Home › TRANSMISSION · A340F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > Park / Neutral Position Switch Circuit

for Preparation Click here


DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the TCM.

WIRING DIAGRAM


C122132E03


INSPECTION PROCEDURE

HINT:
Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

  1. Warm up the engine.
  2. Turn the ignition switch OFF.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch ON and push the tester main switch ON.
  5. Enter the following menus: Powertrain / ECT / Data List.
  6. Follow the instructions on the tester and read the Data List.

ECT 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Neutral Position SW Signal
PNP switch status/
ON or OFF
  1. Shift lever in P or N: ON
  2. Shift lever not in P or N: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (R Range)
PNP switch status/
ON or OFF
  1. Shift lever in R: ON
  2. Shift lever not in R: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (2 Range)
PNP switch status/
ON or OFF
  1. Shift lever in 2: ON
  2. Shift lever not in 2: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (L Range)
PNP switch status/
ON or OFF
  1. Shift lever in L: ON
  2. Shift lever not in L: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (D Range)
PNP switch status/
ON or OFF
  1. Shift lever in D: ON
  2. Shift lever not in D: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (3 Range)
PNP switch status/
ON or OFF
  1. Shift lever in 3: ON
  2. Shift lever not in 3: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

CAUTION:
In the table above, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
When the malfunction is found when the shift lever is on 3, start from *1. When the malfunction is found when the shift lever is not on 3, start from *2.

1.INSPECT PARK/NEUTRAL POSITION SWITCH*1


    G026080E06
  1. Disconnect the N1 park/neutral position switch connector.

  1. Measure the resistance of the park/neutral position switch when the shift lever is moved to each position.

    Standard resistance:
    Tester Connection
    Shift Lever Position
    Specified Condition
    4 (B) - 5 (L)
    P or N
    Below 1 Ω
    4 (B) - 5 (L)
    Not on P or N
    10 kΩ or higher
    1 (RL) - 2 (RB)
    R
    Below 1 Ω
    1 (RL) - 2 (RB)
    Not on R
    10 kΩ or higher
    2 (RB) - 7 (DL)
    D
    Below 1 Ω
    2 (RB) - 7 (DL)
    Not on D
    10 kΩ or higher
    2 (RB) - 3 (2L)
    2
    Below 1 Ω
    2 (RB) - 3 (2L)
    Not on 2
    10 kΩ or higher
    2 (RB) - 8 (LL)
    L
    Below 1 Ω
    2 (RB) - 8 (LL)
    Not on L
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH
OK


2.INSPECT SHIFT LOCK CONTROL ECU*2


    D029380E07
  1. Disconnect the S30 ECU connector.

  1. Measure the resistance of the ECU when the shift lever is moved to each position.

    Standard resistance:
    Tester Connection
    Shift Lever Position
    Specified Condition
    9 (NSSD) - 3 (AT3)
    D
    10 kΩor higher
    9 (NSSD) - 3 (AT3)
    3
    Below 1 Ω



NG
REPLACE SHIFT LOCK CONTROL ECU
OK


3.CHECK WIRE HARNESS (TCM - BATTERY)
G039243E15
  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connectors.

    Standard voltage:
    Tester Connection
    Shift Lever Position
    Specified Condition
    T19-12 (NSW) - Body ground
    P or N
    Below 1 V
    T19-12 (NSW) - Body ground
    Not in P or N
    10 to 14 V
    T36-9 (R) - Body ground
    R
    10 to 14 V*
    T36-9 (R) - Body ground
    Not on R
    Below 1 V
    T36-8 (D) - Body ground
    D or 3
    10 to 14 V
    T36-8 (D) - Body ground
    Not on D or 3
    Below 1 V
    T36-12 (3) - Body ground
    3
    10 to 14 V
    T36-12 (3) - Body ground
    Not on 3
    Below 1 V
    T36-11 (2) - Body ground
    2
    10 to 14 V
    T36-11 (2) - Body ground
    Not on 2
    Below 1 V
    T36-10 (L) - Body ground
    L
    10 to 14 V
    T36-10 (L) - Body ground
    Not on L
    Below 1 V

    HINT:
    *: The voltage will drop slightly due to the illumination of the back-up light.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE