Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Radio Broadcast cannot be Received or Poor Reception


WIRING DIAGRAM


E278320E10


INSPECTION PROCEDURE

1.CHECK NAVIGATION RECEIVER ASSEMBLY
  1. Check the radio automatic station search function.

    1. Check the radio automatic station search function by activating it.
      Result 
      Result
      Proceed to
      Automatic station search function does not stop
      A
      Automatic station search function stops on a station
      B



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
A


2.CHECK OPTIONAL COMPONENTS
  1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.
    Result 
    Result
    Proceed to
    Optional components are not installed
    A
    Optional components are installed
    B

    NOTICE:
    Do not remove optional components without the permission of the customer.



B
REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)
A


3.CHECK NAVIGATION RECEIVER ASSEMBLY


    E245523
  1. Preparation for check

    1. Disconnect the antenna connector from the navigation receiver assembly.

  1. Check for noise

    1. Turn the ignition switch to ACC with the navigation receiver assembly connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speakers.

      OK:
      Noise can be heard from the speakers.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


4.CHECK WINDOW GLASS ANTENNA WIRE


    E111994E18
  1. Check for continuity in the window glass antenna wire.

    HINT:
    Check for continuity at the center of each antenna wire as shown in the illustration.

    NOTICE:
    When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger as shown in the illustration.

    OK:
    There is continuity in the window glass antenna wire.

    Text in Illustration 
    *a
    Tester Probe
    *b
    Antenna Wire
    *c
    Tin Foil



NG
REPAIR WINDOW GLASS ANTENNA WIRE
OK


5.INSPECT NAVIGATION RECEIVER ASSEMBLY
  1. Disconnect the navigation receiver assembly connector.



    E188455E38
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    5 (ANT+) - Body ground
    Ignition switch ACC
    Radio switch on and AM or FM selected
    11 to 14 V



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


6.CHECK ANTENNA CORD SUB-ASSEMBLY


    E278669E01
  1. Disconnect the navigation receiver assembly connector.

  1. Disconnect the antenna connector from the amplifier antenna assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    RA-3 (MAIN) - 2
    Always
    Below 1 Ω
    RA-5 (ANT+) - 3
    Always
    Below 1 Ω
    RA-3 (MAIN) - Body ground
    Always
    10 kΩ or higher
    RA-5 (ANT+) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Navigation Receiver Assembly)
    *b
    Front view of wire harness connector
    (to Amplifier Antenna Assembly)



NG
REPLACE ANTENNA CORD SUB-ASSEMBLY (Click here)
OK


7.CHECK AMPLIFIER ANTENNA ASSEMBLY
  1. Replace the amplifier antenna assembly (Click here).

  1. Check if radio broadcasts can be received normally.

    OK:
    Radio broadcasts can be received normally.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

END (AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)