Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Seat Belt Warning Light for Passenger Seat does not Flash

for Preparation Click here


WIRING DIAGRAM


E236535E01


E236535E02


INSPECTION PROCEDURE

1.INSPECT FUSE (ECU-IG NO. 2*1 OR ECU-IG&GAUGE*2)
  1. *1: w/ Accessory meter
  2. *2: w/o Accessory meter
  1. Remove the ECU-IG NO. 2*1 fuse from the engine room relay block junction block.

  1. Remove the ECU-IG&GAUGE*2 fuse from the driver side junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


2.CHECK WIRE HARNESS (METER*1 OR LIGHT*2 - BATTERY AND GROUND)
E110289E14
  1. Disconnect the A42*1 meter connector.

  1. Disconnect the P23*2 light connector.

  1. *1: w/ Accessory meter
  2. *2: w/o Accessory meter
  1. Measure the voltage of the wire harness side connector.

    Standard Voltage:
    w/ Accessory meter 
    Tester Connection
    Condition
    Specified Condition
    A42-12 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    A42-12 (IG) - Body ground
    Ignition switch OFF
    Below 1 V

    w/o Accessory meter:
    Tester Connection
    Condition
    Specified Condition
    P23-3 - Body ground
    Ignition switch ON
    11 to 14 V
    P23-3 - Body ground
    Ignition switch OFF
    Below 1 V

  1. Measure the resistance of the wire harness side connector.

    Standard Resistance:
    w/ Accessory meter 
    Tester Connection
    Specified Condition
    A42-1 (GND1) - Body ground
    Below 1 Ω

    w/o Accessory meter:
    Tester Connection
    Specified Condition
    P23-1 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT FRONT SEAT INNER BELT ASSEMBLY (BUCKLE SWITCH)
B118978E01
  1. Disconnect the F12 belt connector.

  1. Measure the resistance of the buckle switch.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Seat belt is unfastened and more than 147 N (15 kgf, 33 lbf) of force is applied to occupant detection sensor
    Below 100 Ω
    1 - 2
    Seat belt is fastened and more than 147 N (15 kgf, 33 lbf) of force is applied to occupant detection sensor
    1 MΩ or higher



NG
Go to step 6
OK


4.CHECK WIRE HARNESS (INNER BELT - BODY GROUND)
E117164E03
  1. Disconnect the F12 belt connector.

  1. Measure the resistance of the wire harness side connector.

    Standard Resistance:
    Tester Connection
    Specified Condition
    F12-2 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK WIRE HARNESS (INNER BELT - METER*1 OR LIGHT*2)

E117529E12

  1. Disconnect the F12 belt connector.

  1. Disconnect the A42*1 meter connector.

  1. Disconnect the P23*2 light connector.

  1. *1: w/ Accessory meter
  2. *2: w/o Accessory meter
  1. Measure the resistance of the wire harness side connectors.

    Standard Resistance:
    w/ Accessory meter 
    Tester Connection
    Specified Condition
    F12-1 - A42-8 (PBEW)
    Below 1 Ω

    w/o Accessory meter:
    Tester Connection
    Specified Condition
    F12-1 - P23-2
    Below 1 Ω

Result 
Result
Proceed to
OK (w/ Accessory meter)
A
OK (w/o Accessory meter)
B
NG
C


B
REPLACE TELLTALE LIGHT ASSEMBLY

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ACCESSORY METER ASSEMBLY (MULTI-DISPLAY) 

6.INSPECT FRONT SEAT INNER BELT ASSEMBLY (OCCUPANT DETECTION SENSOR)
E169498E03
  1. Measure the resistance of the sensor.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Apply more than 147 N (15 kgf, 33 lbf) of force to occupant detection sensor
    Below 100 Ω
    1 - 2
    No force applied to occupant detection sensor
    1 MΩ or higher



NG
REPAIR FRONT SEAT CUSHION PAD
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY (FOR PASSENGER SIDE)