Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)

AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) > Radio Broadcast cannot be Received (Bad Reception)

for Preparation Click here


WIRING DIAGRAM


E277657E08


INSPECTION PROCEDURE

1.CHECK IF RADIO AUTO-SEARCH FUNCTIONS PROPERLY
  1. Check the radio automatic station search function by activating it.

    OK:
    Automatic station search function stops on a station.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK OPTIONAL COMPONENTS
  1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

    OK:
    Optional components are installed.

    NOTICE:
    Do not remove optional components without permission of the customer.



NG
Go to step 3
OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE) 

3.CHECK ANTENNA FOR NOISE PRODUCTION
  1. Remove the quarter window assembly RH (window glass antenna wire) connector.

  1. With the ignition switch ACC, turn on the radio and choose the AM mode.

  1. Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna connector and check that noise can be heard from the speakers.

    OK:
    Noise occurs.



NG
Go to step 4
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)  

4.CHECK RADIO RECEIVER ASSEMBLY (ANTENNA)
E276819
  1. Remove the antenna connector from the radio receiver assembly.

  1. Turn the ignition switch to ACC with the radio receiver assembly connector connected.

  1. Turn on the radio and turn into AM mode.

  1. Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.

    OK:
    Noise occurs.



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


5.INSPECT RADIO RECEIVER ASSEMBLY


    E277921E01
  1. Disconnect the RA radio receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (ANT+) - Body ground
    Ignition switch ACC, radio switch on and FM or AM selected
    11 to 14 V



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


6.CHECK ANTENNA CORD SUB-ASSEMBLY


    E278669E03
  1. Disconnect the radio receiver assembly connector.

  1. Remove the antenna connector from the antenna with holder assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    RA-3 (MAIN) - 2
    Always
    Below 1 Ω
    RA-5 (ANT+) - 3
    Always
    Below 1 Ω
    RA-3 (MAIN) - Body ground
    Always
    10 kΩ or higher
    RA-5 (ANT+) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio Receiver Assembly)
    *b
    Front view of wire harness connector
    (to Antenna with Holder Assembly)



NG
REPLACE ANTENNA CORD SUB-ASSEMBLY (Click here)
OK


7.CHECK ANTENNA WITH HOLDER ASSEMBLY
  1. Replace the antenna with holder assembly and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received normally.



NG
Go to step 8
OK

END (ANTENNA WITH HOLDER ASSEMBLY IS DEFECTIVE) 

8.INSPECT QUARTER WINDOW ASSEMBLY RH
  1. Replace the roof antenna pole sub-assembly and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received normally.



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)