Home › SUSPENSION & AXLE › SUSPENSION › FRONT WHEEL ALIGNMENT

FRONT WHEEL ALIGNMENT > ADJUSTMENT

for Preparation Click here



1. INSPECT TIRE
  1. Inspect the tires (Click here).



2. INSPECT VEHICLE HEIGHT


C125201E01

NOTICE:
Before inspecting the wheel alignment, adjust the vehicle height to the specification.

  1. Press down on the vehicle several times to stabilize the suspension, and measure the vehicle height.

    Standard Vehicle Height (Unloaded Vehicle):
    Vehicle Model
    Front A - B
    Rear C - D
    KUN51L-IKMSY
    77 mm (3.03 in.)
    59 mm (2.32 in.)
    KUN51L-IKPSY
    79 mm (3.11 in.)
    61 mm (2.40 in.)
    GGN50L-IKMSK
    75 mm (2.95 in.)
    61 mm (2.40 in.)
    GGN50L-IKASK
    76 mm (2.99 in.)
    61 mm (2.40 in.)
    TGN61L-NKMDKG
    71 mm (2.80 in.)
    59 mm (2.32 in.)
    TGN61L-NKMDGG
    7-passenger
    72 mm (2.83 in.)
    59 mm (2.32 in.)
    5-passenger
    72 mm (2.83 in.)
    56 mm (2.20 in.)
    TGN61L-NKPDGG
    7-passenger
    72 mm (2.83 in.)
    60 mm (2.36 in.)
    5-passenger
    72 mm (2.83 in.)
    57 mm (2.24 in.)
    KUN51L-NKMSYG
    7-passenger
    77 mm (3.03 in.)
    61 mm (2.40 in.)
    5-passenger
    77 mm (3.03 in.)
    60 mm (2.36 in.)
    KUN51L-NKPSYG
    7-passenger
    78 mm (3.07 in.)
    61 mm (2.40 in.)
    5-passenger
    79 mm (3.11 in.)
    60 mm (2.36 in.)
    GGN50L-NKASKG
    76 mm (2.99 in.)
    61 mm (2.40 in.)
    GGN50L-NKASKF
    76 mm (2.99 in.)
    61 mm (2.40 in.)
    GGN50L-NKMSKF
    75 mm (2.95 in.)
    61 mm (2.40 in.)
    KUN51L-NKMSYF
    77 mm (3.03 in.)
    59 mm (2.32 in.)
    KUN51L-NKPSYF
    79 mm (3.11 in.)
    61 mm (2.40 in.)
    TGN51L-NKMSKF
    76 mm (2.99 in.)
    59 mm (2.32 in.)
    TGN51L-NKPSKF
    78 mm (3.07 in.)
    59 mm (2.32 in.)
    TGN61L-NKMSKF
    71 mm (2.80 in.)
    56 mm (2.20 in.)
    TGN61L-NKPSKF
    72 mm (2.83 in.)
    56 mm (2.20 in.)

    Measuring point:
    A:
    Ground clearance of front wheel center
    B:
    Ground clearance of lower suspension arm No. 1 set bolt center
    C:
    Ground clearance of rear wheel center
    D:
    Ground clearance of strut rod set bolt center

    1. If the vehicle height is not as specified, press down on the vehicle several times to stabilize the suspension. Then measure the vehicle height again.

    NOTICE:
    The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.



