Home › DRIVE LINE › DIFFERENTIAL › DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock)

DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) > REASSEMBLY

for Preparation Click here



1. ASSEMBLE DIFFERENTIAL CASE


    C237345
  1. Install the side gear thrust washer to the side gear.

  1. Install the 4 rear differential pinion gear thrust washers to the 4 rear drive pinion gears.

  1. Install the 4 rear differential pinion gear thrust washers and 4 rear drive pinion gears to the spider.

  1. Secure the differential case RH.



    C237346
  1. Install the rear differential side gear and rear differential spider to the differential case RH.



    C237347
  1. Using a dial indicator, measure the differential case RH backlash while holding the pinion toward the case.

    Standard backlash:
    0.05 to 0.20 mm (0.00197 to 0.00787 in.)

  1. Remove the rear differential spider from the differential case RH.



    C237348
  1. Install the rear differential side gear and rear differential spider to the differential case LH.

  1. Using a dial indicator, measure the differential case LH backlash while holding the pinion toward the case.

    Standard backlash:
    0.05 to 0.20 mm (0.00197 to 0.00787 in.)

    HINT:
    Using the table below, select 2 thrust washers which will ensure that the backlash is within the specifications.

    Standard Washer Thickness:
    Thickness mm (in.)
    Thickness mm (in.)
    0.88 to 0.92 (0.0347 to 0.0362)
    1.18 to 1.22 (0.0465 to 0.0480)
    0.98 to 1.02 (0.0386 to 0.0401)
    1.28 to 1.32 (0.0504 to 0.0519)
    1.08 to 1.12 (0.0426 to 0.0440)
    -



    C237349E01
  1. Align the matchmarks and assemble the RH and LH cases.
    Text in Illustration 
    *1
    Matchmark

  1. Using a plastic-faced hammer, install the differential case.

  1. Install the 8 bolts.

    Torque:
    54 N*m{ 547 kgf*cm , 40 ft.*lbf }

  1. Install the rear differential lock sleeve to the differential case LH.



2. INSTALL DIFFERENTIAL RING GEAR
  1. Clean the contact surfaces of the differential case and ring gear.

  1. Heat the ring gear in boiling water that is approximately 100°C (212°F).

  1. Carefully remove the ring gear from the boiling water.



    C236674E01
  1. After the moisture on the ring gear has completely evaporated, quickly align the matchmarks on the ring gear and differential case and install the ring gear to the differential case.
    Text in Illustration 
    *1
    Matchmark

  1. Temporarily install 5 new lock plates and the 10 bolts.

  1. After the ring gear cools down, diametrically tighten the 10 bolts uniformly in several passes.

    Torque:
    87 N*m{ 891 kgf*cm , 64 ft.*lbf }



    C236675E01
  1. Using a chisel and hammer, stake the 5 lock plates.

    HINT:
    Strike the tab labeled A so that it is flush with the flat surface of the bolt. Strike the tab labeled B so that half of the tab contacts the bolt as shown in the illustration.



3. INSTALL REAR DIFFERENTIAL CASE BEARING


    C237670E01
  1. Using SST and a press, press the bearing onto the differential case.

    SST
    09950-60010   (09951-00430, 09951-00470, 09951-00480, 09951-00550)
    09950-70010   (09951-00560, 09951-00570, 09951-07150)
    Text in Illustration 
    *A
    for LSD
    *B
    2 Pinion Type



4. INSPECT DIFFERENTIAL RING GEAR RUNOUT
  1. Install the differential case on the carrier, and install the 2 adjusting nuts so that there is no play in the bearing.

  1. Install the 2 bearing caps with the 4 bolts.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }



    C236649
  1. Using a dial indicator, measure the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.0028 in.)

  1. Remove the 2 bearing caps, 2 adjusting nuts and differential case.



5. INSTALL DIFFERENTIAL OIL STORAGE RING
  1. Using a brass bar and hammer, tap in a new oil storage ring.

    NOTICE:
    Be careful not to damage the oil storage ring.



6. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C236677E01
  1. Using SST and a press, press the bearing (outer) into the carrier.

    SST
    09316-60011   (09316-00011, 09316-00021)



7. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING


    C236678E01
  1. Using SST and a press, press the bearing (outer) into the carrier.

    SST
    09316-60011   (09316-00011, 09316-00041)



8. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING
  1. Install the plate washer to the drive pinion.

    HINT:
    First, install a washer that has the same thickness as the removed washer. After checking the tooth contact pattern, replace the washer with one of a different thickness if necessary.



    C236679E01
  1. Using SST and a press, press the bearing (inner) onto the drive pinion.

    SST
    09506-30012  



9. ADJUST DIFFERENTIAL DRIVE PINION PRELOAD


    C237303
  1. Install the drive pinion, rear drive pinion tapered roller bearing and rear differential drive pinion oil slinger.

    HINT:
    Install the spacer and oil seal after adjusting the gear contact pattern.



    C237304E01
  1. Using SST, install the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



    C237305E01
  1. Adjust the drive pinion preload by tightening the companion flange nut.

  1. Using SST to hold the companion flange in place, tighten the nut.

    SST
    09330-00021   (09330-00030)

    Torque:
    370 N*m{ 3773 kgf*cm , 273 ft.*lbf } or less

    NOTICE:
    1. As there is no spacer, tighten a little at a time. Be careful not to overtighten the nut.
    2. Apply hypoid gear oil LSD to drive pinion thread and nut seat face.

  1. Using a torque wrench, measure the preload.

    Standard Drive Pinion Preload (Starting Torque):
    Bearing
    Preload
    New bearing
    1.0 to 1.5 N*m (11 to 15 kgf*cm, 9 to 13 in.*lbf)
    Reused bearing
    0.5 to 0.7 N*m (6 to 7 kgf*cm, 5 to 6 in.*lbf)

    NOTICE:
    1. For a more accurate measurement, rotate the bearing forward and backward several times before measuring.
    2. Record the differential drive pinion preload for the total preload measurement.



10. INSTALL DIFFERENTIAL CASE ASSEMBLY


    C237353
  1. Apply MP grease to the rack of the shift fork and connecting part of the indicator switch.
    Text in Illustration 
    V100135
    MP grease

  1. Insert the shift fork into the differential carrier as shown in the illustration.



    C237354
  1. Place the outer race and adjusting nut on the left side of the sleeve.

    HINT:
    Check that the sleeve moves smoothly.



    C237333
  1. Insert the shift fork into the groove of the sleeve while holding the sleeve by hand, and install the case to the carrier.

    HINT:
    Make sure that there is backlash between the ring gear and drive pinion.



11. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT


    C237355
  1. Install the 2 adjusting nuts to the carrier, making sure the nuts are threaded properly.



12. INSPECT AND ADJUST DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH


    C237332E01
  1. Align the matchmarks on the cap and carrier.
    Text in Illustration 
    *1
    Matchmark



    C238708
  1. Install the right and left bearing caps with the 4 bolts.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }

    1. If the bearing cap does not fit tightly on the carrier, the adjusting nuts are not threaded properly.

      HINT:
      Reinstall the adjusting nuts if necessary.



    C237309E01
  1. Loosen the 4 bearing cap bolts to the point where the adjusting nuts can be turned by SST.
    Text in Illustration 
    *a
    for LH Side
    *b
    for RH Side

  1. Using SST, tighten the adjusting nut on the ring gear side until the ring gear has a backlash of about 0.2 mm (0.00787 in.).

    SST
    09504-00011  
    09960-10010   (09962-01000, 09963-00700)

  1. While turning the ring gear, use SST to tighten the adjusting nut on the drive pinion side. After the bearings have settled, loosen the adjusting nut on the drive pinion side.

    SST
    09504-00011  
    09960-10010   (09962-01000, 09963-00700)

  1. Using SST, tighten the adjusting nut 1 to 1.5 notches from the 0 preload position.



    C237324
  1. Using a dial indicator, adjust the ring gear backlash until it is within the specification.

    Standard backlash:
    0.13 to 0.18 mm (0.00512 to 0.00708 in.)

    HINT:
    1. The backlash is adjusted by turning the left and right adjusting nuts by an equal amount. For example, loosen the nut on the right side one notch and loosen the nut on the left side one notch.
    2. Perform the measurement at 3 or more positions around the circumference of the ring gear.



    C237332
  1. Tighten the bearing cap bolts.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }



13. INSPECT TOTAL PRELOAD


    C237317
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

  1. Using a torque wrench, measure the total preload.

    Standard Total Preload:
    Item
    Specified Condition
    New bearing
    0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload
    Reused bearing
    0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload

    If necessary, disassemble and inspect the differential.

    NOTICE:
    Record the differential ring gear preload.



14. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION


C237311
  1. Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.

