Home › BODY › WINDSHIELD / WINDOWGLASS › WINDSHIELD GLASS

WINDSHIELD GLASS > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE INNER REAR VIEW MIRROR ASSEMBLY
  1. Remove the inner rear view mirror assembly (Click here).



4. REMOVE FRONT DOOR OPENING TRIM LH
  1. Partially remove the front door opening trim weatherstrip LH so that the front pillar garnish LH can be removed .



5. REMOVE FRONT DOOR OPENING TRIM RH

HINT:
Use the same procedures described for the LH side.



6. REMOVE ASSIST GRIP SUB-ASSEMBLY FRONT


B206335

HINT:
Use the same procedure for both front assist grips.

  1. Remove the 2 screws and front assist grip.



7. REMOVE FRONT PILLAR GARNISH LH


B276932
  1. Detach the 2 clips and 2 guides and remove the front pillar garnish.



    B289825E01
  1. w/ Curtain Shield Airbag:
    Protect the curtain shield airbag assembly.

    1. Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

      Text in Illustration 
      *1
      Protective Cover
      *2
      Adhesive Tape



8. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.



9. REMOVE MAP LIGHT ASSEMBLY


    E289365
  1. Remove the 2 screws.

  1. Detach the claw and 2 guides and remove the map light assembly.

  1. Disconnect the connector.



10. REMOVE ROOM NO. 1 LIGHT ASSEMBLY


    E225173
  1. Using a screwdriver wrapped with protective tape, detach the 4 claws and remove the lens.

    HINT:
    Protective tape the screwdriver tip before use.



    B117645
  1. Remove the 2 screws and room light.

  1. Disconnect the light connector.



11. REMOVE VISOR ASSEMBLY LH


B266814
  1. Detach the guide.

  1. Remove the 2 screws and visor.



12. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



13. REMOVE VISOR HOLDER LH


B266815
  1. Remove the screw.

  1. Detach the 2 claws and remove the visor holder.



14. REMOVE VISOR HOLDER RH

HINT:
Use the same procedure described for the LH side.



15. REMOVE ASSIST GRIP


B277629E01

HINT:
Use the same procedure for all assist grips.

  1. Using a screwdriver, detach the 4 claws and open the 2 covers.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape



    B206336
  1. Remove the 2 screws and assist grip.



16. REMOVE ROOF HEADLINING ASSEMBLY

HINT:
It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining.

  1. Partially remove the roof headlining .



17. REMOVE FRONT WIPER ARM HEAD CAP


    E225950
  1. Open the wiper arm head cap.



    E225948
  1. Remove the nut and arm and blade.



18. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E225271
  1. Remove the nut and the front wiper arm and blade assembly LH.



19. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E225272
  1. Remove the nut and the front wiper arm and blade assembly RH.



20. REMOVE HOOD TO COWL TOP SEAL


    E225273
  1. Using a clip remover, detach the 9 clips and remove the hood to cowl top seal.



21. REMOVE COWL TOP VENTILATOR LOUVER LH


    E225275
  1. Remove the clip.

  1. Detach the 5 claws and 5 guides, and remove the cowl top ventilator louver RH in the direction indicated by the arrow in the illustration.



22. REMOVE COWL TOP VENTILATOR LOUVER RH


    E225274
  1. Remove the clip.

  1. Detach the 5 guides, and remove the cowl top ventilator louver LH in the direction indicated by the arrow in the illustration.



23. REMOVE WINDSHIELD MOULDING OUTER UPPER


B050448E03
  1. Using a knife, cut off the moulding as shown in the illustration.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Remove the remaining moulding.

    HINT:
    Make a partial cut in the moulding. Then pull and remove it by hand.



24. REMOVE WINDSHIELD GLASS


B084567E04
  1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.

  1. From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.

  1. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

    NOTICE:
    1. When separating the glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.
    2. To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.



    B106095E03
  1. Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.

    HINT:
    Matchmarks do not need to be placed if not reusing the glass.

  1. Cut through the adhesive by pulling the piano wire around the glass.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.

  1. Disengage the stoppers.

  1. Using suction cups, remove the glass.



25. CLEAN WINDSHIELD GLASS


B106080
  1. Using a scraper, remove the damaged stoppers, dams and adhesive sticking to the glass.

  1. Clean the outer edges of the glass with non-residue solvent.

    NOTICE:
    Do not touch the glass surface after cleaning it.
    Even if using new glass, clean it with non-residue solvent.



26. CLEAN VEHICLE BODY


B106081E05
  1. Clean and shape the contact surface of the vehicle body.

    1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

      NOTICE:
      Be careful not to damage the vehicle body.

  1. Clean the contact surface of the vehicle body with cleaner.

    HINT:
    Even if all the adhesive has been removed, clean the vehicle body.