FRONT PROPELLER SHAFT ASSEMBLY (for TMT Made) > REASSEMBLY |
| 1. INSTALL UNIVERSAL JOINT SPIDER ASSEMBLY |
![]() |
Apply MP grease to a new spider and 2 new spider bearings.
Fit the spider into the flange yoke.
![]() |
Using SST, install the 2 spider bearings to the spider.
![]() |
Using SST, adjust the spider bearings so that: 1) the flange yoke does not overlap the snap ring grooves of the spider bearings; 2) the grooves are as wide as possible; and 3) the groove width on both sides is the same.
Install 2 new snap rings to the installed spider bearings. The snap rings must have equal thickness and allow 0 to 0.05 mm (0 to 0.00196 in.) of axial play.
| Part No. | Thickness | Mark |
| 90520-T0007 | 2.19 mm (0.0862 in.) | F |
| 90520-T0008 | 2.21 mm (0.0870 in.) | G |
| 90520-T0009 | 2.23 mm (0.0878 in.) | H |
| 90520-T0010 | 2.25 mm (0.0886 in.) | J |
| 90520-T0011 | 2.27 mm (0.0894 in.) | K |
| 90520-T0012 | 2.29 mm (0.0902 in.) | 1 |
| 90520-T0013 | 2.31 mm (0.0909 in.) | 2 |
| 90520-T0014 | 2.33 mm (0.0917 in.) | 3 |
| 90520-T0015 | 2.35 mm (0.0925 in.) | 4 |
| 90520-T0016 | 2.37 mm (0.0933 in.) | 5 |
| 90520-T0017 | 2.39 mm (0.0941 in.) | 6 |
| 90520-T0018 | 2.41 mm (0.0949 in.) | 7 |
| 90520-T0019 | 2.43 mm (0.0957 in.) | 8 |
| 90520-T0020 | 2.45 mm (0.0965 in.) | N |
| 90520-T0021 | 2.47 mm (0.0972 in.) | 10 |
| 90520-T0022 | 2.49 mm (0.0980 in.) | A |
| 90520-T0023 | 2.51 mm (0.0988 in.) | B |
| 90520-T0024 | 2.53 mm (0.0996 in.) | C |
| 90520-T0025 | 2.55 mm (0.1004 in.) | D |
| 90520-T0026 | 2.57 mm (0.1012 in.) | E |
![]() |
Using a plastic-faced hammer, tap the flange yoke until there is no clearance between the spider bearings and snap rings.
| *a | Hammering Point |
Align the matchmarks on the flange yoke and propeller shaft.
Install new spider bearings on the sleeve yoke side.
| 2. INSPECT UNIVERSAL JOINT SPIDER ASSEMBLY |
Clamp the propeller shaft in a vise between aluminum plates.
Check the spider bearings for wear or damage.
![]() |
Check the axial play of each spider bearing by turning the yoke while holding the shaft tightly.
| 3. INSPECT PROPELLER SHAFT GREASE FITTING DIRECTION |

| *1 | No. 1 Grease Fitting | *2 | No. 2 Grease Fitting |
| *3 | No. 3 Grease Fitting | - | - |
| *a | Spider grease fitting assembly direction for front propeller shaft assembly | *b | Rear Side |