Home › TRANSMISSION · A343E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0741    Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL)

for Preparation Click here


DESCRIPTION

The ECM uses the signals from the throttle position sensor, Mass Air Flow (MAF) meter, speed sensor (NC0), speed sensor (SP2) and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.
Then the ECM compares the engagement condition of the lock-up clutch with the lock-up schedule in the ECM memory to detect mechanical problems of the shift solenoid valve SL, valve body and torque converter assembly.

DTC Code
DTC Detection Condition
Trouble Area
P0741
Lock-up does not occur when driving in lock-up range (normal driving at 80 km/h (50 mph)), or lock-up remains ON in lock-up OFF range (2-trip detection logic)
  1. Shift solenoid valve SL remains open or closed
  2. Valve body is blocked
  3. Shift solenoid valve SL
  4. Torque converter assembly
  5. Automatic transmission (clutch, brake or gear etc.)
  6. ECM

MONITOR DESCRIPTION

Based on the signals from the throttle position sensor, MAF meter and crankshaft position sensor, the ECM sends a signal to the shift solenoid valve SL to regulate the hydraulic pressure and provide smoother gearshifts. The shift solenoid valve SL responds to commands from the ECM. The valve controls the lock-up relay valve to perform torque converter assembly lock-up and flexible lock-up functions.
The ECM compares the engine rpm (NE) signal with the input turbine speed signal to detect torque converter assembly lock-up. The ECM then compares the lock-up status with the lock-up schedule in the ECM memory. If the ECM does not detect lock-up at the appropriate time, it will conclude that there is a malfunction in shift solenoid valve SL. The ECM will illuminate the MIL and store the DTC.

INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0741)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the intelligent tester.
    Result 
    Result
    Proceed to
    Only P0741 is output
    A
    P0741 and other DTCs are output
    B

    HINT:
    If any other codes besides P0741 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.INSPECT SHIFT SOLENOID VALVE SL
C155226E06
  1. Remove the shift solenoid valve SL.

  1. Measure the resistance according to the value(s) in the table below.

    Tester Connection
    Condition
    Specified Condition
    Shift solenoid valve SL connector terminal - Shift solenoid valve SL body
    20°C (68°F)
    11 to 15 Ω

  1. Connect the battery's positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

  1. Check the operating noise of the solenoid valve.

    OK:
    Solenoid makes operating noise.



NG
REPLACE SHIFT SOLENOID VALVE SL
OK


3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly (Click here).

    OK:
    There are no foreign objects on any valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK


4.INSPECT TORQUE CONVERTER ASSEMBLY
  1. Check the torque converter assembly (Click here).

    OK:
    The torque converter assembly operates normally.



NG
REPLACE TORQUE CONVERTER ASSEMBLY
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY