Home › ENGINE ยท 1KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/o EGR Cooler)

ECD SYSTEM (w/o EGR Cooler) > TERMINALS OF ECM

for Preparation Click here



A066714E75

HINT:
Each ECM terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Symbols (Terminal No.)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.


Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
BATT (E5-2) - E1 (E6-7)
L - BR
Battery (for measuring the battery voltage and for the ECM memory)
Always
11 to 14 V
IGSW (E4-9) - E1 (E6-7)
B-O - BR
Ignition switch
Ignition switch ON
11 to 14 V
+B (E4-1) - E1 (E6-7)
B - BR
Power source of ECM
Ignition switch ON
11 to 14 V
MREL (E4-8) - E1 (E6-7)
W-G - BR
MAIN relay
Ignition switch ON
11 to 14 V
10 seconds elapsed after ignition switch OFF
0 to 1.5 V
VC (E7-18) - E2 (E7-28)
R-W - BR
Power source of sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
VCS (E6-2) - E2S (E6-1)
L-W - P-L
Power source of fuel pressure sensor (sub)
Ignition switch ON
4.5 to 5.5 V
VPA (E4-22) - EPA (E4-28)
W-L - BR-W
Accelerator pedal position sensor (for engine control)
Ignition switch ON, accelerator pedal fully released
0.6 to 1.0 V
Ignition switch ON, accelerator pedal fully depressed
2.9 to 4.2 V
VPA2 (E4-23) - EPA2 (E4-29)
GR-G - BR-Y
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, accelerator pedal fully released
1.4 to 1.8 V
Ignition switch ON, accelerator pedal fully depressed
3.7 to 5.0 V
VCPA (E4-26) - EPA (E4-28)
LG-R - BR-W
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.0 V
VCP2 (E4-27) - EPA2 (E4-29)
BR-R - BR-Y
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.0 V
VG (E6-24) - EVG (E6-32)
W-R - B-W
MAF meter
Idling, A/C switch OFF
0.5 to 3.4 V
THA (E7-31) - E2 (E7-28)
Y-B - BR
IAT sensor (built into MAF meter)
Idling, intake air temperature at 20°C (68°F)
0.5 to 3.4 V
THIA (E7-20) - E2 (E7-28)
Y-G - BR
Intake air temperature sensor
Atmospheric air temperature
0.5 to 3.4 V
THW (E7-19) - E2 (E7-28)
R-L - BR
ECT sensor
Idling, engine coolant temperature at 80°C (176°F)
0.2 to 1.0 V
STA (E4-7) - E1 (E6-7)
B-Y*1 - BR
L-Y*2 - BR
Starter signal
Cranking
6.0 V or more
#1 (E7-24) - E1 (E6-7)
#2 (E7-23) - E1 (E6-7)
#3 (E7-22) - E1 (E6-7)
#4 (E7-21) - E1 (E6-7)
B-W - BR
R - BR
V - BR
Y-R - BR
Injector
Idling
Pulse generation
(see waveform 1)
NE+ (E7-27) - NE- (E7-34)
Y - L
Crankshaft position sensor
Idling
Pulse generation
(see waveform 2)
G+ (E6-23) - G- (E6-31)
Y - L
Camshaft position sensor
Idling
Pulse generation
(see waveform 2)
STP (E5-15) - E1 (E6-7)
G-W - BR
Stop light switch
Ignition switch ON, brake pedal depressed
7.5 to 14 V
Ignition switch ON, brake pedal released
0 to 1.5 V
ST1- (E5-14) - E1 (E6-7)
R-L - BR
Stop light switch
(opposite to STP)
Ignition switch ON, brake pedal depressed
0 to 1.5 V
Ignition switch ON, brake pedal released
7.5 to 14 V
TC (E4-11) - E1 (E6-7)
P-B - BR
Terminal TC of DLC3
Ignition switch ON
11 to 14 V
W (E4-12) - E1 (E6-7)
R-B - BR
MIL
MIL illuminated
0 to 3 V
MIL not illuminated
11 to 14 V
SPD (E5-17) - E1 (E6-7)
V-R - BR
Speed signal from combination meter
Ignition switch ON, slowly rotate wheel
Pulse generation
(see waveform 3)
PIM (E6-28) - E2 (E7-28)
L-B - BR
Manifold absolute pressure sensor
Apply negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg)
0.1 to 0.7 V
Same as atmospheric pressure
0.8 to 1.5 V
Apply positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg)
1.6 to 2.3 V
IREL (E4-10) - E1 (E6-7)
B-W - BR
EDU relay
Ignition switch ON
0 to 1.5 V
TACH (E4-4) - E1 (E6-7)
B-W - BR
Engine speed
Idling
Pulse generation
(see waveform 4)
PCR1 (E7-26) - E2 (E7-28)
R-Y - BR
fuel pressure sensor (main)
Idling
1.7 to 2.2 V
PCR2 (E7-33) - E2 (E7-28)
G-R - BR
fuel pressure sensor (sub)
Idling
1.2 to 1.6 V
GREL (E4-15) - E1 (E6-7)
R - BR
GLOW relay
Cranking
11 to 14 V
THF (E7-29) - E2 (E7-28)
G-B - BR
Fuel temperature sensor
Ignition switch ON
0.5 to 3.4 V
ALT (E7-8) - E1 (E6-7)
G - BR
Generator duty ratio
Idling
Pulse generation
(see waveform 5)
PCV+ (E7-2) - PCV- (E7-1)
G-W - G-Y
Suction control valve
Idling
Pulse generation
(see waveform 6)
INJF (E7-25) - E1 (E6-7)
P - BR
EDU
Idling
Pulse generation
(see waveform 7)
VNTO (E7-10) - E1 (E6-7)
B-O - BR
Turbo motor driver
Idling
Pulse generation
(see waveform 8)
VNTI (E7-17) - E1 (E6-7)
R-B - BR
Turbo motor driver
Idling
Pulse generation
(see waveform 9)
PRD (E7-32) - E1 (E6-7)
GR - BR
EDU
Ignition switch OFF
4 to 6.5 V
VLU (E6-29) - E2 (E7-28)
B - BR
Throttle position sensor
Ignition switch ON, throttle valve
fully opened
3.6 to 4.2 V
Ignition switch ON, throttle valve
fully closed
0.4 to 1.0 V
LUSL (E6-4) - E1 (E6-7)
GR - BR
Diesel throttle motor duty signal
Engine warmed up, racing engine
Pulse generation
(see waveform 10)
SCV (E7-15) - E01 (E7-7)
LG - W-B
VSV for No. 1 swirl control valve
Idling
0 to 1.5 V
Engine speed 2600 rpm or more
11 to 14 V
EGR (E6-9) - E1 (E6-7)
L-R - BR
E-VRV (for E-EGR)
Ignition switch ON
Pulse generation
(see waveform 11)
EGRC (E6-18) - E1 (E6-7)
Y-B - BR
VSV (for EGR Cut)
Ignition switch ON, EGR cuts (accelerator pedal fully depressed)
0 to 1.5 V
CAN+ (E5-22)*1 - E1 (E6-7)
V - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 12)
CAN- (E5-21)*1 - E1 (E6-7)
P - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 13)

HINT:
  1. *1: A/T
  2. *2: M/T


WAVEFORM 1
A009438E03
Injector No. 1 (to No. 4) injection signal 
ECM Terminal Name
(a) Between #1 and E1
(b) Between #3 and E1
(c) Between #4 and E1
(d) Between #2 and E1
Tester Range
5 V/DIV., 20 msec./DIV.
Condition
Idling with warm engine

HINT:
The waveform varies depending on the injector injection.


WAVEFORM 2
A098437E05
Crankshaft position sensor signal and Camshaft position sensor signal 
ECM Terminal Name
(a) Between NE+ and NE-
(b) Between G+ and G-
Tester Range
5 V/DIV., 20 msec./DIV.
Condition
Idling with warm engine

HINT:
The waveform varies depending on the engine speed.


WAVEFORM 3
G037487E04
Vehicle speed signal 
ECM Terminal Name
Between SPD and E1
Tester Range
5 V/DIV., 10 msec./DIV.
Condition
Driving at vehicle speed of 40 km/h (25 mph)

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 4
A093225E19
Engine speed signal 
ECM Terminal Names
Between TACH and E1
Tester Ranges
5 V/DIV., 10 msec./DIV.
Conditions
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 5
A155060E01
Generator duty ratio signal 
ECM Terminal Names
Between ALT and E1
Tester Ranges
5 V/DIV., 2 msec./DIV.
Conditions
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 6
A097624E03
Suction control valve signal 
ECM Terminal Name
Between PCV+ and PCV-
Tester Range
10 V/DIV., 5 msec./DIV.
Condition
Idling or cranking with warm engine

HINT:
The waveform varies depending on the suction control valve operation.


WAVEFORM 7
A009437E03
Injector injection confirmation signal 
ECM Terminal Name
Between INJF and E1
Tester Range
2 V/DIV., 20 msec./DIV.
Condition
Idling with warm engine

HINT:
The waveform varies depending on the injector injection.


WAVEFORM 8
A148022E01
Turbo motor driver input signal 
ECM Terminal Name
Between VNTO and E1
Tester Range
5 V/DIV., 20 msec./DIV.
Condition
Idling with warm engine

HINT:
The waveform varies depending on the turbocharger operation.


WAVEFORM 9
A148021E03
Turbo motor driver output signal 
ECM Terminal Name
Between VNTI and E1
Tester Range
5 V/DIV., 50 msec./DIV.
Condition
Idling with warm engine

HINT:
The waveform varies depending on the turbocharger status.


WAVEFORM 10
A091225E03
Diesel throttle motor signal 
ECM Terminal Name
Between LUSL and E1
Tester Range
1 V/DIV., 2 msec./DIV.
Condition
Warm engine with racing engine

HINT:
The waveform varies depending on the throttle valve operation.


WAVEFORM 11
A096634E03
E-VRV (for E-EGR) signal 
ECM Terminal Name
Between EGR and E1
Tester Range
5 V/DIV., 1 msec./DIV.
Condition
Idling with warm engine

HINT:
The waveform varies depending on the E-VRV (for E-EGR) operation.


WAVEFORM 12
G036660E03
CAN communication signal 
ECM Terminal Name
Between CAN+ and E1
Tester Range
1 V/DIV., 10 msec./DIV.
Condition
Engine is stopped, ignition switch ON

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 13
G036661E03
CAN communication signal 
ECM Terminal Name
Between CAN- and E1
Tester Range
1 V/DIV., 10 msec./DIV.
Condition
Engine is stopped, ignition switch ON

HINT:
The waveform varies depending on the CAN communication signal.