Home › TRANSMISSION ยท A343F AUTOMATIC TRANSMISSION › OIL PUMP

OIL PUMP > DISASSEMBLY

for Preparation Click here



1. REMOVE FRONT OIL PUMP BODY O-RING


D025646E01


2. FIX OIL PUMP ASSEMBLY


Q003426E03
  1. Place the oil pump body on the torque converter assembly.
    Text in Illustration 
    *1
    Torque converter assembly



3. REMOVE CLUTCH DRUM OIL SEAL RING


AT08412E01
  1. Remove the 2 clutch drum oil seal rings.



4. REMOVE STATOR SHAFT ASSEMBLY


AT08411E01
  1. Remove the 13 bolts and stator shaft assembly from the oil pump body.

  1. Remove the oil pump body from the torque converter assembly.



5. INSPECT FRONT OIL PUMP BODY


AT05153E01
  1. Using a dial indicator, measure the inside diameter of the oil pump body bush.

    Maximum inside diameter:
    38.138 mm (1.50 in.)

    If the inside diameter is more than the maximum, replace the oil pump body.



6. INSPECT STATOR SHAFT ASSEMBLY


AT05357E01
  1. Using a dial indicator, measure the inside diameter of the stator shaft bush.

    Maximum Inside Diameter:
    Front Side
    Rear Side
    21.527 mm (0.847 in.)
    27.026 mm (1.06 in.)

    If the inside diameter is more than the maximum, replace the stator shaft.



7. INSPECT CLEARANCE OF FRONT OIL PUMP BODY


AT00153E01
  1. Push the driven gear to one side of the body.

  1. Using a feeler gauge, measure the body clearance.

    Standard body clearance:
    0.07 to 0.15 mm (0.00276 to 0.00590 in.)

    If the body clearance is more than the maximum, replace the drive gear, driven gear or pump body assembly. Replace the part or parts determined to be the most likely cause of the problem.



    AT00154E01
  1. Using a feeler gauge, measure the tip clearance between the driven gear teeth and drive gear teeth.

    Standard tip clearance:
    0.004 to 0.248 mm (0.000157 to 0.00976 in.)

    If the tip clearance is more than the maximum, replace the drive gear, driven gear or pump body assembly. Replace the part or parts determined to be the most likely cause of the problem.



    AT00155E01
  1. Using a steel straightedge and feeler gauge, measure the side clearance of both gears.

    Standard side clearance:
    0.02 to 0.05 mm (0.000788 to 0.00196 in.)

    If the side clearance is more than the maximum, replace the drive gear, driven gear or pump body assembly. Replace the part or parts determined to be the most likely cause of the problem.

    HINT:
    There are 5 different thicknesses for drive and driven gears.

    Drive and Driven Gear Thickness:
    Mark
    Specified Condition
    M
    11.690 to 11.699 mm (0.4603 to 0.4605 in.)
    N
    11.700 to 11.709 mm (0.4606 to 0.4609 in.)
    P
    11.710 to 11.720 mm (0.4610 to 0.4614 in.)
    R
    11.721 to 11.730 mm (0.4615 to 0.4618 in.)
    S
    11.731 to 11.740 mm (0.4619 to 0.4622 in.)



8. REMOVE FRONT OIL PUMP DRIVE GEAR


D025799E01


9. REMOVE FRONT OIL PUMP DRIVEN GEAR


D025800E01


10. REMOVE FRONT OIL PUMP OIL SEAL


AT05152E01
  1. Using a screwdriver, pry out the front oil pump oil seal.

    NOTICE:
    Be careful not to damage the bush or oil pump body.