WASHER MOTOR > INSTALLATION |
| 1. INSTALL REAR WASHER MOTOR AND PUMP ASSEMBLY |
![]() |
Install the rear washer motor and pump to the packing of the washer jar.
| 2. INSTALL WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY |
![]() |
Install the windshield washer motor and pump to the packing of the washer jar.
| 3. INSTALL WINDSHIELD WASHER JAR ASSEMBLY |
![]() |
Install the windshield washer jar and pump with the 3 bolts. Then attach the 3 clamps.
Connect the 2 connector and 2 washer hoses.
Install the grommet.
| 4. FILL UP WASHER JAR AND PUMP ASSEMBLY WITH WASHER FLUID |
Fill the washer jar with washer fluid.
| 5. INSTALL FRONT BUMPER COVER |
w/ Headlight Cleaner System:
Connect the headlight cleaner hose.
w/ Fog Light:
Connect the 2 fog light connectors.
Attach the 8 claws to install the front bumper cover.
Install the 5 clips, 2 bolts and 2 screws.
Install the 3 clips and 6 screws.
| 6. INSTALL FOG LIGHT COVER RH (w/ Fog Light) |
| 7. INSTALL FOG LIGHT COVER LH (w/ Fog Light) |
Attach the 8 claws to install the fog light cover.
| 8. INSTALL FRONT BUMPER HOLE COVER RH (w/o Fog Light) |
| 9. INSTALL FRONT BUMPER HOLE COVER LH (w/o Fog Light) |
Attach the 8 claws to install the front bumper hole cover.
| 10. INSTALL RADIATOR GRILLE |
Attach the 6 claws to install the radiator grille.
Install the 2 screws and 2 clips.
| 11. INSTALL WASHER INLET SUB-ASSEMBLY |
![]() |
Install the washer inlet of the washer jar and pump to the windshield washer jar and pump.
![]() |
Install the washer inlet of the washer jar and pump with the clip.
| 12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 13. VEHICLE PREPARE FOR FOG LIGHT AIM ADJUSTMENT (w/ Fog Light) |
Prepare the vehicle:
| 14. PREPARE FOR FOG LIGHT AIMING (w/ Fog Light) |
![]() |
Prepare the vehicle:
| *a | 25 m or 3 m |
Prepare a piece of thick white paper that is approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width) to use as a screen.
Draw a vertical line down the center of the screen (V line).
Set the screen as shown in the illustration.

![]() |
Draw base lines (H line, V LH and V RH lines) on the screen as shown in the illustration.
| *a | V LH Line |
| *b | V Line |
| *c | V RH Line |
| *d | H Line |
| *e | Ground |
H Line (fog light height):
Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.
V LH Line, V RH Line (center mark position of LH and RH fog lights): Draw two vertical lines so that they intersect the H line at each center mark.
| 15. INSPECT FOG LIGHT AIMING (w/ Fog Light) |
Choose a headlight to inspect first. Cover or disconnect the connector of the other fog light to prevent light from that fog light from affecting the fog light aiming inspection.
Start the engine.
Turn on the fog lights and make sure that the cutoff line is within the specified area shown in the illustration.

| 16. ADJUST FOG LIGHT AIMING (w/ Fog Light) |
![]() |
Adjust the fog light aim so that it is within the specified range by turning the aiming screw with a screwdriver.
| *1 | Aiming Screw |