Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM (w/o Jam Protection Function)

POWER WINDOW CONTROL SYSTEM (w/o Jam Protection Function) > Rear Power Window RH does not Operate with Rear Power Window Switch RH

for Preparation Click here


DESCRIPTION

If the rear RH side manual UP / DOWN function does not operate, a malfunction may be present in the power window regulator motor, power window regulator switch, power window regulator master switch or wire harness.

WIRING DIAGRAM


B107968E28


INSPECTION PROCEDURE

1.CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH) (POWER SOURCE)
B107969E23
  1. Disconnect the P13 regulator switch connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    P13-3 - Body ground
    Ignition switch ON
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH)
B063163E03
  1. Remove the switch (Click here).

  1. Measure the resistance of the switch when the switch is operated.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 - 4
    2 - 3
    UP
    Below 1 Ω
    5 - 4
    2 - 1
    OFF
    Below 1 Ω
    5 - 3
    2 - 1
    DOWN
    Below 1 Ω



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY
OK


3.CHECK WIRE HARNESS (SWITCH (FOR REAR RH) - MOTOR (FOR REAR RH))

B111942E13

  1. Disconnect the P13 switch connector.

  1. Disconnect the P10 motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    P13-5 - P10-1
    Below 1 Ω
    P13-2 - P10-2
    Below 1 Ω
    P13-5 or P10-1 - Body ground
    10 kΩ or higher
    P13-2 or P10-2 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH)
B085064E01
  1. Remove the motor (Click here).

  1. Apply battery voltage to connector terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates counterclockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates clockwise



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY
OK


5.CHECK WIRE HARNESS (MASTER SWITCH - SWITCH (FOR REAR RH))

B111937E22

  1. Disconnect the P6 master switch connector.

  1. Disconnect the P13 switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    P6-10 (RRU) - P13-1
    Below 1 Ω
    P6-16 (RRD) - P13-4
    Below 1 Ω
    P6-10 (RRU) or P13-1 - Body ground
    10 kΩ or higher
    P6-16 (RRD) or P13-4 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (REAR RH SWITCH)
B059314E23
  1. Remove the master switch (Click here).

  1. Measure the resistance of the switch when the switch is operated.

    Standard resistance:

    Window Lock Switch Condition
    Power Window Switch Condition
    Tester Connection
    Specified Condition
    OFF
    UP
    3 (E) - 16 (RRD)
    6 (B) - 10 (RRU)
    Below 1 Ω
    OFF
    OFF
    3 (E) - 10 (RRU)
    3 (E) - 16 (RRD)
    Below 1 Ω
    OFF
    DOWN
    3 (E) - 10 (RRU)
    6 (B) - 16 (RRD)
    Below 1 Ω
    ON
    UP
    3 (E) - 16 (RRD)
    10 kΩ or higher
    6 (B) - 10 (RRU)
    Below 1 Ω
    ON
    OFF
    10 (RRU) - 16 (RRD)
    Below 1 Ω
    ON
    DOWN
    3 (E) - 10 (RRU)
    10 kΩ or higher
    6 (B) - 16 (RRD)
    Below 1 Ω



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK

GO TO POWER WINDOWS DO NOT OPERATE AT ALL