METER / GAUGE SYSTEM > ON-VEHICLE INSPECTION |
| 1. CHECK SPEEDOMETER |
Check operation.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Standard Indication | Acceptable Range |
| 20 km/h | 21 to 25 km/h |
| 40 km/h | 41.7 to 46.2 km/h |
| 60 km/h | 62.7 to 67.2 km/h |
| 80 km/h | 83.4 to 88.4 km/h |
| 100 km/h | 104.3 to 109.3 km/h |
| 120 km/h | 125.1 to 130.6 km/h |
| 140 km/h | 145.8 to 151.8 km/h |
| 160 km/h | 166.2 to 173.2 km/h |
| 180 km/h | 186.9 to 194.5 km/h |
Check the deflection width of the speedometer indicator.
| 2. CHECK OUTPUT SIGNAL OF VEHICLE SPEED SENSOR |
![]() |
Check the output signal waveform.
Remove the combination meter, but do not disconnect the connector.
Using an oscilloscope, check the waveform of the combination meter.
| Item | Content |
| Tester Connection | C26-6 - C26-22 |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Vehicle Condition | Driving at approx. 20 km/h (12 mph) |
| 3. CHECK TACHOMETER |
Check operation.
Connect a tune-up test tachometer, and start the engine.
Compare the test tachometer values and vehicle tachometer values under the following conditions:
| Standard Tachometer Indication (rpm) | Acceptable Range (rpm) Data in ( ) are for reference only |
| 700 | 630 to 770 |
| 1,000 | (900 to 1100) |
| 2,000 | (1850 to 2150) |
| 3,000 | 2800 to 3200 |
| 4,000 | (3800 to 4200) |
| 5,000 | 4800 to 5200 |
| 4. CHECK FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY |
![]() |
Disconnect the F14*1 or F13*2 pump and gauge connector.
Turn the ignition switch ON, and then check the position of the receiver gauge needle.
Connect terminals 2 and 3 of the wire harness side connector.
Turn the ignition switch ON, and then check the position of the receiver gauge needle.
| 5. CHECK FUEL LEVEL WARNING LIGHT |
![]() |
Disconnect the F14*1 or F13*2 pump and gauge connector.
Turn the ignition switch ON, and then check that the fuel receiver gauge indicates E and that the fuel level warning light turns on.
| 6. CHECK LOW OIL PRESSURE WARNING LIGHT |
![]() |
Disconnect the E3 switch connector.
Connect terminal 1 of the wire harness side connector to the body ground.
Turn the ignition switch ON, and then check that the low oil pressure warning light turns on.
| 7. CHECK BRAKE WARNING LIGHT |
![]() |
Check the parking brake warning light.
Disconnect the P3 switch connector.
Connect terminal 1 of the wire harness side connector to the body ground.
Turn the ignition switch ON, and then check that the warning light turns on.
![]() |
Check the brake fluid level warning light.
Disconnect the B2 switch connector.
Connect terminals 1 and 2 of the wire harness side connector.
Turn the ignition switch ON, and then check that the warning light turns on.
1KD-FTV:
Check the vacuum pump warning light.
Disconnect the B3 switch connector.
Connect terminal 1 of the wire harness side connector to the body ground.
Turn the ignition switch ON, and then check that the warning light turns on.
| 8. CHECK SEAT BELT WARNING LIGHT FOR PASSENGER SIDE |
![]() |
Disconnect the F12 switch connector.
Connect terminals 1 and 2 of the wire harness side connector.
Turn the ignition switch ON, and then check that the warning light blinks.