Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › COMPRESSOR (for 1GR-FE)

COMPRESSOR (for 1GR-FE) > INSTALLATION

for Preparation Click here



1. ADJUST COMPRESSOR OIL
  1. When replacing the compressor and magnet clutch with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new compressor and magnet clutch before installation.

    Standard:
    (Oil capacity inside the new compressor and magnet clutch: 180 + 15 cc (6.08 + 0.51 fl.oz.)) - (Remaining oil amount in the removed compressor and magnet clutch) = (Oil amount to be removed from the new compressor)

    NOTICE:
    1. When checking the compressor oil level, follow the A/C system precautions.
    2. If a new compressor and magnet clutch is installed without removing the oil remaining in the pipes of the vehicle, the oil amount will be too large. This prevents heat exchange in the refrigerant cycle and causes refrigerant failure.
    3. If the volume of oil remaining in the removed compressor and magnet clutch is small, check for oil leakage.
    4. Be sure to use ND-OIL 8 or equivalent compressor oil.



2. INSTALL COOLER COMPRESSOR ASSEMBLY


    E174571
  1. Install the compressor with the 4 bolts and tighten the bolts in the order shown in the illustration.

    Torque:
    24.5 N*m{ 250 kgf*cm , 18 ft.*lbf }



    E174570
  1. Connect the connector.



3. INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE


    E174569
  1. Remove the vinyl tape attached to the hose.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring to the discharge hose.

  1. Connect the discharge hose with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }



4. INSTALL SUCTION HOSE SUB-ASSEMBLY


    E174568
  1. Remove the vinyl tape attached to the hose.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring to the suction hose.

  1. Connect the suction hose with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }



5. INSTALL DRIVE BELT


    A076442E01
  1. While turning the belt tensioner counterclockwise, align its holes, and then insert a bar of 6.0 mm (0.24 in.) into the holes to fix the belt tensioner.

  1. Install the V-ribbed belt.

  1. While turning the belt tensioner counterclockwise, remove the bar.



  1. If it is hard to install the V-ribbed belt, perform the following procedure.



      A113028E02
    1. Put the V-ribbed belt on everything except the P/S pump as shown in the illustration.

    2. While releasing the belt tension by turning the belt tensioner counterclockwise, put the V-ribbed belt on the P/S pump.



6. CHARGE REFRIGERANT
SST
09985-20010   (09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070)
  1. Perform vacuum purging using a vacuum pump.



  1. Charge refrigerant HFC-134a (R134a).

    Standard:
    750 +-30 g (26.45 +-1.05 oz.)



    I037365E02

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor will not work properly without any refrigerant, and will overheat.
    1. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by quantity, and not with the sight glass.



7. WARM UP ENGINE
  1. Warm up the engine at less than 1,850 rpm for 2 minutes or more after charging refrigerant.

    NOTICE:
    Be sure to warm up the compressor when turning the A/C switch ON after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.



8. CHECK FOR LEAKAGE OF REFRIGERANT
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation under these conditions:

    1. Stop the engine.
    1. Secure good ventilation (the gas leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    1. Repeat the test 2 or 3 times.
    1. Make sure that some refrigerant remains in the refrigeration system. When compressor is off: approximately 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)



    I042222E02
  1. Using a gas leak detector, check the refrigerant line for leakage.

  1. If a gas leak is not detected on the drain hose, remove the blower motor control (blower resistor) from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.

  1. Disconnect the connector and leave the pressure switch on for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.