Home › DRIVE LINE › DIFFERENTIAL › FRONT DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

FRONT DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL > REPLACEMENT

for Preparation Click here



1. REMOVE NO. 1 ENGINE UNDER COVER


2. REMOVE NO. 2 ENGINE UNDER COVER


3. DRAIN DIFFERENTIAL OIL


  1. for front differential:

    1. Stop the vehicle on a level surface.



    2. A272242E01
    3. Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, remove the differential filler plug and gasket.
      Text in Illustration 
      *1
      10 mm Straight Hexagon Wrench
      *2
      10 mm Union Nut Wrench
      *3
      Socket Adaptor

    4. Remove the drain plug and gasket, and drain the oil.

    5. Install a new gasket and the drain plug.

      Torque:
      65 N*m{ 660 kgf*cm , 48 ft.*lbf }

  1. for rear differential:

    1. Stop the vehicle on a level surface.

    2. Remove the differential filler plug and gasket.

    3. Remove the drain plug and gasket, and drain the oil.

    4. Install a new gasket and the drain plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }



4. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH
(Click here)


5. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



6. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    C290048E01
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  



7. INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


  1. Using SST and a hammer, tap in 2 new oil seals.

    SST
    09223-15020  
    09950-70010   (09951-07100)


    C277518E02


    Text in Illustration 
    *a
    for LH Side
    *b
    for RH Side
    *c
    Gap
    -
    -
    *1
    Differential
    *2
    Oil Seal

    NOTICE:
    1. Make sure the LH and RH oil seals are installed to the proper locations.
    2. Make sure that the lip of the oil seal is inserted into SST before tapping in the oil seal.
    3. Do not damage the oil seals.

    Standard Oil Seal Gap:
    0 +0.14 mm (0 +0.00511 in.)



8. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
(Click here)


9. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



10. ADD DIFFERENTIAL OIL


    D025304E51
  1. Add differential oil so that the oil level is within 5 mm (0 to 0.196 in.) from the bottom lip of the differential filler plug hole.
    Text in Illustration 
    *a
    0 to 5 mm (0 to 0.196 in.)

    NOTICE:
    1. After changing the oil, drive the vehicle, and then check the oil level again.
    2. Too much or too little oil will lead to differential problems.

    If necessary, fill the differential carrier with hypoid gear oil.

    Recommended Viscosity:
    Temperature
    Viscosity
    Above -18°C (0°F)
    SAE 90
    Below -18°C (0°F)
    SAE 80W-90 or SAE 80W

    Oil type:
    Item
    Oil type
    Front Differential
    Rear differential
    Hypoid gear oil API GL-5 or equivalent
    Rear differential (for LSD)
    Hypoid gear oil LSD API GL-5 or equivalent

    Standard Differential Oil Capacity:
    Item
    Specified Condition
    Front Differential
    1.40 to 1.50 liters (1.48 to 1.58 US qts., 1.23 to 1.32 Imp. qts.)
    Rear differential
    3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)
    4WD, Pre-runner and made for DANA
    2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.)
    w/ Differential lock
    2.85 to 2.95 liters (3.01 to 3.12 US qts., 2.51 to 2.60 Imp. qts.)

  1. Check for oil leakage when the oil level is low.



  1. for front differential:



      A272243E01
    1. Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, install a new gasket and the differential filler plug.

      SST
      09961-00950  
      Text in Illustration 
      *1
      10 mm Straight Hexagon Wrench
      *2
      10 mm Union Nut Wrench
      *3
      Socket Adaptor

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }

      NOTICE:
      1. Make sure all the tools are connected in a straight line.
      2. Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

        Formula:
        T' = T x L3 / (L1 + L2 + L3)
        - T' = Spec. value of torque wrench
        - T = Value of specified tightening torque
        - L1 = Length of union nut wrench
        - L2 = Length of SST
        - L3 = Length of torque wrench

  1. for rear differential:

    1. Install a new gasket and the differential filler plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }



11. INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }



12. INSTALL NO. 1 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }