Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)

AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the radio receiver assembly and steering pad switch LH illumination when the light control switch is in the TAIL or HEAD position.

WIRING DIAGRAM


C240217E06


INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the SRS (Click here).

1.CHECK ILLUMINATION
  1. Check if the illumination for the radio receiver assembly, steering pad switch LH, glove box or other parts (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.
    Result 
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch LH.
    A
    Illumination comes on for all components except radio receiver assembly.
    B
    No illumination comes on (radio receiver assembly, hazard switch, glove box, etc.).
    C



B
Go to step 6

C
GO TO LIGHTING SYSTEM (Click here)
A


2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BATTERY)


    E198671E10
  1. Disconnect the S28 spiral cable sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S28-12 (IL+2) - Body ground
    Light control switch TAIL or HEAD
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Spiral Cable Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT STEERING PAD SWITCH LH


  1. Remove the steering pad switch LH (Click here).


    C237716E03

  1. Connect the positive (+) lead of the battery to terminal 5 (ILL+) and the negative (-) lead to terminal 8 (EAU) of the steering pad switch LH connector.

  1. Check if the illumination for the steering pad switch LH comes on.

    OK:
    Illumination for the steering pad switch LH comes on.



NG
REPLACE STEERING PAD SWITCH LH (Click here)
OK


4.INSPECT SPIRAL CABLE SUB-ASSEMBLY


    C237983E09
  1. Remove the spiral cable sub-assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    8 (EAU) - 4 (EAU)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    5 (ILL+) - 12 (IL+2)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise

    Text in Illustration 
    *a
    Steering Pad Switch Side
    *b
    Vehicle Side

    CAUTION:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS (Click here).



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - SPIRAL CABLE)
  1. Disconnect the R34 radio receiver assembly connector.

  1. Disconnect the S28 spiral cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R34-23 (SWG) - S28-4 (EAU)
    Always
    Below 1 Ω
    R34-23 (SWG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - BATTERY AND BODY GROUND)


    E178447E34
  1. Disconnect the R2 radio receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R2-7 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R2-10 (ILL+) - Body ground
    Light control switch TAIL or HEAD
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Radio Receiver Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)