Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM (w/o Jam Protection Function)

POWER WINDOW CONTROL SYSTEM (w/o Jam Protection Function) > Rear Power Window LH does not Operate with Rear Power Window Switch LH

for Preparation Click here


DESCRIPTION

If the rear LH side manual UP / DOWN function does not operate, a malfunction may be present in the power window regulator motor, power window regulator switch, power window regulator master switch or wire harness.

WIRING DIAGRAM


B107968E27


INSPECTION PROCEDURE

1.CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH) (POWER SOURCE)
B107969E22
  1. Disconnect the P12 regulator switch connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    P12-3 - Body ground
    Ignition switch ON
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH)
B063163E03
  1. Remove the switch (Click here).

  1. Measure the resistance of the switch when the switch is operated.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 - 4
    2 - 3
    UP
    Below 1 Ω
    5 - 4
    2 - 1
    OFF
    Below 1 Ω
    5 - 3
    2 - 1
    DOWN
    Below 1 Ω



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY
OK


3.CHECK WIRE HARNESS (SWITCH (FOR REAR LH) - MOTOR (FOR REAR LH))

B111942E16

  1. Disconnect the P12 switch connector.

  1. Disconnect the P9 motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    P12-5 - P9-1
    Below 1 Ω
    P12-2 - P9-2
    Below 1 Ω
    P12-5 or P9-1 - Body ground
    10 kΩ or higher
    P12-2 or P9-2 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH)
B085065E01
  1. Remove the motor (Click here).

  1. Apply battery voltage to connector terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates clockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates counterclockwise



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY
OK


5.CHECK WIRE HARNESS (MASTER SWITCH - SWITCH (FOR REAR LH))

B111937E21

  1. Disconnect the P6 master switch connector.

  1. Disconnect the P12 switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    P6-12 (RLU) - P12-1
    Below 1 Ω
    P6-13 (RLD) - P12-4
    Below 1 Ω
    P6-12 (RLU) or P12-1 - Body ground
    10 kΩ or higher
    P6-13 (RLD) or P12-4 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (REAR LH SWITCH)
B059314E22
  1. Remove the master switch (Click here).

  1. Measure the resistance of the switch when the switch is operated.

    Standard resistance:

    Window Lock Switch Condition
    Power Window Switch Condition
    Tester Connection
    Specified Condition
    OFF
    UP
    3 (E) - 13 (RLD)
    6 (B) - 12 (RLU)
    Below 1 Ω
    OFF
    OFF
    3 (E) - 12 (RLU)
    3 (E) - 13 (RLD)
    Below 1 Ω
    OFF
    DOWN
    3 (E) - 12 (RLU)
    6 (B) - 13 (RLD)
    Below 1 Ω
    ON
    UP
    3 (E) - 13 (RLD)
    10 kΩ or higher
    6 (B) - 12 (RLU)
    Below 1 Ω
    ON
    OFF
    12 (RLU) - 13 (RLD)
    Below 1 Ω
    ON
    DOWN
    3 (E) - 12 (RLU)
    10 kΩ or higher
    6 (B) - 13 (RLD)
    Below 1 Ω



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK

GO TO POWER WINDOWS DO NOT OPERATE AT ALL