Terminal No. (Symbol)
| Wiring Color
| Terminal Description
| Condition
| Specified Condition
|
E32-23 (BATT) - E28-6 (E1)
| L - BR
| Battery (for measuring the battery voltage and for the ECM memory)
| Always
| 11 to 14 V
|
E31-24 (IGSW) - E28-6 (E1)
| B-O - BR
| Ignition switch
| Ignition switch ON
| 11 to 14 V
|
E32-24 (+B) - E28-6 (E1)
| B - BR
| Power source of ECM
| Ignition switch ON
| 11 to 14 V
|
E32-17 (+B2) - E28-6 (E1)
| B-R - BR
| Power source of ECM
| Ignition switch ON
| 11 to 14 V
|
E31-11 (MREL) - E28-6 (E1)
| W-G - BR
| MAIN relay
| Ignition switch ON
| 11 to 14 V
|
E31-11 (MREL) - E28-6 (E1)
| W-G - BR
| MAIN relay
| 30 seconds elapsed after ignition switch off
| 0 to 1.5 V
|
E31-6 (VCPA) - E31-5 (EPA)
| LG-R - BR-W
| Power source of accelerator pedal position sensor (for VPA)
| Ignition switch ON
| 4.5 to 5.5 V
|
E31-4 (VCP2) - E31-3 (EPA2)
| BR-R - BR-Y
| Power source of accelerator pedal position sensor (for VPA2)
| Ignition switch ON
| 4.5 to 5.5 V
|
E32-2 (VPA) - E31-5 (EPA)
| W-L - BR-W
| Accelerator pedal position sensor (for engine control)
| Ignition switch ON, accelerator pedal fully released
| 0.5 to 1.1 V
|
E32-2 (VPA) - E31-5 (EPA)
| W-L - BR-W
| Accelerator pedal position sensor (for engine control)
| Ignition switch ON, accelerator pedal fully depressed
| 3.0 to 4.6 V
|
E32-1 (VPA2) - E31-3 (EPA2)
| GR-G - BR-Y
| Accelerator pedal position sensor (for sensor malfunction detection)
| Ignition switch ON, accelerator pedal fully released
| 0.9 to 2.3 V
|
E32-1 (VPA2) - E31-3 (EPA2)
| GR-G - BR-Y
| Accelerator pedal position sensor (for sensor malfunction detection)
| Ignition switch ON, accelerator pedal fully depressed
| 3.4 to 5.0 V
|
E30-13 (VG) - E30-14 (EVG)
| W-R - B-W
| Mass air flow meter
| Idling
| Pulse generation
|
E30-7 (THA) - E30-1 (ETHA)
| Y-B - BR
| Intake air temperature sensor (built into mass air flow meter)
| Idling, intake air temperature at 20°C (68°F)
| 0.5 to 3.4 V
|
E30-10 (THIA) - E30-4 (ETHI)
| Y-G - BR
| Intake air temperature sensor
| Idling, intake air temperature at 0 to 80°C (32 to 176°F)
| 0.5 to 3.4 V
|
E30-9 (THW) - E30-3 (ETHW)
| R-L - BR
| Engine coolant temperature sensor
| Idling, engine coolant temperature at 80°C (176°F)
| 0.2 to 1.0 V
|
E32-6 (STA) - E28-6 (E1)
| B-Y - BR
| Starter signal
| Cranking
| 6.0 V or higher
|
E29-21 (#1) - E28-6 (E1)
| B-W - BR
| No. 1 injector assembly
| Idling
| Pulse generation (See waveform 2)
|
E29-22 (#2) - E28-6 (E1)
| R - BR
| No. 2 injector assembly
| Idling
| Pulse generation (See waveform 2)
|
E29-23 (#3) - E28-6 (E1)
| V - BR
| No. 3 injector assembly
| Idling
| Pulse generation (See waveform 2)
|
E29-24 (#4) - E28-6 (E1)
| Y-R - BR
| No. 4 injector assembly
| Idling
| Pulse generation (See waveform 2)
|
E27-13 (G+) - E27-14 (G-)
| Y - L
| Camshaft position sensor
| Idling
| Pulse generation (See waveform 5)
|
E27-7 (NE+) - E27-8 (NE-)
| Y - L
| Crankshaft position sensor
| Idling
| Pulse generation (See waveform 5)
|
E32-8 (STP) - E28-6 (E1)
| G-W - BR
| Stop light switch assembly
| Ignition switch ON, brake pedal depressed
| 7.5 to 14 V
|
E32-8 (STP) - E28-6 (E1)
| G-W - BR
| Stop light switch assembly
| Ignition switch ON, brake pedal released
| 0 to 1.5 V
|
E32-9 (ST1-) - E28-6 (E1)
| R-L - BR
| Stop light switch assembly (opposite to STP)
| Ignition switch ON, brake pedal depressed
| 0 to 1.5 V
|
E32-9 (ST1-) - E28-6 (E1)
| R-L - BR
| Stop light switch assembly (opposite to STP)
| Ignition switch ON, brake pedal released
| 7.5 to 14 V
|
E31-23 (TC) - E28-6 (E1)
| P-B - BR
| Terminal TC of DLC3
| Ignition switch ON
| 11 to 14 V
|
E32-19 (W) - E28-6 (E1)
| R-B - BR
| MIL
| MIL illuminated
| 0 to 3 V
|
E32-19 (W) - E28-6 (E1)
| R-B - BR
| MIL
| MIL not illuminated
| 11 to 14 V
|
E31-30 (SPD) - E28-6 (E1)
| V-R - BR
| Speed signal from combination meter assembly
| Ignition switch ON, slowly wheel rotated
| Pulse generation (See waveform 9)
|
E30-18 (VCPM) - E30-6 (EPIM)
| R-W - BR
| Power source of manifold absolute pressure sensor
| Ignition switch ON
| 4.5 to 5.5 V
|
E30-12 (PIM) - E30-6 (EPIM)
| L-B - BR
| Manifold absolute pressure sensor
| Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied
| 0.1 to 0.7 V
|
E30-12 (PIM) - E30-6 (EPIM)
| L-B - BR
| Manifold absolute pressure sensor
| Same as atmospheric pressure
| 0.8 to 1.5 V
|
E30-12 (PIM) - E30-6 (EPIM)
| L-B - BR
| Manifold absolute pressure sensor
| Positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) applied
| 1.6 to 2.3 V
|
E31-12 (IREL) - E28-6 (E1)
| B-W - BR
| EDU relay
| Idling
| 1 to 1.5 V
|
E32-18 (TACH) - E28-6 (E1)
| B-W - BR
| Engine speed
| Idling
| Pulse generation
|
E30-23 (ALT) - E28-6 (E1)
| G - BR
| Generator assembly (Alternator) duty ratio
| Idling
| Pulse generation
|
E27-23 (PCV+) - E27-12 (PCV-)
| G-W - G-Y
| Suction control valve
| Idling
| Pulse generation (See waveform 1)
|
E29-20 (INJF) - E28-6 (E1)
| P - BR
| Injector driver
| Idling
| Pulse generation (See waveform 3)
|
E29-19 (PRD) - E28-6 (E1)
| GR - BR
| Pressure discharge valve drive signal
| Engine warmed up, engine racing
| Pulse generation (See waveform 4)
|
E30-24 (RLFF) - E28-6 (E1)
| GR - BR
| Pressure discharge valve confirmation signal
| Engine warmed up, engine racing
| Pulse generation (See waveform 4)
|
E27-19 (IDLO) - E28-6 (E1)
| G - BR
| Injector Driver
| Idling
| 4 to 5.5 V
|
E29-18 (VIJ1) - E29-6 (EIJ1)
| B - R
| Power source of fuel pressure sensor (No. 1 injector assembly)
| Ignition switch ON
| 4.5 to 5.5 V
|
E29-12 (PIJ1) - E29-6 (EIJ1)
| W - R
| Fuel pressure sensor (No. 1 injector assembly)
| Engine warmed up, engine idling
| 1.4 to 1.7 V
|
E29-17 (VIJ2) - E29-5 (EIJ2)
| Y - L
| Power source of fuel pressure sensor (No. 2 injector assembly)
| Ignition switch ON
| 4.5 to 5.5 V
|
E29-11 (PIJ2) - E29-5 (EIJ2)
| G - L
| Fuel pressure sensor (No. 2 injector assembly)
| Engine warmed up, engine idling
| 1.4 to 1.7 V
|
E29-16 (VIJ3) - E29-4 (EIJ3)
| B - W
| Power source of fuel pressure sensor (No. 3 injector assembly)
| Ignition switch ON
| 4.5 to 5.5 V
|
E29-10 (PIJ3) - E29-4 (EIJ3)
| R - W
| Fuel pressure sensor (No. 3 injector assembly)
| Engine warmed up, engine idling
| 1.4 to 1.7 V
|
E29-15 (VIJ4) - E29-3 (EIJ4)
| L - Y
| Power source of fuel pressure sensor (No. 4 injector assembly)
| Ignition switch ON
| 4.5 to 5.5 V
|
E29-9 (PIJ4) - E29-3 (EIJ4)
| G - Y
| Fuel pressure sensor (No. 4 injector assembly)
| Engine warmed up, engine idling
| 1.4 to 1.7 V
