Home › ENGINE ยท 2TR-FE › EXHAUST › EXHAUST PIPE

EXHAUST PIPE > INSTALLATION

for Preparation Click here



1. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A107610
  1. Using a vernier caliper, measure the free length of the compression spring.

    Minimum length:
    40 mm (1.57 in.)

    If the length is less than the minimum, replace the compression spring.

  1. Install the front pipe to the pipe support.



    A099436E03
  1. Install a new gasket to the outlet pipe.

    HINT:
    Using a plastic-faced hammer, uniformly strike the gasket so that the gasket and exhaust pipe are properly fit.

    NOTICE:
    1. Be careful with the installation direction of the gasket.
    2. Do not reuse the gasket.
    3. To ensure a proper seal, do not use the front pipe to force the gasket onto the outlet pipe.

  1. Install the front pipe with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



2. INSTALL HEATED OXYGEN SENSOR (w/ Secondary Air Injection System)


    A112121E03
  1. Using SST, install the sensor.

    SST
    09224-00010  

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf } for use without SST
    40 N*m{ 408 kgf*cm , 30 ft.*lbf } for use with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).



    A112117E01
  1. Connect the sensor connector.



3. INSTALL HEATED OXYGEN SENSOR (w/o Secondary Air Injection System)


    A112982E01
  1. Using SST, install the sensor.

    SST
    09224-00010  

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf } for use without SST
    40 N*m{ 408 kgf*cm , 30 ft.*lbf } for use with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).



    G039109E02
  1. Attach the 3 wire clamps to the vehicle body.

  1. Connect the sensor connector.



4. INSTALL AIR FUEL RATIO SENSOR (w/ Secondary Air Injection System)


    A112982E01
  1. Using SST, install the sensor.

    SST
    09224-00010  

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf } for use without SST
    40 N*m{ 408 kgf*cm , 30 ft.*lbf } for use with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).



    G039109E02
  1. Attach the 3 wire clamps to the vehicle body.

  1. Connect the sensor connector.



5. INSTALL CENTER EXHAUST PIPE ASSEMBLY
  1. Install the center pipe to the 3 pipe supports.

  1. Install a new gasket and the center pipe to the front pipe with the 2 bolts and 2 nuts. Alternately tighten the bolts in several passes.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    Do not reuse the gasket.



6. INSTALL TAILPIPE ASSEMBLY
  1. Install the tailpipe to the pipe support.

  1. Install a new gasket and the tailpipe to the center pipe with the 2 bolts and 2 nuts. Alternately tighten the bolts in several passes.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    Do not reuse the gasket.



7. CHECK FOR EXHAUST GAS LEAKS
If gas is leaking, tighten the problem areas to stop the leak. Replace damaged parts as necessary.