AUTOMATIC TRANSMISSION UNIT > INSPECTION |
| 1. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY |
Remove the magnets and use them to collect steel particles.
Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.
| 2. INSPECT OVERDRIVE 1-WAY CLUTCH |
![]() |
Hold the overdrive direct clutch drum and turn the input shaft. Check that the input shaft can be turned clockwise freely and locks when turned counterclockwise.
![]() | Lock |
![]() | Free |
| 3. INSPECT OVERDRIVE DIRECT CLUTCH DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 4. INSPECT OVERDRIVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 5. INSPECT OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY |
![]() |
Check that the check ball is free by shaking the piston.
Check that the valve does not have leaks by applying low-pressure compressed air.
If the result is not as specified, replace the overdrive direct clutch piston sub-assembly.
| 6. INSPECT OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the clutch drum bushes.
| 7. INSPECT OVERDRIVE PLANETARY GEAR ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the planetary gear bush.
![]() |
Using a feeler gauge, measure the planetary pinion gear thrust clearance.
| 8. INSPECT OVERDRIVE BRAKE DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 9. INSPECT PISTON OPERATION OF OVERDRIVE BRAKE |
![]() |
Place the overdrive support assembly onto the direct clutch assembly.
![]() |
Apply compressed air (392 kPa (4 kgf/cm2, 57 psi)) into the oil passage and check that the overdrive brake piston moves smoothly.
| 10. INSPECT OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 11. INSPECT DIRECT CLUTCH DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 12. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 13. INSPECT DIRECT CLUTCH PISTON SUB-ASSEMBLY |
![]() |
Check that the check ball is free by shaking the piston.
Check that the valve does not have leaks by applying low-pressure compressed air.
| 14. INSPECT DIRECT CLUTCH DRUM SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the clutch drum bush.
| 15. INSPECT FORWARD CLUTCH DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 16. INSPECT FORWARD CLUTCH PISTON SUB-ASSEMBLY |
![]() |
Check that the check ball is free by shaking the piston.
Check that the valve does not have leaks by applying low-pressure compressed air.
| 17. INSPECT INPUT SHAFT SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the input shaft bush.
| 18. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 19. INSPECT SECOND COAST BRAKE PISTON ROD |
![]() |
Check the piston rod length.
| Groove Mark | Length |
| Without | 78.3 to 78.5 mm (3.083 to 3.090 in.) |
| With | 79.8 to 80.0 mm (3.142 to 3.149 in.) |
| 20. INSPECT SECOND COAST BRAKE BAND ASSEMBLY |
![]() |
| *1 | Printed Number |
| 21. INSPECT FRONT PLANETARY RING GEAR SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the planetary ring gear bush.
| 22. INSPECT FRONT PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the pinion gear thrust clearance.
| 23. INSPECT NO. 1 1-WAY CLUTCH ASSEMBLY |
![]() |
Hold the planetary sun gear and turn the 1-way clutch assembly. Check that the 1-way clutch hub can be turned clockwise freely and locks when turned counterclockwise.
![]() | Lock |
![]() | Free |
| 24. INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the planetary sun gear bushes.
| 25. INSPECT SECOND BRAKE PISTON |
![]() |
Check that the second brake piston moves smoothly when applying compressed air to and releasing low-pressure compressed air from the second brake drum.
| 26. INSPECT SECOND BRAKE DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 27. INSPECT SECOND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 28. INSPECT FIRST AND REVERSE BRAKE DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 29. INSPECT NO. 2 1-WAY CLUTCH |
![]() |
Hold the planetary gear and turn the 1-way clutch inner race. Check that the 1-way clutch inner race can be turned counterclockwise freely and locks when turned clockwise.
![]() | Lock |
![]() | Free |
| 30. INSPECT REAR PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the thrust clearance.
| 31. INSPECT FIRST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 32. INSPECT TRANSMISSION CASE BUSH |
![]() |
Using a cylinder gauge, measure the inside diameter of the transmission case rear bush.
| 33. INSPECT PISTON OPERATION OF FIRST AND REVERSE BRAKE |
![]() |
Make sure the first and reverse brake pistons move smoothly when compressed air is applied into the transmission case.
| 34. INSPECT PISTON OPERATION OF SECOND COAST BRAKE |
![]() |
Place a mark on the second coast brake piston rod.
| *1 | Mark |
| *2 | Piston Rod |
![]() |
Using SST, measure the stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).
| 35. INSPECT OUTPUT SHAFT END PLAY |
![]() |
Using a dial indicator, measure the end play of the output shaft while moving it by hand.
Check that the output shaft rotates smoothly.