Home › TRANSMISSION · A343E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 2TR-FBE)

DTC    P0712    Transmission Fluid Temperature Sensor "A" Circuit Low Input

DTC    P0713    Transmission Fluid Temperature Sensor "A" Circuit High Input

for Preparation Click here


DESCRIPTION

The Automatic Transmission Fluid (ATF) temperature sensor converts the ATF temperature into a resistance value which is input into the Engine Control Module (ECM).
The ECM applies a voltage to the temperature sensor through ECM terminal THOC.
The sensor resistance changes with the ATF temperature.
One terminal of the sensor is grounded so that the sensor resistance and voltage decrease as the temperature becomes higher.
The ECM calculates the ATF temperature based on the voltage signal.

DTC No.
DTC Detection Condition
Trouble Area
P0712
ATF temperature sensor resistance is less than 79 Ω for 0.5 sec. or more (1 trip detection logic)
  1. Short in ATF temperature sensor circuit
  2. ATF temperature sensor
  3. ECM
P0713
ATF temperature sensor resistance is more than 156 kΩ for 15 minutes or more after the engine starts (1 trip detection logic).
  1. Open in ATF temperature sensor circuit
  2. ATF temperature sensor
  3. ECM

MONITOR DESCRIPTION

The ATF temperature sensor converts ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature, and the ECM detects an open or short in the ATF temperature circuit. If the resistance value of the ATF temperature sensor is less than 79 Ω*1 or more than 156 kΩ*2, the ECM interprets this as a fault in the ATF sensor or wiring. The ECM will illuminate the MIL and store the DTC.

HINT:
  1. *1: 150°C (302°F) or more is indicated regardless of the actual ATF temperature.
  2. *2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.
  3. The ATF temperature can be checked on the intelligent tester display.


WIRING DIAGRAM


C214973E04


INSPECTION PROCEDURE

HINT:
Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch to ON and push the tester main switch on.
  5. Enter the following menus: Powertrain / Engine and ECT / Data List.
  6. Follow the instructions on the tester and read the Data List.

Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
A/T Oil Temperature 3
ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
  1. After stall speed test:
    Approximately 80°C (176°F)
  2. Equal to ambient temperature while engine is cold
If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or short circuited

NOTICE:
In the table above, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
  1. When DTC P0712 is output and the intelligent tester output is 150°C (302°F) or more, there is a short circuit.
  2. When DTC P0713 is output and the intelligent tester output is -40°C (-40°F), there is an open circuit.
    Check the temperature displayed on the tester in order to check if a malfunction exists.


Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
150°C (302°F) or more
Short circuit
1.INSPECT ATF TEMPERATURE SENSOR
C169604E01
  1. Disconnect the A38 ATF temperature sensor connector from the transmission.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    79 Ω to 156 kΩ
    1 - Body ground
    Always
    1 MΩ or higher
    2 - Body ground
    Always
    1 MΩ or higher

    HINT:
    If the resistance is not within the specified range for either of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

    ATF Temperature
    Specified Condition
    20°C (68°F)
    10.3 to 13.9 kΩ
    120°C (248°F)
    0.58 to 0.65 kΩ



NG
REPLACE ATF TEMPERATURE SENSOR
OK


2.CHECK WIRE HARNESS (ATF TEMPERATURE SENSOR - ECM)
C214975E03
  1. Disconnect the E20 and E21 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E20-2 (THOC) - E21-16 (E2)
    Always
    79 Ω to 156 kΩ
    E20-2 (THOC) - Body ground
    Always
    10 kΩ or higher
    E21-16 (E2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM