Home › TRANSMISSION · A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P2769    Torque Converter Clutch Solenoid Circuit Low (Shift Solenoid Valve SL)

DTC    P2770    Torque Converter Clutch Solenoid Circuit High (Shift Solenoid Valve SL)

for Preparation Click here


DESCRIPTION

The shift solenoid valve SL is turned on and off by signals from the TCM to control the hydraulic pressure acting on the lock-up relay valve, which then controls the operation of the lock-up clutch.

DTC Code
DTC Detection Condition
Trouble Area
P2769
TCM detects short in shift solenoid valve SL circuit (once) when shift solenoid valve SL is operated (1-trip detection logic)
  1. Short in shift solenoid valve SL circuit
  2. Shift solenoid valve SL
  3. TCM
P2770
TCM detects open in shift solenoid valve SL circuit (once) when shift solenoid valve SL is not operated (1-trip detection logic)
  1. Open in shift solenoid valve SL circuit
  2. Shift solenoid valve SL
  3. TCM
Fail-safe function:
If the TCM detects a malfunction, it turns the shift solenoid valve SL off.

MONITOR DESCRIPTION

Torque converter lock-up is controlled by the TCM based on engine rpm, engine load, engine temperature, vehicle speed, transmission temperature, and shift position selection. The TCM determines the lock-up status of the torque converter by comparing the engine rpm (NE) to the input rpm (NC0). The TCM calculates the actual transmission gear by comparing the input rpm (NC0) to the output rpm (SP2). When conditions are appropriate, the TCM requests "lock-up" by applying control voltage to the shift solenoid valve SL. When the shift solenoid valve SL is opened, the shift solenoid valve SL applies pressure to the lock-up relay valve and locks the torque converter clutch. If the TCM detects an open or short in the shift solenoid valve SL circuit, the TCM interprets this as a fault in the shift solenoid valve SL or its circuit. The TCM will illuminate the MIL and store a DTC.

WIRING DIAGRAM


C237838E10


INSPECTION PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)


    C214964E11
  1. Disconnect the E1 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    7 (SL) - Body ground
    20°C (68°F)
    11 to 15 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 3
OK


2.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SL - TCM)


    C274533E43
  1. Disconnect the T19 TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T19-16 (SL) - Body ground
    20°C (68°F)
    11 to 15 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to TCM)



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE TCM 

3.INSPECT SHIFT SOLENOID VALVE SL


    C237973E01
  1. Remove shift solenoid valve SL.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid valve SL connector terminal - Shift solenoid valve SL body
    20°C (68°F)
    11 to 15 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) → Shift solenoid valve SL connector
    2. Battery negative (-) → Shift solenoid valve SL body
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve SL)


NG
REPLACE SHIFT SOLENOID VALVE SL
OK

REPLACE TRANSMISSION WIRE