ECD SYSTEM > SYSTEM DESCRIPTION |
| ENGINE CONTROL SYSTEM |

| *1 | ECM | *2 | Atmospheric Pressure Sensor |
| *3 | Accelerator Pedal Position Sensor | *4 | Ignition Switch Signal |
| *5 | Starter Signal | *6 | Vehicle Speed Signal |
| *7 | DLC3 | *8 | Battery Voltage |
| *9 | Stop Light Switch | *10 | Other Signal |
| *11 | Fuel Tank | *12 | Suction Control Valve |
| *13 | Fuel Temperature Sensor | *14 | Fuel Supply Pump Assembly |
| *15 | Generator | *16 | Fuel Pressure Sensor |
| *17 | Pressure Discharge Valve | *18 | Common Rail Assembly |
| *19 | Injector Driver | *20 | EDU Relay |
| *21 | Diesel Throttle Body Assembly | *22 | Manifold Absolute Pressure Sensor |
| *23 | Mass Air Flow Meter | *24 | Intake Air Temperature Sensor (Built Into Mass Air Flow Meter) |
| *25 | Injector Assembly | *26 | EGR Valve Position Sensor |
| *27 | Electric Vacuum Regulating Valve Assembly | *28 | Turbocharger Sub-Assembly |
| *29 | Engine Coolant Temperature Sensor | *30 | Camshaft Position Sensor |
| *31 | Crankshaft Position Sensor | *32 | Glow Plug Relay (GLOW) |
| *33 | Glow Plug | *34 | Vacuum Pump |
| COMMON RAIL SYSTEM DESCRIPTION |

| Component | Description |
| Common rail | Stores high-pressure fuel produced by supply pump |
| Supply pump | Operated by crankshaft. Supplies high-pressure fuel to common rail. |
| Injector | Injects fuel to combustion chamber based on signals from ECM |
| Fuel pressure sensor | Monitors internal fuel pressure of common rail and sends signals to ECM |
| Pressure discharge valve | Based on signals from the ECM, opens valve when sudden deceleration is occurred, or when the ignition switch is OFF to prevent the fuel pressure from becoming too high. |
| Suction control valve | Based on signals from ECM, adjusts fuel volume supplied to common rail and regulates internal fuel pressure |
| Trouble Area | Malfunction | DTC No. |
| Injector | Open or short in injector circuit | P0200, P0093* |
| Stuck open | P0093 | |
| Stuck closed | - | |
| Fuel pressure sensor | Open or short in fuel pressure sensor circuit or pressure sensor output fixed | P0087, P0190, P0191, P0192, P0193 |
| Pressure discharge valve | Open or short in pressure discharge valve circuit | P1271, P1272, P0088*, P0093*, P1229* |
| Stuck open | P0093 | |
| Stuck closed | P1272, P0088* | |
| Suction control valve | Open or short in suction control valve circuit | P0627, P1229, P0088* |
| Stuck open | P1229, P0088* | |
| Stuck closed | - | |
| EDU | Faulty EDU | P0093*, P0200*, P1271*, P1272* |
| Common rail system (Fuel system) | Fuel leaks in high-pressure areas | P0093 |
| DTC No. | Description | |
| P0087 | Fuel pressure sensor output does not change | |
| P0088 | Internal fuel pressure too high (200000 kPa [2039 kgf/cm2, 29007 psi] or more) | |
| P0093 | Fuel leaks in high-pressure areas | |
| P0190 | Open or short in fuel pressure sensor circuit (Low or high output) | |
| P0191 | Fuel pressure sensor out of range (Low output) | |
| P0192 | Open or short in fuel pressure sensor circuit (High output) | |
| P0193 | Open or short in fuel pressure sensor circuit (Sensor 1 and/or 2 relation) | |
| P0200 | Open or short in EDU or injector circuit | |
| P0627 | Open or short in suction control valve circuit | |
| P1229 | Fuel over-feed | |
| P1271 | Open or short in pressure discharge valve circuit | |
| P1272 | Closed malfunction of the pressure discharge valve | |
| INJECTION CONTROL SYSTEM DESCRIPTION |

| SUPPLY PUMP OPERATION SYSTEM DESCRIPTION |

| SUCTION CONTROL VALVE OPERATION SYSTEM DESCRIPTION |
Small opening of the suction control valve:
When the opening of the suction control valve is small, the fuel suction path is kept narrow. Therefore the transferable fuel volume is reduced (*A).
The suction volume becomes small due to the narrow path despite the plunger stroke being full. The difference between the geometrical volume and suction volume creates a vacuum (*B).
Pumping will start when the fuel pressure becomes higher than the common rail pressure (*C).

Large opening of the suction control valve:
When the opening of the suction control valve is large, the fuel suction path is kept wide. Therefore the transferable fuel volume is increased (*D).
If the plunger stroke is full, the suction volume becomes large because of the wide path (*E).
Pumping will start when the fuel pressure becomes higher than the common rail pressure (*F).
