ECD SYSTEM (for i-ART) > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List.
Check the values by referring to the table below.
| i-ART System |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| i-ART Learning Status #1 i-ART Learning Status #2 i-ART Learning Status #3 i-ART Learning Status #4 | i-ART learning status/ OK or NG | OK: Normal | Calculated value |
|
| Symptoms when out of range: Rough idle, black smoke, white smoke, poor drivability, insufficient output, knocking and engine starting trouble | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| i-ART Learning Status History #1 i-ART Learning Status History #2 i-ART Learning Status History #3 i-ART Learning Status History #4 | i-ART learning status history/ Min.: 0 Trip, Max.: 255 Trip | 0 Trip | Calculated value |
|
| Symptoms when out of range: Rough idle, black smoke, white smoke, poor drivability, insufficient output, knocking and engine starting trouble | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Injector Leaking Count #1 Injector Leaking Count #2 Injector Leaking Count #3 Injector Leaking Count #4 | Injector leaking count/ Min.: 0, Max.: 255 | 0 | Calculated value |
|
| Symptoms when out of range: Rough idle, black smoke, white smoke, poor drivability, insufficient output, knocking and engine starting trouble | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Pre Injection Period | Pre injection period/ Min.: 0 μs, Max.: 65535 μs | 100 to 400 μs: After the engine is warmed up, the engine is idling and the vehicle is under normal atmospheric pressure (During triple pilot) | Calculated value | - |
| Symptoms when out of range: Combustion noise, poor driveability, white smoke | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Pre Injection Timing | Pre Injection Timing/ Min.: -3276.8 °CA, Max.: 3276.8 °CA | -13.2 to -9.2°CA: After the engine is warmed up, the engine is idling and the vehicle is under normal atmospheric pressure (During triple pilot) | Calculated value | - |
| Symptoms when out of range: Combustion noise, poor driveability, white smoke | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Total Injection Volume | Total injection volume/ Min.: -640 mm3/st, Max.: 640 mm3/st | Idling: 2.0 to 11 mm3/st | Calculated value | - |
| Symptoms when out of range: Combustion noise, poor driveability, white smoke | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Injection Volume #1 Injection Volume #2 Injection Volume #3 Injection Volume #4 | Injection volume/ Min.: -640 mm3/st, Max.: 640 mm3/st | Idling: 2.0 to 11 mm3/st | Calculated value | - |
| Symptoms when out of range: Combustion noise, poor driveability, white smoke | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Fuel Pressure #1 Fuel Pressure #2 Fuel Pressure #3 Fuel Pressure #4 | Fuel pressure/ Min.: 0 kPa, Max.: 250000 kPa | Idling: 30000 to 50000 kPa | Sensor output (fuel pressure sensor (injector assembly)) |
|
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Fuel Temperature #1 Fuel Temperature #2 Fuel Temperature #3 Fuel Temperature #4 | Fuel temperature/ Min.: -40°C, Max.: 140°C | Idling after engine warmed-up: 35 to 85°C (95 to 185°F) | Sensor output (fuel temperature sensor) | - |
Diagnostic Note:
| ||||
| Engine Control |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Calculate Load | Load calculated by ECM/ Min.: 0%, Max.: 100% |
| Calculated by ECM | Malfunction in which turbo pressure or Mass Air Flow decreases |
| Diagnostic Note: Calculated load = (Final injection volume / max. injection volume at current engine speed) x 100. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| MAF | Air flow rate from mass air flow meter/ Min.: 0 gm/s, Max.: 400 gm/s |
| Sensor output (mass air flow meter) |
|
| Symptoms when out of range: Rough idling | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Engine Speed | Engine speed/ Min.: 0 rpm, Max.: 6000 rpm |
| Sensor output (crankshaft position sensor) |
|
| Diagnostic Note: When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Target Idle Engine Speed | Target idling engine speed/ Min.: 0 rpm, Max.: 10000 rpm | - | Target idling speed (ECM calculated value) | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| MAP | Absolute pressure inside intake manifold/ Min.: 0 kPa, Max.: 320 kPa |
| Sensor output (manifold absolute pressure sensor) |
|
| Symptoms when out of range: Lack of power | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Vehicle Speed | Vehicle speed/ Min.: 0 km/h, Max.: 255 km/h | Actual vehicle speed | Sensor output (speed sensor) |
|
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Coolant Temp | Engine coolant temperature/ Min.: -40°C, Max.: 140°C | After warming up engine: 70 to 90°C (158 to 194°F) | Sensor output (engine coolant temperature sensor) |
|
| Symptoms when out of range: Difficulty starting when engine is cold, rough idle, black smoke, lack of power | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Intake Air | Intake air temperature/ Min.: -40°C, Max.: 140°C | Equivalent to temperature at location of mass air flow meter | Sensor output (intake air temperature sensor (built into mass air flow meter)) | Intake air temperature sensor |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Initial Engine Coolant Temp | Initial engine coolant temperature/ Min.: -40°C, Max.: 120°C | Engine coolant temperature when engine started | Sensor output when engine started | - |
| Diagnostic Note: For freeze frame data, this tells whether the malfunction happened at a cold start or with a warm engine. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Initial Intake Air Temp | Initial intake air temperature/ Min.: -40°C, Max.: 120°C | Intake air temperature when engine started | Sensor output when engine started | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Intake Air Temp (Turbo) | Intake air temperature after intercooler/ Min.: -40°C, Max.: 190°C | 70°C (158°F) or less | Sensor output (intake air temperature sensor after intercooler) | Decreased cooling efficiency of intercooler (contamination, clogging) |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Glow Control Unit Duty | Glow control unit duty/ Min.: 0%, Max.: 127.5% | - | Result of ECU calculations | - |
| Diagnostic Note: This is the ECM command. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Alternate Duty Ratio | Alternator generation duty ratio/ Min.: 0%, Max.: 100% |
| Duty value from ALT terminal |
|
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Starter Signal | Starter signal/ ON or OFF | ON: Cranking | - |
|
Symptoms when out of range:
| ||||
| Diagnostic Note: Ignition switch (STA) output:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| A/C Signal | A/C (Air Conditioner) signal/ ON or OFF | ON: A/C on | A/C operation signal output from A/C amplifier
|
|
| Symptoms when out of range: OFF malfunction (OFF even when A/C switch is turned on):
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Stop Light Switch | Stop light switch/ ON or OFF |
| Switch output (stop light switch) |
|
| Symptoms when out of range: Stop light switch malfunction DTC P0504 is stored | ||||
| Diagnostic Note: Stop light switch (STP) operation condition:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Immobiliser Communication | Immobiliser communication/ ON or OFF |
| - |
|
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Neutral Position SW Signal | Park/neutral position switch status/ ON or OFF | ON: Shift lever in neutral | Switch output (Park/neutral position switch) | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Battery Voltage | Battery voltage/ Min.: 0 V, Max.: 15 V | 11 to 14 V | - | - |
| Symptoms when out of range: If 5 V or less, starting becomes difficult | ||||
| Diagnostic Note: If 11 V or less, characteristics of some electrical components change. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Atmosphere Pressure | Atmospheric pressure value/ Min.: 50 kPa, Max.: 120 kPa | Actual atmospheric pressure | Sensor output (atmospheric pressure sensor (built into ECM)) | Atmospheric pressure sensor itself has failed (atmospheric pressure sensor is inside the ECM) |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| ACT VSV | A/C cut status for Active Test/ ON or OFF | - | - | - |
| Diagnostic Note: "Control the A/C Cut Signal" Active Test support data. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| TC and TE1 | TC and TE1 connection status for Active Test/ ON or OFF | - | - | - |
| Diagnostic Note: When the "Connect the TC and TE1" Active Test is performed, the system behaves as if TC and CG were connected. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| # Codes (Include History) | Number of codes/ Min.: 0, Max.: 255 | - | - | - |
| Diagnostic Note: Number of DTCs appearing at least once during the last 40 times the vehicle was warmed up. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Check Mode | Check mode/ ON or OFF | ON: Check mode on | - | - |
| Diagnostic Note: Check Mode: The mode in which certain DTCs can be detected more easily and with higher sensitivity. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| MIL | MIL status/ ON or OFF | OFF: MIL off | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Engine Run Time | Engine run time/ Min.: 0 sec., Max.: 65535 sec. | Time after the ignition switch turned to ON | Result of ECU calculations (using the engine speed) | - |
| Diagnostic Note: Time passed since the ignition switch was turned to ON. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Time after DTC Cleared | Time after DTC cleared/ Min.: 0 min., Max.: 65535 min. | Time after DTCs cleared | - | - |
| Diagnostic Note: Time elapsed since the DTCs were cleared (or shipment from the factory). | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Distance from DTC Cleared | Distance driven after DTC cleared/ Min.: 0 km, Max.: 65535 km | Distance driven after DTCs cleared | - | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Warmup Cycle Cleared DTC | Warmup cycles after DTC cleared/ Min.: 0, Max.: 255 | - | - | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| OBD Requirements | Identifying OBD requirement | - | - | - |
| Diagnostic Note: Not OBD compliant | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Number of Emission DTC | Number of emissions-related DTCs | - | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Complete Parts Monitor | Complete parts monitor/ Not Avl or Avail | - | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Engine Start Time | Engine start time/ Min.: 0 ms, Max.: 267000 ms | - | - | - |
| Diagnostic Note: Time necessary for the engine to start. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Fuel Remaining Volume | Amount of remaining fuel/ Min.: 0 %, Max.: 100 % | - | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Accel Position | Accelerator position status/ Min.: 0%, Max.: 100% |
|
| - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Accel Sens. No.1 Volt % | Accelerator position No. 1/ Min.: 0%, Max.: 100% |
| Sensor output (Accelerator pedal position sensor) | - |
| Diagnostic Note: Read value with ignition switch ON (do not start engine). | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Accel Sens. No.2 Volt % | Accelerator position No. 2/ Min.: 0%, Max.: 100% |
| Sensor output (Accelerator pedal position sensor) | - |
| Diagnostic Note: Read value with ignition switch ON (do not start engine). | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Swirl Control Valve VSV | Status of vacuum switching valve (for swirl control valve)/ ON or OFF | ON: Idling | - | - |
| Compression |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Engine Speed of Cyl #1 Engine Speed of Cyl #2 Engine Speed of Cyl #3 Engine Speed of Cyl #4 | Engine speed for No. 1 to No. 4 cylinder/ Min.: 0 rpm, Max.: 51199 rpm | Engine speeds of all cylinders almost same | - | Compression goes down |
| Symptoms when out of range: When the engine speeds of all cylinders are not equal, idling will be rough. | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Av Engine Speed of All Cyl | Engine speed for all cylinders/ Min.: 0 rpm, Max.: 51199 rpm | - | - | - |
Diagnostic Note:
| ||||
| Vehicle Information |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Model Code | Model code | - | - | - |
| Diagnostic Note: Identifying model code: KUN# | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Engine Type | Engine type | - | - | - |
| Diagnostic Note: Identifying engine type: 1KDFTV | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Cylinder Number | Cylinder number/ Min.: 0, Max.: 255 | - | - | - |
| Diagnostic Note: Identifying cylinder number: 4 | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Transmission Type | Transaxle type/ MT or ECT 5th | - | - | - |
| Diagnostic Note: Identifying transaxle type:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Destination | Destination | - | - | - |
| Diagnostic Note: Identifying destination: W | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Model Year | Model year/ Min.: 1900, Max.: 2155 | - | - | - |
| Diagnostic Note: Identifying model year: 20## | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| System Identification | System identification | - | - | - |
| Diagnostic Note: Used for identifying the engine system: Diesel (diesel engine) | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| VN Turbo Type | VN turbo type/ Not Avl, Commo, Vacuum, CAN com, DC | DC*
| - | - |
| Diagnostic Note: Indicates the VN turbo vane actuation method.
| ||||
| Diesel Injection |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Target Common Rail Pressure | Target common rail pressure/ Min.: 0 kPa, Max.: 250000 kPa | 30000 to 200000 kPa when engine running | Target common rail pressure (ECU calculated value) | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Fuel Press | Fuel pressure/ Min.: 0 kPa, Max.: 250000 kPa | Idling: 30000 to 50000 kPa | Sensor output (fuel pressure sensor) |
|
| Symptoms when out of range: Difficult to start, poor driveability, lack of power, abnormal combustion noise | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Common Rail Pres Sens 2 | Fuel pressure/ Min.: 0 kPa, Max.: 250000 kPa | Idling: 30000 to 50000 kPa | Sensor output (fuel pressure sensor) |
|
| Symptoms when out of range: Poor driveability, lack of power, abnormal combustion noise. | ||||
| Diagnostic Note: Common Rail Pres Sens 2 indicates the output value from the No. 4 injector assembly (fuel pressure sensor). | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Target Pump SCV Current | Final pump current target value/ Min.: 0 mA, Max.: 4000 mA | Idling: 923 to 1123 mA | Target value control (pump current) |
|
| Symptoms when out of range: Difficulty starting, lack of power or rough idling | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Pump SCV Learning Value | Pump SCV learning value/ Min.: -4096 mA, Max.: 4095.8 mA |
| Learned value |
|
| Symptoms when out of range: Difficulty starting, lack of power or rough idling | ||||
| Diagnostic Note: If the value is stuck at 200 mA or higher or -200 mA or less, it indicates that the operation is poor (poor movement due to deposits, etc.). | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Inj. FB Vol. for Idle | Idle stability status integral control volume/ Min.: -80 mm3/st, Max.: 79 mm3/st | -10 to 10 mm3/st | - | - |
| Symptoms when out of range: Engine friction problem, compression problem or injector breakdown | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Idle Signal Output Value | Idle signal output value/ Min.: 0, Max.: 255 |
| - | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Injection Volume | Injection volume/ Min.: 0 mm3/st, Max.: 1279.98 mm3/st | Idling: 2.0 to 11 mm3/st | Calculated value | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Fuel Return Temp | Fuel return temperature/ Min.: -40°C, Max.: 140°C | Idling after engine warmed-up: 35 to 85°C (95 to 185°F) | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Injection Pressure Correction | Injection pressure feedback compensation volume/ Min.: -500 mm3/st, Max.: 780 mm3/st | -400 to 400 mm3/st at standard temperature | Calculated value |
|
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Injection Feedback Val #1 Injection Feedback Val #2 Injection Feedback Val #3 Injection Feedback Val #4 | Injection volume correction for each cylinder/ Min.: -10 mm3/st, Max.: 10 mm3/st | Idling: -3.0 to 3.0 mm3/st | Learned value |
|
| Symptoms when out of range: Rough idling, black smoke, white smoke, poor driveability, lack of power, abnormal combustion noise, difficult to start | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Pilot 1 Injection Period | Pilot 1 injection period/ Min.: 0 μs, Max.: 65535 μs | Idling: 100 to 400 μs | Calculated value | - |
| Symptoms when out of range: Combustion noise, poor driveability, white smoke | ||||
| Diagnostic Note: Check to see if "Pilot 1 Injection Period" is not zero when symptoms occur. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Pilot 2 Injection Period | Pilot 2 injection period/ Min.: 0 μs, Max.: 65535 μs | Idling: 100 to 400 μs | Calculated value | - |
| Symptoms when out of range: Combustion noise, poor driveability, white smoke | ||||
| Diagnostic Note: Check to see if "Pilot 2 Injection Period" is not zero when symptoms occur. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Main Injection Period | Main injection period/ Min.: 0 μs, Max.: 65535 μs | Idling: 100 to 400 μs | Calculated value | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| After Injection Period | After injection period/ Min.: 0 μs, Max.: 65535 μs | - | Calculated value | - |
