AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) > Illumination Circuit |

| 1.CHECK ILLUMINATION |
Check if the illumination for the radio receiver assembly, steering pad switch LH, glove box or other parts (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.
| Result | Proceed to |
| Illumination comes on for all components except steering pad switch LH. | A |
| Illumination comes on for all components except radio receiver assembly. | B |
| No illumination comes on (radio receiver assembly, hazard switch, glove box, etc.). | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BATTERY) |
![]() |
Disconnect the S28 spiral cable sub-assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| S28-12 (IL+2) - Body ground | Light control switch TAIL or HEAD | 11 to 14 V |
| *a | Front view of wire harness connector (to Spiral Cable Sub-assembly) |
|
| ||||
| OK | |
| 3.INSPECT STEERING PAD SWITCH LH |
Remove the steering pad switch LH (Click here).

Connect the positive (+) lead of the battery to terminal 5 (ILL+) and the negative (-) lead to terminal 8 (EAU) of the steering pad switch LH connector.
Check if the illumination for the steering pad switch LH comes on.
|
| ||||
| OK | |
| 4.INSPECT SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Remove the spiral cable sub-assembly (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 8 (EAU) - 4 (EAU) | Spiral cable is turned 2.5 rotations counterclockwise | Below 1 Ω |
| Spiral cable is centered | ||
| Spiral cable is turned 2.5 rotations clockwise | ||
| 5 (ILL+) - 12 (IL+2) | Spiral cable is turned 2.5 rotations counterclockwise | |
| Spiral cable is centered | ||
| Spiral cable is turned 2.5 rotations clockwise |
| *a | Steering Pad Switch Side |
| *b | Vehicle Side |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - SPIRAL CABLE) |
Disconnect the R34 radio receiver assembly connector.
Disconnect the S28 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R34-23 (SWG) - S28-4 (EAU) | Always | Below 1 Ω |
| R34-23 (SWG) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - BATTERY AND BODY GROUND) |
![]() |
Disconnect the R2 radio receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R2-7 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| R2-10 (ILL+) - Body ground | Light control switch TAIL or HEAD | 11 to 14 V |
| *a | Front view of wire harness connector (to Radio Receiver Assembly) |
|
| ||||
| OK | ||
| ||