Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/o Secondary Air Injection System)

SFI SYSTEM (w/o Secondary Air Injection System) > Fuel Injector Circuit

for Preparation Click here


DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM


A120229E01


INSPECTION PROCEDURE

1.CHECK ECM (#10, #20, #30, #40 VOLTAGE)
A119979E03

A078423E07

  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    E10-6 (#10) - E11-7 (E01)
    9 to 14 V
    E10-5 (#20) - E11-7 (E01)
    9 to 14 V
    E10-2 (#30) - E11-7 (E01)
    9 to 14 V
    E10-1 (#40) - E11-7 (E01)
    9 to 14 V

HINT:
Reference: Inspect using the oscilloscope.
Check the waveform of the ECM connector.

OK:
Tester Connection
Specified Condition
E10-6 (#10) - E11-7 (E01)
Correct waveform is as shown
E10-5 (#20) - E11-7 (E01)
Correct waveform is as shown
E10-2 (#30) - E11-7 (E01)
Correct waveform is as shown
E10-1 (#40) - E11-7 (E01)
Correct waveform is as shown

Tool Setting
Condition
20 V/DIV., 100 or 1 msec./DIV.
Idling


OK
Go to step 6
NG


2.INSPECT FUEL INJECTOR ASSEMBLY (RESISTANCE)
  1. Inspect fuel injector .



NG
REPLACE FUEL INJECTOR ASSEMBLY
OK


3.INSPECT FUSE (INJ)
G034710E03
  1. Remove the INJ fuse from the instrument panel junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESSES AND COMPONENTS CONNECTED TO FUSE
OK


4.CHECK WIRE HARNESS OF MISFIRING CYLINDER (INJECTOR - ECM, INJECTOR - INJ FUSE)
G034950E03
  1. Check the wire harness between the injector and ECM.

    1. Disconnect the F4, F5, F6 and/or F7 injector connectors.

    2. Disconnect the E10 ECM connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      F4-2 - E10-6 (#10)
      Below 1 Ω
      F5-2 - E10-5 (#20)
      Below 1 Ω
      F6-2 - E10-2 (#30)
      Below 1 Ω
      F7-2 - E10-1 (#40)
      Below 1 Ω
      F4-2 or E10-6 (#10) - Body ground
      10 kΩ or higher
      F5-2 or E10-5 (#20) - Body ground
      10 kΩ or higher
      F6-2 or E10-2 (#30) - Body ground
      10 kΩ or higher
      F7-2 or E10-1 (#40) - Body ground
      10 kΩ or higher

  1. Check the wire harness between the injector and INJ fuse.

    1. Disconnect the F4, F5, F6 and F7 injector connectors.

    2. Remove the INJ fuse from the instrument panel junction block.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      F4-1 - J/B INJ fuse terminal 2
      Below 1 Ω
      F5-1 - J/B INJ fuse terminal 2
      Below 1 Ω
      F6-1 - J/B INJ fuse terminal 2
      Below 1 Ω
      F7-1 - J/B INJ fuse terminal 2
      Below 1 Ω
      F4-1 or J/B INJ fuse terminal 2 - Body ground
      10 kΩ or higher
      F5-1 or J/B INJ fuse terminal 2 - Body ground
      10 kΩ or higher
      F6-1 or J/B INJ fuse terminal 2 - Body ground
      10 kΩ or higher
      F7-1 or J/B INJ fuse terminal 2 - Body ground
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.CHECK WIRE HARNESS (IGNITION SWITCH - INJ FUSE)
G034709E03
  1. Disconnect the I8 ignition switch connector.

  1. Remove the INJ fuse from the instrument panel junction block.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    I8-6 (IG2) - J/B INJ fuse terminal 1
    Below 1 Ω
    I8-6 (IG2) or J/B INJ fuse terminal 1 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

CHECK FOR ECM POWER SOURCE CIRCUIT 

6.CHECK WIRE HARNESS (ECM - BODY GROUND)
A065159E16
  1. Disconnect the E11 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E11-7 (E01) - Body ground
    Below 1 Ω
    E11-6 (E02) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


7.INSPECT FUEL INJECTOR ASSEMBLY (CHECK FUEL INJECTION VOLUME)
  1. Inspect fuel injector .



NG
REPLACE FUEL INJECTOR ASSEMBLY
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE