Home › ENGINE ยท 2TR-FBE › EXHAUST › EXHAUST PIPE

EXHAUST PIPE > INSTALLATION

for Preparation Click here



1. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A107610
  1. Using a vernier caliper, measure the free length of the compression spring.

    Minimum length:
    40 mm (1.57 in.)

    If the length is less than the minimum, replace the compression spring.

  1. Install the front pipe to the pipe support.



    A099436E03
  1. Install a new gasket to the exhaust manifold.

    NOTICE:
    1. Make sure the gasket is facing the correct direction.
    2. Do not reuse the gasket.
    3. To ensure a proper seal, do not use the front pipe to force the gasket onto the exhaust manifold.

    HINT:
    Using a plastic-faced hammer, uniformly strike the gasket so that the gasket and exhaust manifold are properly fit.

  1. Install the front pipe with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



2. INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)


    A112121E01
  1. Using SST, install the heated oxygen sensor.

    SST
    09224-00010  

    Torque:
    for use without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    for use with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). When using a torque wrench with a fulcrum length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.

  1. Connect the heated oxygen sensor connector.



3. INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)


    G039121E01
  1. Using SST, install the air fuel ratio sensor.

    SST
    09224-00010  

    Torque:
    for use without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    for use with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). When using a torque wrench with a fulcrum length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.

  1. Attach the 3 wire harness clamps to the vehicle body.

  1. Connect the air fuel ratio sensor connector.



4. INSTALL CENTER EXHAUST PIPE ASSEMBLY
  1. Install the center pipe to the 3 pipe supports.

  1. Install a new gasket and the center pipe to the front pipe with the 2 bolts and 2 nuts. Alternately tighten the bolts in several passes.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    Do not reuse the gasket.



5. INSTALL TAILPIPE ASSEMBLY
  1. Install the tailpipe to the pipe support.

  1. Install a new gasket and the tailpipe to the center pipe with the 2 bolts and 2 nuts. Alternately tighten the bolts in several passes.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    Do not reuse the gasket.



6. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the problem areas to stop the leak. Replace damaged parts as necessary.