  1. Hold the companion flange firmly in place and rotate the ring gear in both directions.



  1. Inspect the tooth contact pattern.


    1. C178076E02


    2. C237312E01
      If the teeth are not contacting properly, use the following chart to select a proper washer.
      Text in Illustration 
      *1
      Plate Washer

      Standard Plate Washer Thickness:
      Thickness mm (in.)
      Thickness mm (in.)
      1.69 to 1.71 (0.0666 to 0.0673)
      2.02 to 2.04 (0.0796 to 0.0803)
      1.72 to 1.74 (0.0678 to 0.0685)
      2.05 to 2.07 (0.0807 to 0.0814)
      1.75 to 1.77 (0.0689 to 0.0696)
      2.08 to 2.10 (0.0819 to 0.0826)
      1.78 to 1.80 (0.0701 to 0.0708)
      2.11 to 2.13 (0.0831 to 0.0838)
      1.81 to 1.83 (0.0713 to 0.0720)
      2.14 to 2.16 (0.0843 to 0.0850)
      1.84 to 1.86 (0.0725 to 0.0732)
      2.17 to 2.19 (0.0855 to 0.0862)
      1.87 to 1.89 (0.0737 to 0.0744)
      2.20 to 2.22 (0.0867 to 0.0874)
      1.90 to 1.92 (0.0748 to 0.0755)
      2.23 to 2.25 (0.0878 to 0.0885)
      1.93 to 1.95 (0.0760 to 0.0767)
      2.26 to 2.28 (0.0890 to 0.0897)
      1.96 to 1.98 (0.0772 to 0.0779)
      2.29 to 2.31 (0.0902 to 0.0909)
      1.99 to 2.01 (0.0784 to 0.0791)
      2.32 to 2.34 (0.0914 to 0.0921)



15. REMOVE REAR DRIVE PINION NUT


    C236628E01
  1. Using SST and a hammer, loosen the staked part of the nut.

    SST
    09930-00010   (09931-00010, 09931-00020)



    C236629E01
  1. Using SST to hold the companion flange in place, remove the nut.

    SST
    09330-00021   (09330-00030)
    Text in Illustration 
    *a
    Turn
    *b
    Hold



16. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR


    C238724
  1. Using SST, remove the companion flange with dust deflector.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



17. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


    C237315
  1. Remove the oil slinger from the drive pinion.



18. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C236632E01
  1. Using SST, remove the roller bearing (inner) from the drive pinion.

    SST
    09556-22010  



19. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER


    C236634
  1. Install a new bearing spacer.

    HINT:
    Make sure the spacer is installed correctly.



20. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C237314
  1. Install the bearing (inner) to the drive pinion.



21. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


    C237315
  1. Install the oil slinger to the drive pinion.



22. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL
  1. Apply MP grease to the lip of the oil seal.



    C236636E01
  1. Using SST and a hammer, tap in a new seal.

    SST
    09554-30011  
    Text in Illustration 
    *a
    Oil Seal Depth

    Standard oil seal depth:
    0 +/-0.3 mm (0 +/-0.0118 in.)



23. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR


    C238725
  1. Using SST, install the companion flange with dust deflector.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.

  1. Apply hypoid gear oil LSD to drive pinion thread and nut seat face.



    C237316E01
  1. Using SST to hold the companion flange in place, install a new nut.

    SST
    09330-00021   (09330-00030)
    Text in Illustration 
    *1
    Turn
    *1
    Hold

    Torque:
    370 N*m{ 3773 kgf*cm , 273 ft.*lbf } or less



24. INSPECT TOTAL PRELOAD


    C237317
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

  1. Using a torque wrench, measure the total preload.

    Standard Total Preload:
    Bearing
    Preload
    New bearing
    1.1 to 1.6 N*m (12 to 16 kgf*cm, 10 to 14 in.*lbf) + ring gear preload
    Reused bearing
    0.6 to 0.8 N*m (7 to 8 kgf*cm, 6 to 7 in.*lbf) + ring gear preload

    1. If necessary, disassemble and inspect the differential.



25. INSPECT DIFFERENTIAL RING GEAR BACKLASH


    C237324
  1. Using a dial indicator, measure the backlash of the ring gear.

    Standard backlash:
    0.13 to 0.18 mm (0.00512 to 0.00708 in.)

    1. If the backlash is not within the specification, adjust the side bearing preload or perform repairs as necessary.

      HINT:
      Perform the measurement at 3 or more positions around the circumference of the ring gear.



26. INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    C236648E01
  1. Using a dial indicator, measure the runout of the companion flange vertically and laterally.
    Text in Illustration 
    *a
    30 mm (1.18 in.)

