Home › BRAKE › BRAKE › BRAKE MASTER CYLINDER (for TSAM Made)

BRAKE MASTER CYLINDER (for TSAM Made) > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY
  1. Install a new O-ring to the master cylinder.



    C247715
  1. Install the master cylinder and bracket (with 3-way) to the booster with the 2 nuts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }



    C247714E01
  1. Using a union nut wrench, connect the 5 brake lines labeled C to the master cylinder and 3-way.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Connect the brake fluid level warning switch connector labeled B to the master cylinder.

  1. for Manual Transmission:
    Connect the clutch reservoir tube labeled A to the master cylinder.



2. FILL RESERVOIR WITH BRAKE FLUID

Fluid:
SAE J1704 or FMVSS No. 116 DOT 4



3. BLEED AIR FROM BRAKE MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

    Fluid:
    SAE J1704 or FMVSS No. 116 DOT 4

  1. Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.



    C247712
  1. Slowly depress and hold the brake pedal.



    C247713
  1. Block the tube holes with your fingers, and then release the brake pedal.

  1. Remove the your fingers, slowly depress and hold the brake pedal, block the tube holes with your fingers again, and the n release the brake pedal. Repeat this step 3 or 4 times.

  1. Using a union nut wrench, connect the 2 brake tubes to the brake master cylinder assembly.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



4. BLEED AIR FROM BRAKE LINE
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    for front brake:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }
    for rear brake:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the cap.

  1. Bleed air from the brake line for each wheel by repeating the above procedures.



5. BLEED AIR FROM CLUTCH LINE (for Manual Transmission)
  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the clutch line.

    Fluid:
    Made
    Fluid
    except TSAM Made
    SAE J1703 or FMVSS No. 116 DOT 3
    for TSAM Made
    SAE J1704 or FMVSS No. 116 DOT 4

  1. Remove the bleeder plug cap.



    C112661E08
  1. Connect a vinyl tube to the bleeder plug.

  1. Depress the clutch pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. At the point when fluid stops coming out, tighten the bleeder plug, and then release the clutch pedal.

  1. Repeat the previous 2 steps until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Install the bleeder plug cap.

  1. Check that all the air has been bled out of the clutch line.

  1. Check for brake fluid leaks.

  1. Check the brake fluid level in the reservoir.

    1. w/o VSC:

    2. w/ VSC:

  1. Install the brake master cylinder reservoir filler cap assembly.



6. CHECK BRAKE FLUID LEVEL IN RESERVOIR


    F052092
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1704 or FMVSS No. 116 DOT 4

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



7. CHECK FOR BRAKE FLUID LEAKAGE