Home › DRIVE LINE › DIFFERENTIAL › DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock)

DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) > DISASSEMBLY

for Preparation Click here



1. SECURE REAR DIFFERENTIAL CARRIER ASSEMBLY


    C236647
  1. Secure the differential carrier.



2. INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    C236648E01
  1. Using a dial indicator, measure the runout of the companion flange vertically and laterally.
    Text in Illustration 
    *a
    30 mm (1.18 in.)

    Maximum Runout:
    Runout
    Maximum
    Vertical runout
    0.10 mm (0.00394 in.)
    Lateral runout
    0.10 mm (0.00394 in.)

    1. If the runout is more than the maximum, replace the companion flange.



3. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR


    C237323
  1. Using a dial indicator, measure the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.00276 in.)

    1. If the runout is more than the maximum, replace the ring gear with a new one.



4. INSPECT DIFFERENTIAL RING GEAR BACKLASH


    C237324
  1. Using a dial indicator, measure the backlash of the ring gear.

    Standard backlash:
    0.13 to 0.18 mm (0.00512 to 0.00708 in.)

    1. If the backlash is not within the specification, adjust the side bearing preload or perform repairs as necessary.

      HINT:
      Perform the measurement at 3 or more positions around the circumference of the ring gear.



5. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


    C236639
  1. Using a torque wrench, measure the preload.

    Standard Preload (Starting Torque):
    Bearing
    Specified Condition
    New
    1.1 to 1.6 N*m (12 to 16 kgf*cm, 10 to 14 in.*lbf)
    Reused
    0.6 to 0.8 N*m (7 to 8 kgf*cm, 6 to 7 in.*lbf)

    1. If the result is not as specified, adjust the preload .



6. INSPECT TOTAL PRELOAD


    C236639
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Standard Total Preload:
    Bearing
    Specified Condition
    New
    0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload
    Reused
    0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload

    1. If the result is not as specified, adjust the preload.



7. REMOVE DIFFERENTIAL LOCK SHIFT ACTUATOR


    C238709
  1. Disconnect the breather hose.

  1. Disconnect the connector.



    C237326
  1. Remove the bolt, nut and actuator from the differential carrier.

  1. Remove the O-ring.



8. REMOVE NO. 4 TRANSFER INDICATOR SWITCH


    C237327E01
  1. Remove the switch and gasket.
    Text in Illustration 
    *1
    Gasket
    *2
    Switch



9. REMOVE REAR DIFFERENTIAL LOCK SHIFT FORK SHAFT


C237328E01
Text in Illustration 
*1
Steel Ball
*2
Spring Seat
*3
Spring
*4
Screw Plug
  1. Using a 6 mm hexagon wrench, remove the 2 screw plugs.

  1. Remove the spring seat, spring and steel ball.



    C237329E01
  1. Using a 5 mm pin punch and hammer, tap out the slotted spring pin from the shift fork shaft.
    Text in Illustration 
    *1
    Shift Fork Shaft
    *2
    Pin Punch
    *3
    Slotted Spring Pin



    C237330
  1. Remove the 2 bolts from the shaft retainer.

  1. Using a plastic-faced hammer, tap on the retainer to separate it from the differential case.

  1. Remove the shift fork shaft.



10. REMOVE REAR DRIVE PINION NUT


    C236628E01
  1. Using SST and a hammer, loosen the staked part of the nut.

    SST
    09930-00010   (09931-00010, 09931-00020)



    C236629E01
  1. Using SST to hold the companion flange in place, remove the nut.

    SST
    09330-00021   (09330-00030)
    Text in Illustration 
    *a
    Turn
    *b
    Hold



11. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR


    C238724
  1. Using SST, remove the companion flange with dust deflector.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



12. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


    C236631E01
  1. Using SST, remove the oil seal.

    SST
    09308-10010  
    Text in Illustration 
    *1
    Oil Seal
    *2
    Oil Slinger



13. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


    C237315
  1. Remove the oil slinger from the drive pinion.



14. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C236655E02
  1. Using SST, remove the roller bearing (inner) from the drive pinion.