| Diagnostic Note: Check to see if "After Injection Period" is not zero when the following symptoms occur: Black smoke, poor driveability. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Pilot 1 Injection Timing | Pilot 1 injection timing/ Min.: -70°CA, Max.: 20°CA | Idling after engine warmed up and vehicle under normal atmospheric pressure:
| Calculated value | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Pilot 2 Injection Timing | Pilot 2 injection timing/ Min.: -50°CA, Max.: 20°CA | Idling after engine warmed up and vehicle under normal atmospheric pressure:
| Calculated value | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Main Injection Timing | Main injection timing/ Min.: -90°CA, Max.: 90°CA | Idling after engine warmed up and vehicle under normal atmospheric pressure:
| Calculated value | - |
| Diagnostic Note: Use "Main Injection Timing" to check poor drivability when the following symptoms are present: Bad injection timing, black smoke, and white smoke. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| After Injection Timing | After injection timing/ Min.: -10°CA, Max.: 50°CA | - | Calculated Value | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Pressure Discharge Valve | Pressure discharge valve operation/ ON or OFF | ON: Pressure discharge valve open | - | - |
| Diagnostic Note: This is the ECM command. | ||||
| EGR System |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Target EGR Position | EGR valve target opening amount/ Min.: 0%, Max.: 100% | Idling after engine warmed up: 0 to 90% | ECU-calculated value based on sensors (mass air flow meter, manifold absolute pressure sensor, intake air temperature (built into mass air flow meter), etc.) | - |
Symptoms when out of range:
| ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Actual EGR Valve Pos. | EGR valve position/ Min.: 0%, Max.: 100% | Idling after engine warmed up: 0 to 92% | Calculated from EGR valve position sensor | - |
Symptoms when out of range:
| ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| EGR Motor Duty #1 | EGR valve motor duty/ Min.: 0 %, Max.: 100% | Idling after engine warmed up: 1 to 25% | - | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| EGR Operation Prohibit | EGR operation prohibition/ OK or NG | OK: Possible to perform "Control the EGR Step Position" and "Activate the EGR Valve Close" Active Tests | - | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| EGR Close Lrn. Val. | EGR fully closed position learned value/ Min.: 0 V, Max.: 5 V | 0 to 1 V | EGR valve position sensor value when EGR valve fully closed | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| EGR Close Lrn. Status | EGR valve fully closed position learning status/ OK or NG | OK | - | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| EGR Cooler Bypass VSV | Status of vacuum switching valve (EGR bypass valve)/ ON or OFF |
| - |
|
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| EGR Cooler Bypass Position | Status of the EGR Cooler Bypass Position/ Cooler or Bypass |
| - |
|
Diagnostic Note:
| ||||
| Diesel Throttle System |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Throttle Sensor Volt % | Absolute throttle position sensor/ Min.: 0%, Max.: 100% |
| Sensor output (throttle position sensor) | - |
Symptoms when out of range:
| ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Target Throttle Position | Target throttle position/ Min.: -128%, Max.: 127% |
| Value calculated by ECM | - |
| Diagnostic Note: If there is a malfunction of the throttle actuator, compare the target and actual throttle position values for troubleshooting. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Actual Throttle Position | Actual diesel throttle position/ Min.: -20%, Max.: 120% | Idling after engine warmed-up: 0 to 92% | - | - |
Symptoms when out of range:
| ||||
| Diagnostic Note: Closing percentage of the throttle valve.
