AUTOMATIC TRANSMISSION UNIT > DISASSEMBLY |
| 1. REMOVE DRAIN PLUG |
Remove the drain plug and gasket.
| 2. REMOVE BREATHER HOSE |
![]() |
Remove the bolt and breather hose plug together with the breather hose and clamp.
Remove the breather hose from the breather hose plug.
| 3. REMOVE TRANSMISSION CONTROL SHAFT LEVER LH |
![]() |
Remove the nut, washer and control shaft lever.
| 4. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Using a screwdriver, bend the tabs of the lock washer.
| *1 | Lock Washer |
| *2 | Lock Nut |
Remove the lock nut and lock washer.
Remove the bolt and park/neutral position switch.
| 5. REMOVE ATF TEMPERATURE SENSOR |
![]() |
Remove the sensor.
| 6. REMOVE OIL COOLER TUBE UNION |
![]() |
Remove the 2 tube unions.
Remove the O-ring from each tube union.
| 7. REMOVE SPEED SENSOR NC0 |
![]() |
Remove the bolt and sensor.
Remove the O-ring from the sensor.
| 8. REMOVE SPEEDOMETER SENSOR |
![]() |
Remove the bolt and sensor.
Remove the O-ring from the sensor.
| 9. REMOVE SPEED SENSOR SP2 |
![]() |
Remove the bolt and sensor.
Remove the O-ring from the sensor.
| 10. REMOVE AUTOMATIC TRANSMISSION HOUSING |
![]() |
Remove the 6 bolts.
Remove the transmission housing.
| 11. SECURE TRANSMISSION CASE |
![]() |
Secure the transmission case to an overhaul attachment.
| 12. REMOVE EXTENSION HOUSING SUB-ASSEMBLY |
![]() |
Remove the 6 bolts.
Remove the extension housing and gasket.
| 13. REMOVE EXTENSION HOUSING BUSH APPLY TUBE |
![]() |
Remove the gasket from the extension housing bush apply tube.
| *1 | Extension Housing Bush Apply Tube |
| *2 | Extension Housing Bush Apply Tube Gasket |
Remove the extension housing bush apply tube.
| 14. REMOVE EXTENSION HOUSING DUST DEFLECTOR |
![]() |
Secure the extension housing in a vise between aluminum plates.
Using a screwdriver and hammer, tap off the dust deflector.
| 15. REMOVE AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL |
![]() |
Using a screwdriver, pry out the oil seal.
| *1 | Protective Tape |
| 16. REMOVE SPEEDOMETER DRIVE GEAR |
Using snap ring pliers, remove the snap ring.
![]() |
Remove the speedometer drive gear and the ball.
| *1 | Speedometer Drive Gear |
| *2 | Ball |
| 17. REMOVE SENSOR ROTOR |
![]() |
| *1 | Key |
| *2 | Snap Ring |
| *3 | Sensor Rotor |
Using a snap ring expander, remove the snap ring.
Remove the sensor rotor and key.
| 18. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 19 bolts.
![]() |
Insert the blade of an oil pan seal cutter between the transmission case and oil pan, and then cut through the applied sealer.
Remove the oil pan from the transmission case.
| 19. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY |
Remove the magnets and use them to collect steel particles.
Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.
| 20. REMOVE VALVE BODY OIL STRAINER ASSEMBLY |
Turn over the transmission.
![]() |
Remove the 4 bolts and valve body oil strainer from the valve body.
Remove the 3 gaskets from the oil strainer.
| 21. REMOVE TRANSMISSION WIRE |
![]() |
Disconnect the 4 connectors from the shift solenoid valves.
![]() |
Remove the bolt.
Pull out the transmission wire from the transmission case to remove it.
Remove the O-ring from the transmission wire connector.
| 22. REMOVE TRANSMISSION VALVE BODY ASSEMBLY |
![]() |
Remove the 20 bolts and valve body.
| 23. REMOVE CHECK BALL BODY |
![]() |
Remove the check ball body and spring.
| *1 | Check Ball Body |
| *2 | Spring |
| 24. REMOVE B-2 ACCUMULATOR PISTON |
![]() |
Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole to remove the B-2 accumulator piston and spring.
Remove the 2 O-rings from the piston.
| 25. REMOVE C-2 ACCUMULATOR PISTON |
![]() |
Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole to remove the C-2 accumulator piston and 2 springs.
Remove the 2 O-rings from the piston.
| 26. REMOVE B-0 ACCUMULATOR PISTON |
![]() |
Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole to remove the B-0 accumulator piston and spring.
