METER / GAUGE SYSTEM > Warning Buzzer does not Sound |

| 1.INSPECT FUSE (TAIL) |
Remove the TAIL fuse from the driver side junction block.
Measure the resistance of the fuse.
|
| ||||
| OK | |
| 2.CHECK COMBINATION METER ASSEMBLY (BUZZER OPERATION) |
Check the key reminder warning buzzer operation.
Turn the ignition switch OFF with the key inserted into the ignition key cylinder.
Open the driver side door.
Check the light reminder warning buzzer operation.
Turn the ignition switch OFF.
Set the light control switch to the TAIL or HEAD position.
Open the driver side door.
| Result | Proceed to |
| Key reminder warning buzzer does not sound | A |
| Light reminder warning buzzer does not sound | B |
|
| ||||
| A | |
| 3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY |
![]() |
Remove the unlock warning switch.
Measure the resistance of the switch.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Pushed (ON) | Below 1 Ω |
| 1 - 2 | Not pushed (OFF) | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK WIRE HARNESS (SWITCH - METER AND BODY GROUND) |
![]() |
Disconnect the U1 switch connector.
Disconnect the C26 meter connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| U1-1 - C26-10 | Below 1 Ω |
| U1-2 - Body ground | Below 1 Ω |
|
| ||||
| NG | ||
| ||
| 5.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (LIGHT CONTROL SWITCH) |
![]() |
Remove the headlight dimmer switch.
Measure the resistance of the switch.
| Tester Connection | Switch Condition | Specified Condition |
| 13 (B1) - 10 (T1) | HEAD | Below 1 Ω |
| 13 (B1) - 10 (T1) | TAIL | Below 1 Ω |
| 13 (B1) - 10 (T1) | OFF | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK WIRE HARNESS (SWITCH - METER AND BATTERY) |
![]() |
Disconnect the C12 switch connector.
Disconnect the C26 meter connector.
Measure the voltage of the wire harness side connectors.
| Tester Connection | Specified Condition |
| C12-13 (B1) - Body ground | 11 to 14 V |
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| C12-10 (T1) - C26-8 | Below 1 Ω |
|
| ||||
| OK | |
| 7.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (FOR DRIVER SIDE) |
![]() |
Remove the courtesy light switch.
Measure the resistance of the switch.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - Body ground | Not pushed (OFF) | Below 1 Ω |
| 1 - Body ground | Pushed (ON) | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.CHECK WIRE HARNESS (SWITCH - METER) |
![]() |
Disconnect the D4 switch connector.
Disconnect the C26 meter connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| D4-1 - C26-16 | Below 1 Ω |
|
| ||||
| OK | ||
| ||