Home › BRAKE › BRAKE › BRAKE BOOSTER (for TSAM Made)

BRAKE BOOSTER (for TSAM Made) > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE BOOSTER ASSEMBLY
  1. Install a new gasket to the brake booster.



    C111300
  1. Install the booster with the 4 nuts.

    Torque:
    14 N*m{ 145 kgf*cm , 10 ft.*lbf }

  1. Install the push rod clevis.

  1. Apply a light coat of lithium soap base glycol grease to the clevis pin.



    C226773E01
  1. Install the clevis pin and a new clip.

    NOTICE:
    The clip must be installed as shown in the illustration.

  1. Install the return spring.

  1. Install a new grommet and check valve to the booster.

  1. Connect the vacuum hose.



2. CHECK AND ADJUST BRAKE BOOSTER PUSH ROD

HINT:
Adjust the booster push rod when the master cylinder is replaced with a new one. Adjustment is not necessary when the master cylinder is reinstalled and the booster is replaced with a new one.



    G028332E01
  1. Set SST on the master cylinder and lower the rod of SST until it just touches the piston.

    SST
    09737-00013  

    HINT:
    SST 09737-00012 can also be used.

  1. Apply chalk to the flat tip of the rod of SST. Turn SST upside down and measure the clearance between the brake booster push rod and SST.

    Standard clearance:
    0 mm (0 in.)

    If there is clearance between the main body of SST and the shell of the brake booster, the push rod is protruding too far. If the chalk does not stick to the tip of the brake booster push, the push rod protrusion is insufficient.



    F040006E01
  1. If the clearance is not as specified, adjust the length by holding the rod using SST and turning the tip of the rod using a 7 mm socket driver.

    SST
    09737-00020  

    NOTICE:
    Check the push rod clearance again after adjustment.



3. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY
(Click here)


4. FILL RESERVOIR WITH BRAKE FLUID

Fluid:
SAE J1703 or FMVSS No. 116 DOT 3



5. BLEED AIR FROM BRAKE MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

    Fluid:
    SAE J1709 or FMVSS No. 116 DOT3

  1. Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.



    C122638
  1. Slowly depress and hold the brake pedal.



    C122639
  1. Block the tube holes with your fingers, and then release the brake pedal.

  1. Remove the your fingers, slowly depress and hold the brake pedal, block the tube holes with your fingers again, and then release the brake pedal. Repeat this step 3 or 4 times.

  1. Using a union nut wrench, connect the 2 brake tubes to the brake master cylinder assembly.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



6. BLEED AIR FROM BRAKE LINE
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    for front brake:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }
    for rear brake:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the cap.

  1. Bleed air from the brake line for each wheel by repeating the above procedures.



7. BLEED AIR FROM CLUTCH LINE (for Manual Transmission)
  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the clutch line.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

  1. Remove the bleeder plug cap.



    C112661E08
  1. Connect a vinyl tube to the bleeder plug.

  1. Depress the clutch pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. At the point when fluid stops coming out, tighten the bleeder plug, and then release the clutch pedal.

  1. Repeat the previous 2 steps until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Install the bleeder plug cap.

  1. Check that all the air has been bled out of the clutch line.

  1. Check for brake fluid leaks.

  1. Check the brake fluid level in the reservoir.

    1. w/o VSC:

    2. w/ VSC:

  1. Install the brake master cylinder reservoir filler cap assembly.



8. CHECK AND ADJUST BRAKE PEDAL HEIGHT
(Click here)


9. CHECK BRAKE FLUID LEVEL IN RESERVOIR


F052092
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



10. CHECK FOR BRAKE FLUID LEAKAGE