|
E28-15 (M+) - E28-6 (E1)
| W - BR
| DC motor (turbocharger sub-assembly)
| Idling
| Pulse generation (See waveform 6)
|
E28-14 (M-) - E28-6 (E1)
| B - BR
| DC motor (turbocharger sub-assembly)
| Idling
| Pulse generation (See waveform 7)
|
E30-17 (VNVC) - E30-5 (VNE2)
| W - L
| Power source of nozzle vane position sensor
| Ignition switch ON
| 4.5 to 5.5 V
|
E30-11 (VNA) - E30-5 (VNE2)
| R - L
| Nozzle vane position sensor
| Ignition switch ON
| 2.3 to 2.7 V
|
E29-14 (VCVL) - E29-2 (EVLU)
| R-W - BR
| Power source of throttle position sensor
| Ignition switch ON
| 4.5 to 5.5 V
|
E29-8 (VLU) - E29-2 (EVLU)
| B- BR
| Throttle position sensor
| Ignition switch ON, throttle valve fully opened
| 3.6 to 4.2 V
|
E29-8 (VLU) - E29-2 (EVLU)
| B- BR
| Throttle position sensor
| Ignition switch ON, throttle valve fully closed
| 0.4 to 1.0 V
|
E27-17 (LUSL) - E28-6 (E1)
| GR - BR
| Diesel throttle duty signal
| Engine warmed up, racing engine
| Pulse generation (See waveform 8)
|
E29-13 (VCEG) - E29-1 (EEGL)
| R-W - BR
| Power source of EGR valve position sensor
| Ignition switch ON
| 4.5 to 5.5 V
|
E29-7 (EGRA) - E29-1 (EEGL)
| R-Y - BR
| EGR valve position sensor
| Ignition switch ON
| 0.6 to 1.4 V
|
E28-1 (EGM+) - E28-13 (ME01)
| L - W-B
| EGR valve duty signal
| Engine warmed up, idling
| Pulse generation
|
E28-2 (EGM-) - E28-13 (ME01)
| Y - W-B
| EGR valve duty signal
| Engine warmed up, idling
| Pulse generation
|
E28-9 (ECBV) - E28-6 (E1)
| B-L - BR
| Vacuum switching valve (for EGR bypass valve)
| Vacuum switching valve assembly (for EGR bypass valve) on
| 0 to 1.5 V
|
Vacuum switching valve assembly (for EGR bypass valve) off
| 11 to 14 V
|
E28-7 (SCV) - E28-11 (E01)
| LG - W-B
| Vacuum switching valve (for No. 1 swirl control valve)
| Idling
| 0 to 1.5 V
|
Engine speed 2600 rpm or more
| 11 to 14 V
|
E28-8 (SCV2) - E28-11 (E01)
| W-L - W-B
| Vacuum switching valve (for No. 2 swirl control valve)
| Idling
| 0 to 1.5 V
|
Engine speed 2600 rpm or more
| 11 to 14 V
|
E31-10 (AC1) - E28-11 (E01)
| Y - W-B
| A/C signal
| A/C switch on
| 0 to 1.5 V
|
A/C switch off
| 11 to 14 V
|
E31-13 (ACT) - E28-11 (E01)
| R-L - W-B
| A/C signal
| Ignition switch ON
| 11 to 14 V
|
A/C cut control on
| 0 to 3 V
|
E27-26 (NSW) - E28-11 (E01)
| L-Y - W-B
| Park/neutral position switch assembly
| Ignition switch ON, shift lever in P or N
| Below 3 V
|
Ignition switch ON, shift lever not in P or N
| 11 to 14 V
|
E27-16 (D) - E28-11 (E01)
| G-Y - W-B
| Park/neutral position switch assembly
| Ignition switch ON, shift lever in D
| 11 to 14 V
|
Ignition switch ON, shift lever not in D
| Below 1 V
|
E31-36 (CANL) - E28-6 (E1)
| W - BR
| CAN communication line
| Ignition switch ON
| Pulse generation (See waveform 10)
|
E31-35 (CANH) - E28-6 (E1)
| B - BR
| CAN communication line
| Ignition switch ON
| Pulse generation (See waveform 11)
|
E27-18 (CAN-) - E28-6 (E1)
| P - BR
| CAN communication line
| Ignition switch ON
| Pulse generation (See waveform 10)
|
E27-24 (CAN+) - E28-6 (E1)
| V - BR
| CAN communication line
| Ignition switch ON
| Pulse generation (See waveform 11)
|
E30-22 (CINJ) - E28-6 (E1)
| B - BR
| INJ communication line
| Engine warmed up, idling
| Pulse generation (See waveform 12)
|