DTC P1613 Secondary Air Injection Driver Malfunction |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P1613 | Either condition (1) or (2) met: (1) All conditions are met (1 trip detection logic):
|
|
| P1613 |
|
|
| P1613 |
|
|
![]() |
| *a | Component with harness connected (ECM) |
![]() |
| Item | Content |
| ECM Terminal Name | AIDI - E1 |
| Tester Range | 5 V/DIV., 20 ms/DIV. |
| Condition | Idling |
| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1613) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P1613 | A |
| P1613 and other DTCs | B |
|
| ||||
| OK | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (AIDI VOLTAGE) |
![]() |
| *a | Component with harness connected (ECM) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: CLOSE.
Start the engine.
Perform the AIR system forced operation while the engine is idling.
Measure the voltage between the AIDI and E1 terminals of the ECM connector when the AIR system is on and off.
Turn the ignition switch off.
| Results | Suspected Trouble Areas | Proceed To |
| Fixed at low voltage (1.6 V or less) even when AIR system ON (Air pump ON, ASV OPEN) |
| A |
| Fixed at high voltage (12 V or higher) even when AIR system OFF (Air pump OFF, ASV CLOSE) |
| B |
| Other than above: Fluctuating (duty signal other than 20, 40 or 80%) |
| C |
|
| ||||
|
| ||||
| A | |
| 3.INSPECT ECM (AIRP AND AIRV VOLTAGE) |
![]() |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E24-19 (AIRP) - E23-5 (E1) | Ignition switch ON | 11 to 14 V |
| E24-6 (AIRV) - E23-5 (E1) | Ignition switch ON | 11 to 14 V |
| *a | Component with harness connected (ECM) |
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER) |
Disconnect the ECM connector.
Disconnect the air injection control driver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A7-1 (E) - Body ground | Always | Below 1 Ω |
| A7-4 (SIP) - E24-19 (AIRP) | Always | Below 1 Ω |
| A7-3 (SIV) - E24-6 (AIRV) | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A7-2 (DI) - A7-1 (E) | Ignition switch ON | 11 to 14 V |
| Result | Proceed to |
| NG | A |
| OK | B |
Reconnect the ECM connector.
Reconnect the air injection control driver connector.
|
| ||||
| A | ||
| ||
| 5.CHECK AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT |
![]() |
Disconnect the air injection control driver connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A7-5 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E24-19 (AIRP) or A7-4 (SIP) - Body ground | Always | 10 kΩ or higher |
| E24-6 (AIRV) or A7-3 (SIV) - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector (to Air Injection Control Driver) |
Reconnect the air injection control driver connector.
|
| ||||
| OK | |
| 6.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE) |
![]() |
Disconnect the air injection control driver connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A7-2 (DI) - A7-1 (E) | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Air Injection Control Driver) |
Reconnect the air injection control driver connector.
|
| ||||
|
| ||||
| 7.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER) |
Disconnect the ECM connector.
Disconnect the air injection control driver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A7-2 (DI) - E25-30 (AIDI) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A7-2 (DI) or E25-30 (AIDI) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM and air injection control driver connectors.
|
| ||||
| OK | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - BODY GROUND) |
Disconnect the air injection control driver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A7-1 (E) - Body ground | Always | Below 1 Ω |
Reconnect the air injection control driver connector.
|
| ||||
| OK | |
| 9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Disconnect the air injection control driver connector.
![]() |
Connect terminals DI and SIV of the wire harness connector for the air injection control driver.
| *1 | Air Injection Control Driver |
| *2 | ECM |
| *a | Front view of wire harness connector (to Air Injection Control Driver) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.
Start the engine.
Perform the AIR system intrusive operation while the engine is idling.
Measure the voltage between the SIV and E terminals of the ECM connector when the AIR system is on and off.
Turn the ignition switch off.
| Tester Connection | Condition | Specified Condition |
| A7-3 (SIV) - A7-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| A7-3 (SIV) - A7-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
![]() |
Connect terminals DI and SIP of the wire harness connector for the air injection control driver.
| *1 | Air Injection Control Driver |
| *2 | ECM |
| *a | Front view of wire harness connector (to Air Injection Control Driver) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.
Start the engine.
Perform the AIR system intrusive operation while the engine is idling.
Measure the voltage between the SIP and E terminals of the ECM connector when the AIR system is on and off.
Turn the ignition switch off.
| Tester Connection | Condition | Specified Condition |
| A7-4 (SIP) - A7-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| A7-4 (SIP) - A7-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
Reconnect the air injection control driver connector.
|
| ||||
| OK | |
| 10.REPLACE AIR INJECTION CONTROL DRIVER |
Replace the air injection control driver.
| NEXT | |
| 11.CHECK WHETHER DTC OUTPUT RECURS (SYSTEM CHECK AUTOMATIC MODE) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear DTCs (if stored) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the intelligent tester initialization is finished.
Perform the system check operation by pressing Next.
After operating the AIR system, press the Exit button to confirm the AIR system pending codes.
Check Pending DTCs.
Turn the ignition switch off.
|
| ||||
| OK | ||
| ||