the separate type front seatback cover through the holes of the separate type front seatback pad.



    B209095E03
  1. Using hog ring pliers, attach the 2 straps of the separate type front seatback cover to the separate type front seatback spring assembly with new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers



    B290625
  1. for Front Passenger Side, w/ Front Seat Side Airbag:
    Pass the front seat airbag wire harness through the hole of the separate type front seatback cover.



    B290626E01
  1. Using hog ring pliers, attach the separate type front seatback cover with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

    Text in Illustration 
    *1
    Hog Ring Pliers

  1. Install the front seatback assembly with the 4 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



16. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY (for Front Passenger Side, w/ Front Seat Side Airbag)


    B290627E01
  1. Using hog ring pliers, attach the separate type front seat cushion cover and the rubber bands of the separate type front seatback cover to the front seat cushion frame sub-assembly LH with new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers

  1. Install the separate type front seatback assembly with the 4 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



    B290616
  1. Attach the 3 front seat airbag wire harness clamps.



17. INSTALL SEATBACK SPRING LH


    B277652
  1. Install the seatback spring LH.



18. INSTALL FRONT SEAT CUSHION SHIELD LH


B278205E01
  1. Attach the guide and 2 hooks in the order shown in the illustration to install the front seat cushion shield LH.
    Text in Illustration 
    *1
    Guide
    *2
    Hook

  1. Install the 2 screws.



19. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    B278206
  1. Attach the claw to install the reclining adjuster release handle LH.



20. INSTALL VERTICAL SEAT ADJUSTER KNOB LH (for Driver Side)


B278207
  1. Install the snap ring to the vertical seat adjuster knob LH.

  1. Install the vertical seat adjuster knob LH.



21. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


B278208E01
  1. Attach the 2 hooks in the order shown in the illustration to install the front seat inner cushion shield LH.

  1. Install the 2 screws.



22. INSTALL FRONT SEAT CUSHION COVER LH
  1. Install the front seat cushion cover LH.



23. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)


B120318
  1. Install the buckle cover on the seat belt.



    B087821E01
  1. Install the seat belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding part of the seat adjuster.

  1. Attach the wire harness to the clamp.



    B087811E01
  1. Attach the clamp as shown in the illustration.



24. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)


B113100E01
  1. w/ Passenger seat belt warning light:
    Attach the 2 clamps as shown in the illustration.

  1. w/ Passenger seat belt warning light:
    Connect the connector.



    B113101E01
  1. Install the buckle cover on the inner belt.



    B084928E01
  1. w/ Passenger seat belt warning light:
    Attach the wire harness to the clamp.

  1. Install the seat belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding part of the seat adjuster.