NAVIGATION SYSTEM > Illumination Circuit |

| 1.CHECK ILLUMINATION |
Check if the illumination for the navigation receiver assembly, steering pad switch assembly, glove box or other parts (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.
| Result | Proceed to |
| Illumination comes on for all components except steering pad switch assembly. | A |
| Illumination comes on for all components except navigation receiver assembly. | B |
| No illumination comes on (navigation receiver assembly, hazard switch, glove box, etc.). | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY) |
![]() |
Disconnect the S28 spiral cable sub-assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| S28-12 (IL+2) - Body ground | Light control switch TAIL or HEAD | 11 to 14 V |
| *a | Front view of wire harness connector (to Spiral Cable Sub-assembly) |
|
| ||||
| OK | |
| 3.INSPECT STEERING PAD SWITCH ASSEMBLY |
Remove the steering pad switch assembly (Click here).

Connect the positive (+) lead of the battery to terminal 5 (IL+2) and the negative (-) lead to terminal 8 (EAU) of the steering pad switch assembly connector.
Check if the illumination for the steering pad switch assembly comes on.
|
| ||||
| OK | |
| 4.INSPECT SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Remove the spiral cable sub-assembly (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 8 (EAU) - 4 (EAU) | Spiral cable is turned 2.5 rotations counterclockwise | Below 1 Ω |
| Spiral cable is centered | ||
| Spiral cable is turned 2.5 rotations clockwise | ||
| 5 (IL+2) - 12 (IL+2) | Spiral cable is turned 2.5 rotations counterclockwise | |
| Spiral cable is centered | ||
| Spiral cable is turned 2.5 rotations clockwise |
| *a | Steering Pad Switch Side |
| *b | Vehicle Side |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY) |
Disconnect the N5 navigation receiver assembly connector.
Disconnect the S28 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N5-23 (SWG) - S28-4 (EAU) | Always | Below 1 Ω |
| N5-23 (SWG) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND) |
![]() |
Disconnect the N8 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N8-7 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| N8-10 (ILL+) - Body ground | Light control switch TAIL or HEAD | 11 to 14 V |
| *a | Front view of wire harness connector (to Navigation Receiver Assembly) |
|
| ||||
| OK | ||
| ||