3. INSPECT TOE-IN


SA03213E04

Standard Toe-in (Unloaded Vehicle):
Vehicle Model
A + B
C - D
KUN51L-IKMSY
A + B: 0°1' +/-5' (0.01° +/-0.09°)
C - D: 0.4 +/-1.0 mm (0.02 +/-0.04 in.)
KUN51L-IKPSY
A + B: 0°1' +/-5' (0.01° +/-0.09°)
C - D: 0.1 +/-1.0 mm (0.01 +/-0.04 in.)
GGN50L-IKMSK
A + B: 0°1' +/-5' (0.02° +/-0.09°)
C - D: 0.6 +/-1.0 mm (0.02 +/-0.04 in.)
GGN50L-IKASK
A + B: 0°1' +/-5' (0.02° +/-0.09°)
C - D: 0.5 +/-1.0 mm (0.02 +/-0.04 in.)
TGN61L-NKMDKG
A + B: 0°3' +/-5' (0.05° +/-0.09°)
C - D: 1.2 +/-1.0 mm (0.05 +/-0.04 in.)
TGN61L-NKMDGG
7-passenger
A + B: 0°2' +/-5' (0.04° +/-0.09°)
C - D: 1.1 +/-1.0 mm (0.04 +/-0.04 in.)
5-passenger
A + B: 0°3' +/-5' (0.05° +/-0.09°)
C - D: 1.2 +/-1.0 mm (0.05 +/-0.04 in.)
TGN61L-NKPDGG
A + B: 0°2' +/-5' (0.04° +/-0.09°)
C - D: 1.0 +/-1.0 mm (0.04 +/-0.04 in.)
KUN51L-NKMSYG
A + B: 0°1' +/-5' (0.01° +/-0.09°)
C - D: 0.4 +/-1.0 mm (0.02 +/-0.04 in.)
KUN51L-NKPSYG
7-passenger
A + B: 0°1' +/-5' (0.01° +/-0.09°)
C - D: 0.2 +/-1.0 mm (0.01 +/-0.04 in.)
5-passenger
A + B: 0°1' +/-5' (0.01° +/-0.09°)
C - D: 0.1 +/-1.0 mm (0.01 +/-0.04 in.)
GGN50L-NKASKG
A + B: 0°1' +/-5' (0.02° +/-0.09°)
C - D: 0.4 +/-1.0 mm (0.02 +/-0.04 in.)
GGN50L-NKASKF
A + B: 0°1' +/-5' (0.02° +/-0.09°)
C - D: 0.5 +/-1.0 mm (0.02 +/-0.04 in.)
GGN50L-NKMSKF
A + B: 0°1' +/-5' (0.02° +/-0.09°)
C - D: 0.6 +/-1.0 mm (0.02 +/-0.04 in.)
KUN51L-NKMSYF
A + B: 0°1' +/-5' (0.01° +/-0.09°)
C - D: 0.4 +/-1.0 mm (0.02 +/-0.04 in.)
KUN51L-NKPSYF
A + B: 0°1' +/-5' (0.01° +/-0.09°)
C - D: 0.1 +/-1.0 mm (0.01 +/-0.04 in.)
TGN51L-NKMSKF
A + B: 0°1' +/-5' (0.02° +/-0.09°)
C - D: 0.5 +/-1.0 mm (0.02 +/-0.04 in.)
TGN51L-NKPSKF
A + B: 0°1' +/-5' (0.01° +/-0.09°)
C - D: 0.2 +/-1.0 mm (0.01 +/-0.04 in.)
TGN61L-NKMSKF
A + B: 0°3' +/-5' (0.05° +/-0.09°)
C - D: 1.3 +/-1.0 mm (0.05 +/-0.04 in.)
TGN61L-NKPSKF
A + B: 0°2' +/-5' (0.04° +/-0.09°)
C - D: 1.1 +/-1.0 mm (0.04 +/-0.04 in.)

  1. If the toe-in is not as specified, adjust it at the rack ends.


4. ADJUST TOE-IN
  1. Detach the rack boot set clips.

  1. Loosen the tie rod end lock nuts.

  1. Turn the right and left rack ends by an equal amount to adjust the toe-in to the center value.

    HINT:
    The toe-in should be as close as possible to the center value.



    F050367E01
  1. Make sure that the lengths of the right and left rack ends are approximately the same.

    Standard difference:
    0 +/-1 mm (0 +/-0.039 in.)

  1. Tighten the tie rod end lock nuts.

    Torque:
    55.5 N*m{ 566 kgf*cm , 41 ft.*lbf }

  1. Place the boots on the seats and attach the clips.

    HINT:
    Make sure that the boots are not twisted.



5. INSPECT WHEEL ANGLE


SA00028E06
  1. Turn the steering wheel to the left and right full lock positions, and measure the wheel angle.

    Standard Wheel Angle (Unloaded Vehicle):
    For All Tire Sizes except 265/65R17:
    Inside wheel angle
    Outside wheel angle (reference)
    36°18' (34°18' to 37°18')
    (36.3° {34.3° to 37.3°})
    33°12'
    (33.2°)
    For Tire Size 265/65R17:
    Inside wheel angle
    Outside wheel angle (reference)
    34°42' (32°42' to 35°42')
    (34.7° {32.7° to 35.7°})
    31°54'
    (31.9°)

    1. If the angles are not as specified, check and adjust the right and left rack end lengths.



6. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION


Z003382E06
  1. Install a camber-caster-kingpin gauge or place the front wheels on the center of a wheel alignment tester.

  1. Inspect the camber, caster and steering axis inclination.

    Standard Camber Inclination (Unloaded Vehicle):
    Vehicle Model
    Camber Inclination
    KUN51L-IKMSY
    Right-left error
    0°9' +/-30' (0.15° +/-0.50°)
    30' (0.50°) or less
    KUN51L-IKPSY
    Right-left error
    0°7' +/-30' (0.12° +/-0.50°)
    30' (0.50°) or less
    GGN50L-IKMSK
    Right-left error
    0°11' +/-30' (0.18° +/-0.50°)
    30' (0.50°) or less
    GGN50L-IKASK
    Right-left error
    0°10' +/-30' (0.17° +/-0.50°)
    30' (0.50°) or less
    TGN61L-NKMDKG
    Right-left error
    0°15' +/-30' (0.25° +/-0.50°)
    30' (0.50°) or less
    TGN61L-NKMDGG
    Right-left error
    0°15' +/-30' (0.25° +/-0.50°)
    30' (0.50°) or less
    TGN61L-NKPDGG
    Right-left error
    0°14' +/-30' (0.23° +/-0.50°)
    30' (0.50°) or less
    KUN51L-NKMSYG
    Right-left error
    0°9' +/-30' (0.15° +/-0.50°)
    30' (0.50°) or less
    KUN51L-NKPSYG
    Right-left error
    7-passenger
    0°8' +/-30' (0.13° +/-0.50°)
    30' (0.50°) or less
    5-passenger
    0°7' +/-30' (0.12° +/-0.50°)
    30' (0.50°) or less
    GGN50L-NKASKG
    Right-left error
    0°9' +/-30' (0.15° +/-0.50°)
    30' (0.50°) or less
    GGN50L-NKASKF
    Right-left error
    0°10' +/-30' (0.17° +/-0.50°)
    30' (0.50°) or less
    GGN50L-NKMSKF
    Right-left error
    0°11' +/-30' (0.18° +/-0.50°)
    30' (0.50°) or less
    KUN51L-NKMSYF
    Right-left error
    0°9' +/-30' (0.15° +/-0.50°)
    30' (0.50°) or less
    KUN51L-NKPSYF
    Right-left error
    0°7' +/-30' (0.12° +/-0.50°)
    30' (0.50°) or less
    TGN51L-NKMSKF
    Right-left error
    0°10' +/-30' (0.17° +/-0.50°)
    30' (0.50°) or less
    TGN51L-NKPSKF
    Right-left error
    0°8' +/-30' (0.13° +/-0.50°)
    30' (0.50°) or less
    TGN61L-NKMSKF
    Right-left error
    0°16' +/-30' (0.27° +/-0.50°)
    30' (0.50°) or less
    TGN61L-NKPSKF
    Right-left error
    0°15' +/-30' (0.25° +/-0.50°)
    30' (0.50°) or less

    Standard Caster Inclination (Unloaded Vehicle):
    Vehicle Model
    Caster Inclination
    KUN51L-IKMSY
    Right-left error
    2°52' +/-30' (2.87° +/-0.50°)
    30' (0.50°) or less
    KUN51L-IKPSY
    Right-left error
    2°54' +/-30' (2.90° +/-0.50°)
    30' (0.50°) or less
    GGN50L-IKMSK
    Right-left error
    2°56' +/-30' (2.93° +/-0.50°)
    30' (0.50°) or less
    GGN50L-IKASK
    Right-left error
    2°57' +/-30' (2.95° +/-0.50°)
    30' (0.50°) or less
    TGN61L-NKMDKG
    Right-left error
    2°55' +/-30' (2.92° +/-0.50°)
    30' (0.50°) or less
    TGN61L-NKMDGG
    Right-left error
    7-passenger
    2°56' +/-30' (2.93° +/-0.50°)
    30' (0.50°) or less
    5-passenger
    2°50' +/-30' (2.83° +/-0.50°)
    30' (0.50°) or less
    TGN61L-NKPDGG
    Right-left error
    7-passenger
    2°58' +/-30' (2.97° +/-0.50°)
    30' (0.50°) or less
    5-passenger
    2°52' +/-30' (2.87° +/-0.50°)
    30' (0.50°) or less
    KUN51L-NKMSYG
    Right-left error
    7-passenger
    2°55' +/-30' (2.92° +/-0.50°)
    30' (0.50°) or less
    5-passenger
    2°53' +/-30' (2.88° +/-0.50°)
    30' (0.50°) or less
    KUN51L-NKPSYG
    Right-left error
    7-passenger
    2°56' +/-30' (2.93° +/-0.50°)
    30' (0.50°) or less
    5-passenger
    2°54' +/-30' (2.90° +/-0.50°)
    30' (0.50°) or less
    GGN50L-NKASKG
    Right-left error
    2°57' +/-30' (2.95° +/-0.50°)
    30' (0.50°) or less
    GGN50L-NKASKF
    Right-left error
    2°57' +/-30' (2.95° +/-0.50°)
    30' (0.50°) or less
    GGN50L-NKMSKF
    Right-left error
    2°56' +/-30' (2.93° +/-0.50°)
    30' (0.50°) or less
    KUN51L-NKMSYF
    Right-left error
    2°52' +/-30' (2.87° +/-0.50°)
    30' (0.50°) or less
    KUN51L-NKPSYF
    Right-left error
    2°54' +/-30' (2.90° +/-0.50°)
    30' (0.50°) or less
    TGN51L-NKMSKF
    Right-left error
    2°53' +/-30' (2.88° +/-0.50°)
    30' (0.50°) or less
    TGN51L-NKPSKF
    Right-left error
    2°55' +/-30' (2.92° +/-0.50°)
    30' (0.50°) or less
    TGN61L-NKMSKF
    Right-left error
    2°50' +/-30' (2.83° +/-0.50°)
    30' (0.50°) or less
    TGN61L-NKPSKF
    Right-left error
    2°51' +/-30' (2.85° +/-0.50°)
    30' (0.50°) or less