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Throttle Motor Duty | Diesel throttle motor duty/ Min.: 0%, Max.: 100% | - | - | - |
| Diagnostic Note: When the moving force to open and close the diesel throttle valve increases, the value of the Throttle Motor Duty increases. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Throttle Close Learning Val. | Throttle fully closed position learned value/ Min.: 0 deg, Max.: 84 deg | 14.25 to 21.25 deg | - | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Diesel Throttle Learn Status | Diesel throttle learning history/ OK or NG | OK | - | - |
Diagnostic Note:
| ||||
| VN Turbo System |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Target Booster Pressure | Target booster pressure/ Min.: 0 kPa, Max.: 320 kPa | Driving vehicle on level surface at 3000 rpm with full load: 200 to 225 kPa | Value calculated by ECM | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Boost Pressure Deviation | Boost pressure deviation/ Min.: -320 kPa, Max.: 320 kPa | - | - | - |
| Diagnostic Note: Difference between target and actual boost pressure. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| VN Turbo Command | VN turbo command value/ Min.: 0%, Max.: 100% | 0 to 98% | Controls the VN turbo vane opening position | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Actual VN Position | Actual VN turbo position/ Min.: 0%, Max.: 127.5% | 0 to 100% | - | - |
| Diagnostic Note: If the vanes do not move smoothly or become stuck, the difference between the actual value and the target value ("VN Turbo Command") becomes larger, and as a result, the motor duty also becomes larger. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| VN Position Sensor Out | VN position sensor output voltage/ Min.: 0 V, Max.: 5 V | Idling after engine warmed-up: 1 to 3 V | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| VN Motor Duty | VN turbo motor duty/ Min.: 0%, Max.: 127.5% | 2 to 88% | - | - |
| Diagnostic Note: If the vanes do not move smoothly, the duty will increase towards 100%. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| VN Close Learn Value | VN turbo fully closed position learned value/ Min.: 0 V, Max.: 5 V | 1.5 to 2 V | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| VN Close Learn Status | VN turbo fully closed position learning status/ OK or NG | OK | - | - |
| Diagnostic Note: If learning is not complete, the vehicle performance may decrease (power output is low). | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| VN Turbo Max Angle | VN turbo maximum opening amount/ Min.: 0%, Max.: 100% | - | - | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| VN Turbo Min Angle | VN turbo minimum opening amount/ Min.: 0%, Max.: 100% | - | - | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| VN Turbo Operation prohibit | VN turbo operation prohibition/ OK or NG | OK: The "Test the Turbo Charger Step Motor" and "Activate the VN Turbo Open" Active Tests can be performed. | - | - |
| Diagnostic Note: When NG is displayed, the ECM does not permit "Test the Turbo Charger Step Motor" and "Activate the VN Turbo Open" Active Tests to be performed. | ||||
| Diesel Starting |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Engine Speed (Starter Off) | Engine speed when starter off/ Min.: 0 rpm, Max.: 1594 rpm | - | - | - |
| Diagnostic Note: Engine speed immediately after starting the engine. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Starter Count | Starter on count/ Min.: 0, Max.: 255 | - | - | - |
| Diagnostic Note: Number of times the starter turned on from the time the ignition switch was turned to ON. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Run Dist of Previous Trip | Distance driven during previous trip/ Min.: 0 km, Max.: 261 km | - | - | - |
| Diagnostic Note: Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip. After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Glow Request Lighting Time | Glow request lighting time/ Min.: 0 ms, Max.: 33423 ms | - | - | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| IG-ON Time | IG-ON Time/ Min.: 0 ms, Max.: 33423 ms | - | - | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Immobiliser Fuel Cut History | Immobiliser fuel cut history/ ON or OFF | OFF | - | - |
| Diagnostic Note: If Immobiliser Fuel Cut History was "ON" when DTC P1604 (Startability Malfunction) was stored, the engine could not be started due to the immobiliser. | ||||
| Diesel Rough |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Rough Idle #1 Rough Idle #2 Rough Idle #3 Rough Idle #4 | Status of the rough idle #1 to #4/ ON or OFF | OFF | - | Injector assembly |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Electric Duty Feedback Value | Electric load feedback value/ Min.: 0 mm3/st, Max.: 39.8 mm3/st | 0 to 3.3 mm3/st | - | - |