    Maximum Runout:
    Runout
    Maximum
    Vertical runout
    0.10 mm (0.00394 in.)
    Lateral runout
    0.10 mm (0.00394 in.)

    1. If the runout is more than the maximum, replace the companion flange.



27. STAKE DRIVE PINION NUT


    C236640
  1. Using a chisel and hammer, stake the nut.



28. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK


    C237306
  1. Install the 2 adjusting nuts to the carrier, making sure the nuts are threaded properly.



29. INSTALL REAR DIFFERENTIAL LOCK SHIFT FORK SHAFT


    C237358E01
  1. Apply MP grease to the outer circuit of the fork shaft.
    Text in Illustration 
    *1
    Groove
    *2
    Hole

  1. Install the fork shaft so that the hole of the shift fork aligns with that of the shift fork shaft.



    C237359E01
  1. Remove any seal packing material.
    Text in Illustration 
    *1
    Seal packing

    NOTICE:
    Be careful not to drop oil on the contact surface of the differential carrier and shaft retainer.

  1. Apply seal packing to the carrier as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    HINT:
    Install the shaft retainer within 3 minutes after applying seal packing.



    C237360
  1. Clean the threads of the bolts and retainer bolts holes with toluene or trichloroethylene.

  1. Apply adhesive to 2 or 3 threads at the end of the mounting bolt.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Tighten the shaft retainer with the 2 bolts.

    Torque:
    23 N*m{ 237 kgf*cm , 17 ft.*lbf }



    C237361
  1. Using a 5 mm pin punch and hammer, tap in the slotted spring pin to the shift fork.



    C237362E01
  1. Shift the fork to the lock side.
    Text in Illustration 
    *1
    Lock



    C237466E01
  1. Install the steel ball, spring and spring seat.
    Text in Illustration 
    *1
    Steel Ball
    *2
    Spring
    *3
    Spring Seat
    *4
    Screw Plug

  1. Clean the threads of the 2 plug holes with toluene or trichloroethylene.

  1. Apply adhesive to the plug threads.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Using a 6 mm hexagon wrench, install the screw plugs.

    Torque:
    23 N*m{ 237 kgf*cm , 17 ft.*lbf }



30. INSPECT REAR DIFFERENTIAL LOCK SLEEVE


C237467
  1. Measure the distance between the sleeve and tip of the differential case when the differential is free, and when it is locked.

    Standard Distance:
    Position
    Specified Condition
    Lock
    17.44 to 18.86 mm (0.6866 to 0.7425 in.)
    Free
    32.40 to 33.90 mm (1.2756 to 1.3346 in.)



31. INSTALL NO. 4 TRANSFER INDICATOR SWITCH


    C121512E03
  1. Install the indicator switch and a new gasket.
    Text in Illustration 
    *1
    Gasket
    *1
    Switch

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }

  1. Connect the connector.



32. INSTALL DIFFERENTIAL LOCK SHIFT ACTUATOR
  1. Install a new O-ring to the actuator.

  1. Install the actuator to the differential carrier.

    Torque:
    27 N*m{ 270 kgf*cm , 20 ft.*lbf }



    C237468E01
  1. Check that the outermost rack tooth of the shift fork is almost directly above the center line of the actuator installation hole.
    Text in Illustration 
    *1
    Shift Fork
    *2
    Actuator Installation Hole
    V100135
    Outside



    C237469E01
  1. Check that the matchmarks on the pinion of the actuator are in the range between 2 and 8° clockwise of the center line of the actuator.
    Text in Illustration 
    *1
    Matchmark
    *a
    8°
    *b
    108°
    *c
    1.5 V

    NOTICE:
    1. If the matchmarks are not within the specified range, use dry cell batteries to rotate the pinion until the matchmarks are within the range.
    2. Do not apply positive (+) battery voltage directly between terminals.
    3. If the matchmarks come to the limit of the rotation range, do not apply any more voltage.

  1. Install a new O-ring to the actuator.

  1. Apply a light coat of gear oil to the O-ring.

  1. Apply MP grease to the gear parts.



    C237470E01
  1. Check that the outermost rack tooth of the shift fork aligns with the matchmarks on the pinion of the actuator.
    Text in Illustration 
    *1
    Knock Pin

  1. Install the actuator so that the long hole in the actuator fits with the knock pin on the carrier.

    HINT:
    Do not damage the O-ring of the actuator.

  1. Rotate the actuator counterclockwise so that the knock pin slides to the end of the hole as shown in the illustration.

  1. Install the bolt.

    Torque:
    27 N*m{ 270 kgf*cm , 20 ft.*lbf }