POWER DOOR LOCK CONTROL SYSTEM > All Doors cannot be Locked / Unlocked Simultaneously |


| 1.CHECK DOOR LOCK / UNLOCK OPERATION |
Proceed to the next step according to the system listed in the table below.
| Symptom | Proceed to |
| All doors cannot be locked / unlocked at once using door control switch on master switch (switch operation) | A |
| All doors cannot be locked / unlocked at once using door key cylinder on driver side (key operation) | B |
| Only one door cannot be locked / unlocked | C |
| All symptoms listed above are present | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH (DOOR CONTROL SWITCH) |
![]() |
Measure the resistance of the door control switch.
| Tester Connection | Switch Condition | Specified Condition |
| 5 - 3 | Lock | Below 1 Ω |
| 5 - 3, 8- 3 | OFF | 10 kΩ or higher |
| 8 - 3 | Unlock | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| 5 - 1 | Lock | Below 1 Ω |
| 5 - 1, 8- 1 | OFF | 10 kΩ or higher |
| 8 - 1 | Unlock | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK WIRE HARNESS (MASTER SWITCH - INTEGRATION RELAY AND BODY GROUND) |
![]() |
Disconnect the P6 switch connector.
Disconnect the 2A and 2D integration relay connectors.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| P6-5 - 2A-4 (L1) | Below 1 Ω |
| P6-8 - 2D-4 (UL1) | Below 1 Ω |
| P6-3 - Body ground | Below 1 Ω |
| P6-5 or 2A-4 (L1) - Body ground | 10 kΩ or higher |
| P6-8 or 2D-4 (UL1) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| P6-5 - 2A-4 (L1) | Below 1 Ω |
| P6-8 - 2D-4 (UL1) | Below 1 Ω |
| P6-1 - Body ground | Below 1 Ω |
| P6-5 or 2A-4 (L1) - Body ground | 10 kΩ or higher |
| P6-8 or 2D-4 (UL1) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 4.INSPECT FRONT DOOR LOCK (DRIVER SIDE DOOR LOCK AND UNLOCK SWITCH) |
![]() |
Measure the resistance of the door lock and unlock switch.
| Tester Connection | Door Lock Condition | Specified Condition |
| 9 - 7 | Lock | Below 1 Ω |
| 9 - 7, 10 - 7 | OFF | 10 kΩ or higher |
| 10 - 7 | Unlock | Below 1 Ω |
|
| ||||
| OK | |
| 5.INSPECT FRONT SEAT INNER BELT (FOR DRIVER SIDE) |
![]() |
for Power Seat:
Measure the resistance of the buckle switch.
| Tester Connection | Condition | Specified Condition |
| 1 - 4 | Seat belt is unfastened | Below 1 Ω |
| 1 - 4 | Seat belt is fastened | 1 MΩ or higher |
![]() |
for Manual Seat:
Measure the resistance of the buckle switch.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Seat belt is unfastened | Below 1 Ω |
| 1 - 2 | Seat belt is fastened | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK WIRE HARNESS (DRIVER SIDE DOOR LOCK - INTEGRATION RELAY AND BODY GROUND) |
![]() |
Disconnect the D8 door lock connector.
Disconnect the 2A and 2D integration relay connectors.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
| D8-10 - 2D-4 (UL1) | Always | Below 1 Ω |
| D8-9 - 2A-4 (L1) | Always | Below 1 Ω |
| D8-7 - Body ground | Driver seat belt is unfastened | Below 1 Ω |
| D8-10 or 2D-4 (UL1) - Body ground | Always | 10 kΩ or higher |
| D8-9 or 2A-4 (L1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 7.INSPECT DOOR LOCK (DRIVER SIDE, PASSENGER SIDE, REAR LH, REAR RH AND BACK DOOR) |

Apply battery voltage to the door lock and check the operation of the door lock motor.
| Measurement Condition | Specified Condition |
| Battery positive (+) → Terminal 4 Battery negative (-) → Terminal 1 | Lock |
| Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 4 | Unlock |
| Measurement Condition | Specified Condition |
| Battery positive (+) → Terminal 4 Battery negative (-) → Terminal 3 | Lock |
| Battery positive (+) → Terminal 3 Battery negative (-) → Terminal 4 | Unlock |
|
| ||||
| OK | |
| 8.CHECK WIRE HARNESS (DOOR LOCK - INTEGRATION RELAY AND BODY GROUND) |
![]() |
Disconnect the D8, D9, D10 and D11 door lock connectors.