    SST
    09556-22010  
    Text in Illustration 
    *a
    Turn
    *b
    Hold



15. REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK


    C237331
  1. Remove the 2 bolts and 2 adjusting nut locks.



16. REMOVE DIFFERENTIAL CASE ASSEMBLY


    C237332E01
  1. Place matchmarks on the bearing cap and differential carrier.
    Text in Illustration 
    *1
    Matchmark

  1. Remove the 4 bolts and 2 differential bearing caps.

  1. Remove the 2 adjusting nuts.



    C237333
  1. Remove the rear differential case assembly from the differential carrier.

    HINT:
    Tag the 2 rear differential case bearings (outer) so that they can be reinstalled in the correct locations.



17. REMOVE DIFFERENTIAL DRIVE PINION
  1. Remove the drive pinion and bearing spacer from the differential carrier.



18. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


    C238710E01
  1. Using SST, remove the roller bearing (outer) from the carrier.

    SST
    09308-00010  



19. REMOVE DIFFERENTIAL OIL STORAGE RING


    C238707
  1. Using a brass bar and hammer, tap out the oil storage ring from the carrier.



20. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
  1. Remove the bearing spacer from the drive pinion.



21. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


    C237336
  1. Using a brass bar and hammer, tap out the rear tapered roller bearing (outer) from the carrier.
    If the bearing is damaged during removal, replace it.



22. REMOVE DIFFERENTIAL RING GEAR


    C237337E01
  1. Place matchmarks on the ring gear and differential case.
    Text in Illustration 
    *1
    Matchmark

  1. Using a screwdriver and hammer, pry out the staked portions of the lock plates.

  1. Remove the 10 ring gear set bolts and 5 lock plates.



    C237338
  1. Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.



23. INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT
If the ring gear runout is within the specified value (refer to the "Inspect Runout of Differential Ring Gear" procedure above), skip this step.
  1. Install the rear differential case bearings (outer) to the differential case.

  1. Install the differential case to the differential carrier.

  1. Install the 2 adjusting nuts.

  1. Install the 2 bearing caps to the differential carrier with the 4 bolts.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }



    C236665
  1. Using a dial indicator, measure the differential case runout.

    Maximum runout:
    0.07 mm (0.00276 in.)

  1. Remove the 4 bolts and 2 bearing caps.

  1. Remove the 2 adjusting nuts.

  1. Remove the differential case.

  1. Remove the rear differential case bearings (outer).



24. REMOVE REAR DIFFERENTIAL CASE BEARING


    C236666E01
  1. Using SST, remove the 2 bearings from the differential case.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00360)

    HINT:
    Do not remove the case bearings when not replacing the differential case.



25. DISASSEMBLE DIFFERENTIAL CASE


    C237340E01
  1. Place matchmarks on the LH and RH cases.
    Text in Illustration 
    *1
    Matchmark

  1. Remove the 8 bolts uniformly, a little at a time.



    C237341
  1. Using a plastic-faced hammer, tap out the LH case from the RH case.

  1. Remove the rear differential lock sleeve from the differential case LH.



    C237342E01
  1. Remove the following parts from the differential cases.

    1. (1) Side gear (2 pieces)
    2. (2) Side gear thrust washer (2 pieces)
    3. (3) Spider
    4. (4) Pinion gear (4 pieces)
    5. (5) Pinion gear thrust washer (4 pieces)



26. INSPECT REAR DIFFERENTIAL LOCK SLEEVE


    C237343
  1. Install the sleeve to the differential case LH and check that it moves smoothly.

  1. Install the sleeve to the side gear and check that it moves smoothly.



27. INSPECT SHIFT FORK AND SLEEVE


    C237344
  1. Using a feeler gauge, measure the clearance between the shift fork and sleeve.

    Standard clearance (reference):
    0.15 to 0.35 mm (0.00591 to 0.0137 in.)



28. INSPECT DIFFERENTIAL GEAR KIT
  1. Check that the differential pinion and differential side gear are not damaged.

    1. If the differential pinion or differential side gear is damaged, replace the differential gear kit.



29. INSPECT DIFFERENTIAL CASE
  1. Check that the differential case is not damaged.

    1. If the differential case is damaged, replace it.