Remove the 2 O-rings from the piston.
| 27. REMOVE C-0 ACCUMULATOR PISTON |
![]() |
Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole to remove the C-0 accumulator piston and 2 springs.
Remove the O-ring from the piston.
| 28. REMOVE PARKING LOCK PAWL BRACKET |
![]() |
Remove the 3 bolts and bracket.
| 29. REMOVE PARKING LOCK ROD SUB-ASSEMBLY |
![]() |
Disconnect the parking lock rod from the manual valve lever to remove it.
| 30. REMOVE PARKING LOCK PAWL |
![]() |
Pull out the parking lock pawl shaft from the front side, and then remove the lock pawl and spring.
| *1 | Parking Lock Pawl Shaft |
| *2 | Lock Pawl |
| *3 | Spring |
| *4 | E-Ring |
Remove the E-ring from the shaft.
| 31. REMOVE MANUAL VALVE LEVER SHAFT |
![]() |
Using a hammer and screwdriver, cut off the spacer and remove it from the shaft.
| *1 | Spacer |
| *2 | Protective Tape |
![]() |
Using a pin punch and hammer, tap out the spring pin.
Pull out the manual valve lever shaft through the case and remove the manual valve lever.
| 32. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL |
![]() |
Using a screwdriver, pry out the 2 oil seals.
| *1 | Protective Tape |
| 33. REMOVE OIL PUMP ASSEMBLY |
![]() |
Stand the transmission upright.
Remove the 7 bolts from the transmission case.
![]() |
Using SST, remove the oil pump assembly.
Remove the O-ring from the oil pump assembly.
![]() |
Remove the bearing race from the oil pump assembly.
| 34. REMOVE OVERDRIVE PLANETARY GEAR ASSEMBLY WITH OVERDRIVE DIRECT CLUTCH AND OVERDRIVE 1-WAY CLUTCH ASSEMBLY |
![]() |
Remove the planetary gear together with the direct clutch and 1-way clutch from the transmission case.
![]() |
Remove the bearing race and bearing.
| *1 | Bearing Race |
| *2 | Bearing |
| 35. INSPECT OVERDRIVE 1-WAY CLUTCH |
![]() |
Hold the overdrive direct clutch drum and turn the input shaft. Check that the input shaft can be turned clockwise freely and locks when turned counterclockwise.
![]() | Lock |
![]() | Free |
| 36. REMOVE OVERDRIVE DIRECT CLUTCH DRUM ASSEMBLY |
![]() |
| 37. REMOVE OVERDRIVE DIRECT CLUTCH DISC SET |
![]() |
Using a screwdriver, pry out the snap ring from the overdrive direct clutch drum.
| *1 | Protective Tape |
Remove the flange, 2 discs and 2 plates.
| 38. INSPECT OVERDRIVE DIRECT CLUTCH DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 39. REMOVE OVERDRIVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Place SST on the return spring and compress the return spring with a press.
Using SST, remove the snap ring.
Remove the clutch return spring.
| 40. INSPECT OVERDRIVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 41. REMOVE OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY |
![]() |
Place the oil pump onto the torque converter, and then place the overdrive direct clutch onto the oil pump.
Hold the overdrive direct clutch piston by hand and apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil pump to remove the overdrive direct clutch piston.
Remove the 2 O-rings from the piston.
| 42. INSPECT OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY |
![]() |
Check that the check ball is free by shaking the piston.
Check that the valve does not have leaks by applying low-pressure compressed air.
If the result is not as specified, replace the overdrive direct clutch piston sub-assembly.
| 43. INSPECT OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the clutch drum bushes.
| 44. REMOVE OVERDRIVE RETAINING PLATE |
![]() |
Using a screwdriver, pry out the snap ring.
| *1 | Protective Tape |
![]() |
Remove the retaining plate.
| 45. REMOVE OVERDRIVE 1-WAY CLUTCH OUTER RACE WITH OVERDRIVE 1-WAY CLUTCH |
![]() |
| 46. REMOVE OVERDRIVE 1-WAY CLUTCH |
![]() |
Remove the overdrive 1-way clutch from the outer race.
| 47. REMOVE NO. 3 OVERDRIVE PLANETARY GEAR THRUST WASHER |
![]() |
| 48. INSPECT OVERDRIVE PLANETARY GEAR ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the planetary gear bush.
![]() |
Using a feeler gauge, measure the planetary pinion gear thrust clearance.
| 49. REMOVE OVERDRIVE PLANETARY RING GEAR WITH OVERDRIVE PLANETARY RING GEAR FLANGE |
![]() |
Remove the ring gear together with the overdrive planetary ring gear flange from the transmission case.
![]() |
Remove the bearing and bearing race from the overdrive planetary ring gear.
| *1 | Bearing |
| *2 | Bearing Race |
| 50. REMOVE OVERDRIVE PLANETARY RING GEAR FLANGE |
![]() |
Using a screwdriver, pry out the snap ring.
| *1 | Protective Tape |
![]() |
Remove the ring gear flange from the overdrive planetary ring gear.
| 51. REMOVE OVERDRIVE BRAKE DISC SET |
![]() |
Using a screwdriver, pry out the snap ring.
| *1 | Protective Tape |
Remove the flange, 3 discs and 3 plates from the transmission case.
| 52. INSPECT OVERDRIVE BRAKE DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 53. INSPECT PISTON STROKE OF SECOND COAST BRAKE |
![]() |
Using a waterproof pen, place a mark on the second coast brake piston rod as shown in the illustration.
| *1 | Piston Rod |
| *2 | Mark |
![]() |
Using SST, measure the piston stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).
| 54. REMOVE OVERDRIVE SUPPORT SUB-ASSEMBLY |
![]() |
Remove the 2 bolts holding the overdrive support sub-assembly to the case.
![]() |
Using SST, remove the snap ring.
![]() |
Using SST, remove the overdrive brake assembly.
![]() |
Remove the bearing and bearing race from the overdrive brake.
| *1 | Bearing |
| *2 | Bearing Race |
| 55. INSPECT PISTON OPERATION OF OVERDRIVE BRAKE |
![]() |
Place the overdrive support assembly onto the direct clutch assembly.
![]() |
Apply compressed air (392 kPa (4 kgf/cm2, 57 psi)) into the oil passage and check that the overdrive brake piston moves smoothly.
| 56. REMOVE DIRECT CLUTCH ASSEMBLY WITH FORWARD CLUTCH ASSEMBLY |
![]() |
Remove the direct clutch together with the forward clutch from the case.
![]() |
Remove the 2 bearings and bearing race.
| *1 | Bearing |
| *2 | Bearing Race |
| 57. REMOVE FORWARD CLUTCH ASSEMBLY |
![]() |
Remove the forward clutch from the direct clutch.
![]() |
Remove the thrust washer from the forward clutch.
| *1 | Thrust Washer |
| 58. REMOVE OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Place SST on the return spring and compress the return spring with a press.
Using a screwdriver, pry out the snap ring.
| *1 | Protective Tape |
Remove the brake return spring.
| 59. INSPECT OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 60. REMOVE OVERDRIVE BRAKE PISTON |
![]() |
Place the overdrive support onto the direct clutch assembly.
Hold the overdrive brake piston so that it is not slanted and apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) into the passage to remove the overdrive brake piston.
![]() |
Remove the 2 O-rings from the overdrive brake piston.
| *1 | O-Ring |
| 61. REMOVE OVERDRIVE CLUTCH DRUM OIL SEAL RING |
![]() |
Remove the 2 oil seal rings from the overdrive support.
![]() |
Remove the clutch drum thrust washer from the overdrive support.
| 62. REMOVE SECOND COAST BRAKE PISTON |
![]() |
Using SST, remove the snap ring.
![]() |
Apply compressed air to the oil hole to remove the second coast brake cover, piston assembly and spring.
Remove the 2 O-rings from the cover.
| 63. REMOVE SECOND COAST BRAKE PISTON OIL SEAL RING |
![]() |
| 64. REMOVE SECOND COAST BRAKE PISTON ROD |
![]() |
Firmly press the piston down to compress the compression spring.
Remove the E-ring.
![]() |
Remove the piston rod, washer plate and spring from the piston.
| *1 | Piston Rod |
| *2 | Washer Plate |
| *3 | Spring |
| *4 | Piston |
| 65. REMOVE DIRECT CLUTCH DISC SET |
![]() |
Using a screwdriver, pry out the snap ring from the direct clutch drum.
| *1 | Protective Tape |
Remove the flange, 4 discs and 4 plates.
| 66. INSPECT DIRECT CLUTCH DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 67. REMOVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Place SST on the return spring and compress the return spring with a press.
Using SST, remove the snap ring.
Remove the return spring.
| 68. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 69. REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY |
![]() |
Place the direct clutch drum on the overdrive support.
Hold the direct clutch piston and apply compressed air (196 kPa (2.0 kgf/cm2, 28.5 psi)) to the overdrive support to remove the direct clutch piston.
![]() |
Using a small screwdriver, remove the 2 O-rings from the piston.
| *1 | O-Ring |
| *2 | Protective Tape |
| 70. INSPECT DIRECT CLUTCH PISTON SUB-ASSEMBLY |
![]() |
Check that the check ball is free by shaking the piston.
Check that the valve does not have leaks by applying low-pressure compressed air.
| 71. INSPECT DIRECT CLUTCH DRUM SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the clutch drum bush.
| 72. FIX FORWARD CLUTCH ASSEMBLY |
![]() |
Place the overdrive support on wooden blocks or equivalent to prevent the forward clutch shaft from touching the work stand.
Place the forward clutch on the overdrive support.
| 73. REMOVE FORWARD CLUTCH DISC SET |
![]() |
Using a screwdriver, pry out the snap ring from the input shaft.
| *1 | Protective Tape |
Remove the flange, 5 discs, 5 plates and cushion plate.
| 74. INSPECT FORWARD CLUTCH DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 75. REMOVE FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Place SST on the return spring and compress the return spring with a press.
Using SST, remove the snap ring.
![]() |
Remove the return spring.
| 76. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 77. REMOVE FORWARD CLUTCH PISTON SUB-ASSEMBLY |
![]() |
Place the input shaft onto the overdrive support.
Hold the forward clutch piston by hand and apply compressed air (196 kPa (2.0 kgf/cm2, 28.5 psi)) to the overdrive support to remove the forward clutch piston.
![]() |
Remove the O-ring from the input shaft.
| *1 | Protective Tape |
![]() |
Remove the 2 O-rings from the forward clutch piston.
| *1 | O-Ring |
| *2 | Protective Tape |
| 78. INSPECT FORWARD CLUTCH PISTON SUB-ASSEMBLY |
![]() |
Check that the check ball is free by shaking the piston.
Check that the valve does not have leaks by applying low-pressure compressed air.
| 79. REMOVE INPUT SHAFT OIL SEAL RING |
![]() |
Remove the 3 oil seal rings from the grooves of the input shaft.
| 80. INSPECT INPUT SHAFT SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the input shaft bush.
| 81. REMOVE SECOND COAST BRAKE BAND ASSEMBLY |
![]() |
Using a screwdriver, pry off the 2 E-rings from the pin and pull out the pin.
| *1 | Protective Tape |
![]() |
Remove the second coast brake band from the case.
| 82. INSPECT SECOND COAST BRAKE BAND ASSEMBLY |
![]() |
| *1 | Printed Number |
| 83. REMOVE FRONT PLANETARY RING GEAR SUB-ASSEMBLY |
![]() |
Remove the planetary ring gear from the case.
![]() |
Remove the bearing and bearing race from the planetary ring gear.
| *1 | Bearing |
| *2 | Bearing Race |
![]() |
Place the output shaft on wooden blocks or equivalent.
| *1 | Wooden Block |
| 84. INSPECT FRONT PLANETARY RING GEAR SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the planetary ring gear bush.
| 85. REMOVE FRONT PLANETARY GEAR ASSEMBLY |
![]() |
Remove the bearing race from the planetary gear.
![]() |
Using SST, remove the snap ring.
![]() |
Remove the planetary gear from the case.
![]() |
Remove the bearing and bearing race from the planetary gear.
| *1 | Protective Tape |
| 86. INSPECT FRONT PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the pinion gear thrust clearance.
| 87. REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY WITH SUN GEAR INPUT DRUM AND NO. 1 1-WAY CLUTCH ASSEMBLY |
![]() |
Remove the sun gear together with the sun gear input drum and 1-way clutch from the case.
| 88. INSPECT NO. 1 1-WAY CLUTCH ASSEMBLY |
![]() |
Hold the planetary sun gear and turn the 1-way clutch assembly. Check that the 1-way clutch hub can be turned clockwise freely and locks when turned counterclockwise.
![]() | Lock |
![]() | Free |
| 89. REMOVE NO. 1 1-WAY CLUTCH ASSEMBLY |
![]() |
| 90. REMOVE NO. 1 1-WAY CLUTCH THRUST WASHER |
![]() |
| 91. REMOVE SUN GEAR SHAFT OIL SEAL RING |
![]() |
Remove the 2 oil seal rings from the sun gear input drum.
| 92. REMOVE SUN GEAR INPUT DRUM |
![]() |
Place the planetary sun gear onto a wooden block or equivalent.
Using snap ring pliers, remove the snap ring.