Disconnect the B9 back door lock connector.
Disconnect the 2K and 2R integration relay connectors.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| D8-4 - 2R-28 (ACT+) | Below 1 Ω |
| D8-1 - 2R-27 (ACT-) | Below 1 Ω |
| D9-4 - 2K-11 (ACT+) | Below 1 Ω |
| D9-1 - 2K-10 (ACT-) | Below 1 Ω |
| D10-4 - 2R-28 (ACT+) | Below 1 Ω |
| D10-1 - 2R-27 (ACT-) | Below 1 Ω |
| D11-4 - 2K-11 (ACT+) | Below 1 Ω |
| D11-1 - 2K-10 (ACT-) | Below 1 Ω |
| B9-4 - 2K-11 (ACT+) | Below 1 Ω |
| B9-3 - 2K-10 (ACT-) | Below 1 Ω |
| D8-4 or 2R-28 (ACT+) - Body ground | 10 kΩ or higher |
| D8-1 or 2R-27 (ACT-) - Body ground | 10 kΩ or higher |
| D9-4 or 2K-11 (ACT+) - Body ground | 10 kΩ or higher |
| D9-1 or 2K-10 (ACT-) - Body ground | 10 kΩ or higher |
| D10-4 or 2R-28 (ACT+) - Body ground | 10 kΩ or higher |
| D10-1 or 2R-27 (ACT-) - Body ground | 10 kΩ or higher |
| D11-4 or 2K-11 (ACT+) - Body ground | 10 kΩ or higher |
| D11-1 or 2K-10 (ACT-) - Body ground | 10 kΩ or higher |
| B9-4 or 2K-11 (ACT+) - Body ground | 10 kΩ or higher |
| B9-3 or 2K-10 (ACT-) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 9.INSPECT FUSE (ECU-B, DCC, DOOR) |
Remove the ECU-B and DCC fuses from the engine room relay block.
Remove the DOOR fuse from the No. 3 relay block.
Measure the resistance of the fuses.
|
| ||||
| OK | |
| 10.CHECK WIRE HARNESS (INTEGRATION RELAY - BATTERY AND BODY GROUND) |
![]() |
Disconnect the 2D, 2H and 2L integration relay connectors.
Measure the voltage and resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| 2L-12 (BECU) - Body ground | 11 to 14 V |
| 2H-4 (ALTB) - Body ground | 11 to 14 V |
| Tester Connection | Specified Condition |
| 2D-9 (GND) - Body ground | Below 1 Ω |
| 2D-18 (GND) - Body ground | Below 1 Ω |
|
| ||||
| OK | |
| 11.CHECK WIRE HARNESS (MASTER SWITCH - INTEGRATION RELAY AND BODY GROUND) |
![]() |
Disconnect the P6 switch connector.
Disconnect the 2A and 2D integration relay connectors.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| P6-5 - 2A-4 (L1) | Below 1 Ω |
| P6-8 - 2D-4 (UL1) | Below 1 Ω |
| P6-3 - Body ground | Below 1 Ω |
| P6-5 or 2A-4 (L1) - Body ground | 10 kΩ or higher |
| P6-8 or 2D-4 (UL1) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| P6-5 - 2A-4 (L1) | Below 1 Ω |
| P6-8 - 2D-4 (UL1) | Below 1 Ω |
| P6-1 - Body ground | Below 1 Ω |
| P6-5 or 2A-4 (L1) - Body ground | 10 kΩ or higher |
| P6-8 or 2D-4 (UL1) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||