    Standard Steering Axis Inclination (Unloaded Vehicle):
    Vehicle Model
    Steering Axis Inclination
    KUN51L-IKMSY
    Right-left error
    12°20' +/-30' (12.33° +/-0.50°)
    30' (0.50°) or less
    KUN51L-IKPSY
    Right-left error
    12°22' +/-30' (12.37° +/-0.50°)
    30' (0.50°) or less
    GGN50L-IKMSK
    Right-left error
    12°18' +/-30' (12.30° +/-0.50°)
    30' (0.50°) or less
    GGN50L-IKASK
    Right-left error
    12°19' +/-30' (12.32° +/-0.50°)
    30' (0.50°) or less
    TGN61L-NKMDKG
    Right-left error
    12°14' +/-30' (12.23° +/-0.50°)
    30' (0.50°) or less
    TGN61L-NKMDGG
    Right-left error
    12°14' +/-30' (12.23° +/-0.50°)
    30' (0.50°) or less
    TGN61L-NKPDGG
    Right-left error
    12°15' +/-30' (12.25° +/-0.50°)
    30' (0.50°) or less
    KUN51L-NKMSYG
    Right-left error
    12°20' +/-30' (12.33° +/-0.50°)
    30' (0.50°) or less
    KUN51L-NKPSYG
    Right-left error
    7-passenger
    12°21' +/-30' (12.35° +/-0.50°)
    30' (0.50°) or less
    5-passenger
    12°22' +/-30' (12.37° +/-0.50°)
    30' (0.50°) or less
    GGN50L-NKASKG
    Right-left error
    12°20' +/-30' (12.33° +/-0.50°)
    30' (0.50°) or less
    GGN50L-NKASKF
    Right-left error
    12°19' +/-30' (12.32° +/-0.50°)
    30' (0.50°) or less
    GGN50L-NKMSKF
    Right-left error
    12°18' +/-30' (12.30° +/-0.50°)
    30' (0.50°) or less
    KUN51L-NKMSYF
    Right-left error
    12°20' +/-30' (12.33° +/-0.50°)
    30' (0.50°) or less
    KUN51L-NKPSYF
    Right-left error
    12°22' +/-30' (12.37° +/-0.50°)
    30' (0.50°) or less
    TGN51L-NKMSKF
    Right-left error
    12°19' +/-30' (12.32° +/-0.50°)
    30' (0.50°) or less
    TGN51L-NKPSKF
    Right-left error
    12°21' +/-30' (12.35° +/-0.50°)
    30' (0.50°) or less
    TGN61L-NKMSKF
    Right-left error
    12°13' +/-30' (12.22° +/-0.50°)
    30' (0.50°) or less
    TGN61L-NKPSKF
    Right-left error
    12°14' +/-30' (12.23° +/-0.50°)
    30' (0.50°) or less

    1. If the camber and caster are not as specified, adjust them.
    1. If the steering axis inclination is not as specified after the camber and caster have been correctly adjusted, check the steering knuckle and front wheel for distortion or looseness.



7. ADJUST CAMBER AND CASTER

NOTICE:
After the camber has been adjusted, inspect the toe-in.

  1. Loosen the camber adjusting cam nut and camber adjusting cam bolt.

  1. Turn the No. 1 camber adjusting cam and No. 2 camber adjusting cam in both directions, and adjust the camber and caster to the center value.



  1. The camber and caster should be as close as possible to the center value.


    F049980E05



    C138176E01
  1. How to read the adjustment chart (using examples).

    1. Find the standard wheel alignment value applicable for the particular model.

    2. Mark the selected standard value on the adjustment chart.

      Standard value (reference):
      Camber
      Caster
      0°00' (0.00°)
      4°20' (4.33°)

    3. Mark the alignment value on the adjustment chart as measured when the vehicle is unloaded.

      Measured value (reference):
      Camber
      Caster
      0°10' (0.17°)
      3°50' (3.83°)



    4. As shown in the chart, read the distance from the marked point to 0, and adjust the front and/or rear adjusting cams accordingly.

      Amount to turn adjusting cams (by gradation):
      No. 1 camber adjusting cam
      No. 2 camber adjusting cam
      +3.0 mm
      -1.5 mm



      C113155E06



8. PLACE FRONT WHEELS FACING STRAIGHT AHEAD (w/ VSC)


9. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION (w/ VSC)
(Click here)