STEERING PAD > DISPOSAL |
| 1. PRECAUTION |
| 2. DISPOSE OF STEERING PAD (WHEN INSTALLED IN VEHICLE) |
![]() |
Check the function of SST.
![]() |
Connect SST to the 12 V battery.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
| *1 | Battery |
Check the function of SST.
Press the SST activation switch and check that the LED of the SST activation switch comes on.
Disconnect SST from the 12V battery.
Read the precaution (Click here).
Disconnect the cable from the negative (-) battery terminal.
Remove the steering column cover lower .
![]() |
Install SST.
Disconnect the airbag connector (yellow colored) from the spiral cable with steering sensor.
Connect SST connector to the airbag connector of the spiral cable with steering sensor.
![]() |
Move SST at least 10 m (32.8 ft.) away from the front side window.
| *1 | Battery |
| *a | 10 m or more |
Maintaining enough clearance for SST wire harness in the front side window, close all doors and windows of the vehicle.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
Deploy the airbag.
Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.
Press the SST activation switch and deploy the airbag.
| 3. DISPOSE OF STEERING PAD (WHEN NOT INSTALLED IN VEHICLE) |
![]() |
Check the function of SST (See previous step).
Remove the steering pad (Click here).
![]() |
Using a service-purpose wire harness for the vehicle, tie down the steering pad to a disc wheel.
| *a | Wire Harness Diameter |
| *b | Stripped Wire Harness Section |
![]() |
Install the 2 bolts with washers into the 2 bolt holes of the steering pad.
![]() |
After connecting SST to each other, connect them to the steering pad.
![]() |
Wind 3 wire harnesses at least 2 times each around the bolts installed on the left and right sides of the steering pad.
| *a | 2 times or more |
Face the airbag deployment side of the steering pad upward. Separately tie the left and right sides of the steering pad to a disc wheel through the hub nut holes. Position the SST connector so that it hangs downward through the hub hole in the disc wheel.
![]() |
Install SST.
Connect SST connector.
![]() |
Move SST at least 10 m (32.8 ft.) away from the steering pad.
| *1 | Battery |
| *a | 10 m or more |
![]() |
Cover the steering pad with a cardboard box or tires.
| *a | Weight |
Covering method using a cardboard box: Cover the steering pad with the cardboard box and place weights on the cardboard box in 4 places with a total of at least 190 N (19 kgf, 41.8 lbf).
![]() |
Covering method using tires: Place at least 3 tires (without disc wheels) on top of the tire (with disc wheel and steering pad).
| *1 | Tires (3 or more) |
| *a | Inner Diameter |
| *b | Width |
![]() |
Tie the tires together with 2 wire harnesses.
![]() |
Deploy the airbag.
| *A | Using Cardboard Box |
| *B | Using Tires |
| *1 | Steering Pad |
| *2 | Battery |
| *a | 10 m or more |
Connect the SST red clip to the positive (+) battery terminal and the black clip to the negative (-) battery terminal.
Check that no one is within a 10 m (32.8 ft.) radius of the steering pad.
Press the SST activation switch and deploy the airbag.
![]() |
Dispose of the steering pad.
Remove the steering pad from the disc wheel.
Place the steering pad in a plastic bag, tie it tightly and dispose of it in the same way as other general parts.