FRONT DIFFERENTIAL CARRIER ASSEMBLY > DISASSEMBLY |
| 1. INSPECT DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH |
![]() |
Using SST and a dial indicator, measure the ring gear backlash.
| 2. INSPECT FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the runout of the companion flange vertically and laterally.
| *a | 30 mm (1.18 in.) |
| Item | Specified Condition |
| Vertical runout | 0.10 mm (0.00394 in.) |
| Lateral runout | 0.10 mm (0.00394 in.) |
| 3. REMOVE FRONT DIFFERENTIAL TUBE ASSEMBLY |
![]() |
Remove the 4 bolts.
Using a plastic-faced hammer, tap out the differential tube.
| 4. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL LH |
![]() |
Using SST, tap out the oil seal.
| 5. REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT |
![]() |
Using SST and a hammer, loosen the staked part of the nut.
![]() |
Using SST to hold the companion flange, remove the nut.
| *a | Turn |
| *b | Hold |
| 6. REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR |
![]() |
Using SST, remove the companion flange with dust deflector.
| 7. REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL |
![]() |
Using SST, remove the oil seal.
| *1 | Oil Seal |
| *2 | Oil Slinger |
| 8. REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER |
![]() |
Remove the oil slinger from the drive pinion.
| 9. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING |
![]() |
Using SST, remove the roller bearing (inner) from the drive pinion.
| 10. REMOVE DIFFERENTIAL SIDE BEARING RETAINER |
Remove the 10 bolts and tap out the retainer with a plastic-faced hammer.
| 11. REMOVE DIFFERENTIAL CASE ASSEMBLY |
| 12. REMOVE DIFFERENTIAL DRIVE PINION |
| 13. REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER |
Remove the bearing spacer from the drive pinion.
| 14. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
Using SST and a press, press out the roller bearing (inner) and drive pinion plate washer from the drive pinion.
| 15. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
Using a brass bar and hammer, tap out the roller bearing (outer).
| 16. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING |
![]() |
Using SST, remove the roller bearing (outer).
| *a | Turn |
| *b | Hold |
| 17. REMOVE FRONT DIFFERENTIAL OIL STORAGE RING |
Using a brass bar and hammer, tap out the oil storage ring.
| 18. REMOVE FRONT DIFFERENTIAL CASE BEARING |
![]() |
Using SST and a press, press out the case bearing (outer) and plate washer from the bearing retainer.
![]() |
Using SST and a press, press out the case bearing (outer) and plate washer from the differential carrier.
| 19. REMOVE DIFFERENTIAL RING GEAR |
![]() |
Place matchmarks on the ring gear and differential case.
| *1 | Matchmark |
Remove the 10 ring gear set bolts.
![]() |
Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.
| 20. REMOVE FRONT DIFFERENTIAL CASE BEARING |
![]() |
Using SST, remove the 2 case bearings (inner) from the differential case.
| *a | Notch |
| *b | Turn |
| *c | Hold |
| 21. DISASSEMBLE DIFFERENTIAL CASE |
![]() |
Using a chisel and hammer, unstake the differential case.
![]() |
Using a pin punch and hammer, tap out the straight pin.
![]() |
Remove the following parts from the differential case.
![]() |
| 22. INSPECT DIFFERENTIAL GEAR KIT |
Check that the differential pinion and differential side gear are not damaged.
If the differential pinion or differential side gear is damaged, replace the differential gear kit.
| 23. INSPECT FRONT DIFFERENTIAL CASE |
Check that the differential case is not damaged.
If the differential case is damaged, replace it.
| 24. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL RH |
![]() |
Using SST, tap out the oil seal from the differential tube.
| 25. REMOVE DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH |
![]() |
Using a snap ring expander, remove the snap ring.
Remove the shaft from the differential tube.
| 26. REMOVE FRONT DIFFERENTIAL SIDE GEAR SHAFT BEARING RH |
Using a snap ring expander, remove the snap ring.
![]() |
Using SST, a brass bar and press, press out the shaft bearing RH.