Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM

ANTI-LOCK BRAKE SYSTEM > ABS Warning Light Remains ON

for Preparation Click here


DESCRIPTION

When checking for a 2 digit DTC, the ABS warning light may remain on.

WIRING DIAGRAM


C248570E01


F100586E03


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Turn the ignition switch ON.

  1. Check that the ABS warning light illuminates.

  1. Check if the same DTCs are recorded.

    Result 
    Result
    Proceed to
    DTC is not output (when using intelligent tester)
    A
    DTC is not output (when not using intelligent tester)
    B
    DTC is output
    C



B
Go to step 9

C
REPAIR CIRCUIT INDICATED BY OUTPUT DTC
A


2.INSPECT SKID CONTROL ECU CONNECTOR
  1. Check that each ECU connector is properly installed.

    OK:
    Each ECU connector is properly installed.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3.READ VALUE USING INTELLIGENT TESTER (ECU IG POWER VOLTAGE)
  1. Using the Data List, check for proper functioning of the ECU IG power voltage.

    Skid control ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ECU IG Power Voltage
    ECU power supply voltage / too Low, Normal or too High
    Normal
    -
    Result 
    Result
    Proceed to
    Display is Normal (w/ Rear Differential Lock)
    A
    Display is Normal (w/o Rear Differential Lock)
    B
    Display is not Normal
    C



B
Go to step 7

C
Go to step 15
A


4.CHECK BRAKE ACTUATOR ASSEMBLY (EXI2 VOLTAGE OF SKID CONTROL ECU)
C122186E01
  1. Measure the voltage of the ECU.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S2-22 (EXI2) - Body ground
    Ignition switch ON
    Rear differential lock switch OFF
    8 to 14 V
    S2-22 (EXI2) - Body ground
    Ignition switch ON
    Rear differential lock switch ON
    Below 1.5 V



NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


5.INSPECT TRANSFER INDICATOR SWITCH (REAR DIFFERENTIAL LOCK)


    F052057E03
  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Pushed
    Below 1 Ω
    1 - 2
    Not pushed
    10 kΩ or higher



NG
REPLACE TRANSFER INDICATOR SWITCH (REAR DIFFERENTIAL LOCK)
OK


6.CHECK WIRE HARNESS (TRANSFER INDICATOR SWITCH - SKID CONTROL ECU AND BODY GROUND)
C123166E14
  1. Disconnect the S2 ECU connector.

  1. Disconnect the T30 switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    T30-2 -S2-22 (EXI2)
    Below 1 Ω
    T30-2 - Body ground
    10 kΩ or higher
    T30-1 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


7.CHECK ABS WARNING LIGHT
C108884E08
  1. Disconnect the S2 ECU connector.

  1. Turn the ignition switch ON.

  1. Using a service wire, connect terminal WA to GND1 or GND2 of the S2 ECU connector. Check the ABS warning light.

    OK:
    ABS warning light turns off.

  1. Turn the ignition switch OFF.

  1. Remove the service wire.

  1. Turn the ignition switch ON. Check the ABS warning light.

    OK:
    ABS warning light illuminates.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


8.CHECK WIRE HARNESS (SKID CONTROL ECU - COMBINATION METER AND BODY GROUND)
C108898E47
  1. Disconnect the S2 ECU connector.

  1. Disconnect the C26 meter connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    S2-13 (WA) - C26-38
    Below 1 Ω
    S2-13 (WA) - Body ground
    10 kΩ or higher
    S2-2 (GND1) - Body ground
    Below 1 Ω
    S2-24 (GND2) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY 

9.INSPECT SKID CONTROL ECU CONNECTOR
  1. Check that each ECU connector is properly installed.

    OK:
    Each ECU connector is properly installed.

    Result 
    Result
    Proceed to
    OK (w/ Rear Differential Lock)
    A
    OK (w/o Rear Differential Lock)
    B
    NG
    C



B
Go to step 13

C
CONNECT CONNECTOR TO ECU CORRECTLY
A


10.CHECK BRAKE ACTUATOR ASSEMBLY (EXI2 VOLTAGE OF SKID CONTROL ECU)


    C122186E01
  1. Measure the voltage of the ECU.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S2-22 (EXI2) - Body ground
    Ignition switch ON
    Rear differential lock switch OFF
    8 to 14 V
    S2-22 (EXI2) - Body ground
    Ignition switch ON
    Rear differential lock switch ON
    Below 1.5 V



NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


11.CHECK TRANSFER INDICATOR SWITCH (REAR DIFFERENTIAL LOCK)


    F052057E03
  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Pushed
    Below 1 Ω
    1 - 2
    Not pushed
    10 kΩ or higher



NG
REPLACE TRANSFER INDICATOR SWITCH (REAR DIFFERENTIAL LOCK)
OK


12.CHECK WIRE HARNESS (TRANSFER INDICATOR SWITCH - SKID CONTROL ECU AND BODY GROUND)
C123166E14
  1. Disconnect the S2 ECU connector.

  1. Disconnect the T30 switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    T30-2 - S2-22 (EXI2)
    Below 1 Ω
    T30-2 - Body ground
    10 kΩ or higher
    T30-1 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


13.CHECK ABS WARNING LIGHT
C108884E10
  1. Disconnect the S2 ECU connector.

  1. Turn the ignition switch ON.

  1. Using a service wire, connect terminal WA to GND1 or GND2 of the S2 ECU connector. Check the ABS warning light.

    OK:
    ABS warning light turns off.

  1. Turn the ignition switch OFF.

  1. Remove the service wire.

  1. Turn the ignition switch ON. Check the ABS warning light.

    OK:
    ABS warning light illuminates.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


14.CHECK WIRE HARNESS (SKID CONTROL ECU - COMBINATION METER AND BODY GROUND)
C108898E31
  1. Disconnect the S2 ECU connector.

  1. Disconnect the C26 meter connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    S2-13 (WA) - C26-38
    Below 1 Ω
    S2-13 (WA) - Body ground
    10 kΩ or higher
    S2-2 (GND1) - Body ground
    Below 1 Ω
    S2-24 (GND2) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY 

15.CHECK WIRE HARNESS (SKID CONTROL ECU - BODY GROUND)
C108884E09
  1. Disconnect the S2 ECU connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S2-25 (IG1) - Body ground
    Ignition switch ON
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY