SFI SYSTEM (w/o Secondary Air Injection System) > Fuel Pump Control Circuit |


| 1.PERFORM ACTIVE TEST (OPERATE C/OPN RELAY) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Fuel Pump.
Check the operation of the relay while operating it using the intelligent tester.
|
| ||||
| NG | |
| 2.CHECK ECM POWER SOURCE CIRCUIT |
Check ECM Power Source Circuit (Click here).
|
| ||||
| OK | |
| 3.CHECK ECM (FC VOLTAGE) |
![]() |
Turn the ignition switch ON.
Measure the voltage of the ECM connectors.
| Tester Connection | Specified Condition |
| E8-25 (FC) - E11-3 (E1) | 9 to 14 V |
|
| ||||
| OK | |
| 4.CHECK INTEGRATION NO.1 RELAY (C/OPN RELAY) |
![]() |
Remove the integration relay from the engine room junction block.
Measure the voltage of the C/OPN relay.
| Terminal Connection | Condition | Specified Condition |
| 1J-8 - Body ground | Engine cranking | 10 to 14 V |
|
| ||||
| OK | |
| 5.INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
|
| ||||
| OK | |
| 6.CHECK WIRE HARNESS (FUEL PUMP - INTEGRATION RELAY (C/OPN RELAY) AND BODY GROUND) |
![]() |
Remove the integration relay from the engine room junction block.
Disconnect the 1J integration relay connector.
Disconnect the F14 fuel pump connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| 1J-8 - F14-4 | Below 1 Ω |
| F14-5 - Body ground | Below 1 Ω |
| 1J-8 or F14-4 - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 7.CHECK WIRE HARNESS (INTEGRATION RELAY (C/OPN RELAY) - ECM AND BODY GROUND) |
![]() |
Remove the integration relay from the engine room junction block.
Disconnect the 1J integration relay connector.
Disconnect the E8 ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| 1J-7 - E8-25 (FC) | Below 1 Ω |
| 1J-7 or E8-25 (FC) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| 1J-6 - Body ground | 9 to 14 V |
|
| ||||
| OK | ||
| ||
| 1.INSPECT OPERATION OF FUEL PUMP |
Operation of fuel pump (Click here).
|
| ||||
| NG | |
| 2.CHECK ECM POWER SOURCE CIRCUIT |
Check ECM Power Source Circuit (Click here).
|
| ||||
| OK | |
| 3.CHECK ECM (FC VOLTAGE) |
![]() |
Turn the ignition switch ON.
Measure the voltage of the ECM connectors.
| Tester Connection | Specified Condition |
| E8-25 (FC) - E11-3 (E1) | 9 to 14 V |
|
| ||||
| OK | |
| 4.CHECK INTEGRATION NO.1 RELAY (C/OPN RELAY) |
![]() |
Remove the integration relay from the engine room junction block.
Measure the voltage of the C/OPN relay.
| Tester Connection | Condition | Specified Condition |
| 1J-8 - Body ground | Engine cranking | 10 to 14 V |
|
| ||||
| OK | |
| 5.INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
|
| ||||
| OK | |
| 6.CHECK WIRE HARNESS (FUEL PUMP - INTEGRATION RELAY (C/OPN RELAY) AND BODY GROUND) |
![]() |
Disconnect the 1J integration relay connector from the engine room junction block.
Disconnect the F14 fuel pump connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| 1J-8 - F14-4 | Below 1 Ω |
| F14-5 - Body ground | Below 1 Ω |
| 1J-8 or F14-4 - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 7.CHECK WIRE HARNESS (INTEGRATION RELAY (C/OPN RELAY) - ECM AND BODY GROUND) |
![]() |
Remove the integration relay from the engine room junction block.
Disconnect the 1J integration relay connector.
Disconnect the E8 ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| 1J-7 - E8-25 (FC) | Below 1 Ω |
| 1J-7 or E8-25 (FC) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| 1J-6 - Body ground | 9 to 14 V |
|
| ||||
| OK | ||
| ||