Remove the input drum from the planetary sun gear.
| 93. REMOVE SUN GEAR INPUT DRUM SHAFT SNAP RING |
![]() |
Using a screwdriver, pry off the snap ring from the planetary sun gear.
| *1 | Protective Tape |
| 94. INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the planetary sun gear bushes.
| 95. REMOVE SECOND BRAKE DISC SET |
![]() |
Using a screwdriver, pry out the snap ring.
| *1 | Protective Tape |
Remove the flange, 5 discs and 5 plates.
| 96. REMOVE SECOND BRAKE PISTON SLEEVE |
![]() |
Using a screwdriver, remove the sleeve.
| *1 | Protective Tape |
| 97. REMOVE OUTPUT SHAFT WITH REAR PLANETARY GEAR, NO. 2 1-WAY CLUTCH, FIRST AND REVERSE BRAKE DISC SET AND SECOND BRAKE DRUM |
![]() |
Using SST and a screwdriver, remove the snap ring.
| *1 | Protective Tape |
![]() |
Remove the output shaft together with the rear planetary gear, No. 2 1-way clutch, first and reverse brake disc set and second brake drum from the transmission case.
![]() |
Remove the bearing from the transmission case.
| 98. REMOVE SECOND BRAKE DRUM SUB-ASSEMBLY |
![]() |
Remove the second brake drum.
| 99. REMOVE NO. 4 PLANETARY CARRIER THRUST WASHER |
![]() |
| 100. INSPECT SECOND BRAKE PISTON |
![]() |
Check that the second brake piston moves smoothly when applying compressed air to and releasing low-pressure compressed air from the second brake drum.
| 101. REMOVE SECOND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Place SST on the return spring and compress the piston return spring with a press.
Using SST, remove the snap ring.
Remove the second brake piston return spring seat.
![]() |
Remove the piston return spring.
| 102. INSPECT SECOND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 103. REMOVE SECOND BRAKE PISTON |
![]() |
Hold the second brake piston by hand and apply compressed air to the second brake drum to remove the second brake piston.
Remove the 2 O-rings from the piston.
| 104. REMOVE FIRST AND REVERSE BRAKE DISC SET |
Remove the 6 plates, 6 discs and flange.
| 105. INSPECT FIRST AND REVERSE BRAKE DISC |
![]() |
Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.
| 106. REMOVE OUTPUT SHAFT |
![]() |
| 107. REMOVE PLANETARY OUTPUT SHAFT OIL SEAL RING |
![]() |
| 108. REMOVE REAR PLANETARY RING GEAR |
![]() |
Remove the rear planetary gear from the planetary ring gear.
![]() |
Remove the bearing race and bearing from the planetary ring gear.
![]() |
Using a screwdriver, pry out the snap ring.
| *1 | Protective Tape |
![]() |
Remove the planetary ring gear flange.
| 109. INSPECT NO. 2 1-WAY CLUTCH |
![]() |
Hold the planetary gear and turn the 1-way clutch inner race. Check that the 1-way clutch inner race can be turned counterclockwise freely and locks when turned clockwise.
![]() | Lock |
![]() | Free |
| 110. REMOVE NO. 2 1-WAY CLUTCH |
![]() |
Remove the 1-way clutch inner race from the planetary gear.
![]() |
Using a screwdriver, pry out the snap ring.
| *1 | Protective Tape |
![]() |
Remove the 1-way clutch from the planetary gear.
![]() |
Remove the No. 2 planetary carrier thrust washer from the planetary gear.
![]() |
Remove the No. 1 planetary carrier thrust washer from the planetary gear.
| 111. INSPECT REAR PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the thrust clearance.
| 112. REMOVE LEAF SPRING |
![]() |
| 113. REMOVE BRAKE DRUM GASKET |
![]() |
| 114. REMOVE FIRST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Place SST on the first and reverse brake return spring and compress the brake return spring.
| *1 | Snap Ring |
Using SST, remove the snap ring and brake return spring.
| 115. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the spring together with the spring seat.
| 116. REMOVE NO. 2 FIRST AND REVERSE BRAKE PISTON |
![]() |
Hold the No. 2 first and reverse brake piston and apply compressed air to the transmission case to remove the brake piston.
Remove the O-ring from the brake piston.
| 117. REMOVE BRAKE REACTION SLEEVE |
![]() |
Using SST, remove the sleeve.
Remove the O-ring from the sleeve.
| 118. REMOVE NO. 1 1ST AND REVERSE BRAKE PISTON |
![]() |
Using SST, remove the brake piston.
Remove the 2 O-rings from the brake piston.
| 119. INSPECT TRANSMISSION CASE BUSH |
![]() |
Using a cylinder gauge, measure the inside diameter of the transmission case rear bush.