| Diagnostic Note: Expected injection volume increase after the electrical load turns from off to on. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| A/C Duty Feedback Value | A/C load feedback value/ Min.: 0 mm3/st, Max.: 39.8 mm3/st | 0 to 3.4 mm3/st | - | - |
| Diagnostic Note: Expected injection volume increase after the A/C turns from off to on. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| PS Duty Feedback Value | Power steering load feedback value/ Min.: 0 mm3/st, Max.: 39.8 mm3/st | 0 mm3/st | - | - |
| Diagnostic Note: Expected injection volume increase after the power steering turns from off to on. | ||||
| Diesel Power |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| MAF Low | Mass air flow low/ ON or OFF | OFF | - |
|
| Symptoms when out of range: Lack of power | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Boost Pressure Low | Status of the Boost Pressure Low/ ON or OFF | OFF | - |
|
| Symptoms when out of range: Lack of power | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Common Rail Pressure Low | Status of the Common Rail Pressure Low/ ON or OFF | OFF | - |
|
| Symptoms when out of range: Lack of power | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Engine Coolant Temp High | Status of the Engine Coolant Temp High/ ON or OFF | OFF | - |
|
| Symptoms when out of range: Lack of power | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| MAF/Estimate MAF Ratio | Ratio of intake air amount to estimated intake air amount/ Min.: 0, Max.: 2.55 | Engine speed 4000 rpm, EGR system off: 0.6 to 1.4 | - |
|
| Symptoms when out of range: Lack of power | ||||
Diagnostic Note:
| ||||
| AT (for Automatic Transmission) |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Received MIL from ECT | MIL status from ECT/ ON or OFF | ON: MIL ON | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Shift Position Sig from ECT | Shift position signal from ECT/ 1st, 2nd, 3rd, 4th, 5th or 6th | - | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| A/T Oil Temp from ECT | ATF temperature from ECT/ Min.: -40°C, Max.: 215°C | With engine cold: Equal to ambient temperature | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| SPD (NO) | Output shaft speed/ Min.: 0 rpm, Max.: 12750 rpm | - | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| ECT Lock Up | Lock-up/ ON or OFF | ON: Lock-up operating | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| A/T Oil Temperature 1 | ATF temperature sensor value/ Min.: -40°C, Max.: 215°C | With engine cold: Equal to ambient temperature | - | - |
| Diagnostic Note: If the value is -40°C (-40°F) or 150°C (302°F), the ATF temperature sensor circuit is open or shorted. | ||||
| ACTIVE TEST |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test.
Perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the VSV for Swirl Control Valve | Activate the No. 1 vacuum switching valve (for swirl control valve) | ON/OFF | Confirm that the vehicle is stopped and the engine is idling |
| Control the A/C Cut Signal | Control the A/C signal | ON/OFF | Confirm that the vehicle is stopped and the engine is idling |
| Connect the TC and TE1 | Turn on the TC and TE1 connection | ON/OFF | - |
| Control the EGR Step Position | Control the electric EGR control valve assembly | 0 to 100% | Test is possible when the following conditions are met:
|
| Diesel Throttle Target Angle | Control the diesel throttle valve | 0 to 90% | Test is possible when the following conditions are met:
|
| Test the Turbo Charger Step Motor | Activate the turbocharger | 40 to 100% | Test is possible when the following conditions are met:
|
| Test the Fuel Leak | Pressurize the common rail and check for fuel leaks | Stop/Start |
|
| Activate the VN Turbo Open | Activate the turbocharger sub-assembly | ON/OFF | Confirm that the engine is running. |
| Activate the EGR Valve Close | Activate the electric EGR control valve assembly | ON/OFF | Confirm that the vehicle is stopped and the engine is idling |
| Activate the VSV for EGR Cooler Bypass | Activate the vacuum switching valve (EGR bypass valve) | Bypass/Half Pos/Cooler | Test is possible when the following conditions are met:
|
| Control the Select Cylinder Fuel Cut | Selected cylinder (cylinder #1 to #4) injector fuel cut | #1/#2/#3/#4 ON/OFF | Fuel injection is stopped while the test is ON.
|
| Check the Cylinder Compression* | Check the cylinder compression pressure | ON/OFF | Fuel injection stops in all cylinders. |
| SYSTEM CHECK |
Activate the Pressure Discharge Valve Check
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
![]() |
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Pressure Discharge Valve Check.
![]() |
Press "Next".
![]() |
Press "Next" again to proceed.
![]() |
Select the check type "Valve Check for Graph".

![]() |
Select the check type "Close to Open Check" or "Always Closed Check".

