Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM (for Navigation Receiver Type)

REAR VIEW MONITOR SYSTEM (for Navigation Receiver Type) > TERMINALS OF ECU

for Preparation Click here



CHECK NAVIGATION RECEIVER ASSEMBLY

E234522E02

  1. Disconnect the N8 and N5 navigation receiver assembly connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specification
    N8-3 (ACC) - N8-7 (GND)
    GR - BR
    Accessory (ON)
    Ignition switch off
    Below 1 V
    Ignition switch ACC
    11 to 14 V
    N8-4 (B) - N8-7 (GND)
    L-Y - BR
    Battery
    Always
    11 to 14 V
    N8-7 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    N5-1 (IG) - N8-7 (GND)
    P - BR
    IG signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the N8 and N5 navigation receiver assembly connectors.

  4. Measure the voltage and waveform according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specification
    N5-2 (REV) - N8-7 (GND)
    R-Y - BR
    Reverse signal
    Ignition switch ON, shift lever in R
    7.5 to 14 V
    Ignition switch ON, shift lever not in R
    Below 1 V
    N6-7 (CA+) - N6-15 (CGND)
    B - Shielded
    Power source
    Ignition switch ON, shift lever in R
    5.5 to 7.05 V
    N6-8 (V+) - N6-16 (V-)
    W - R
    Display signal
    Ignition switch ON, shift lever in R
    Pulse generation (See waveform 1)
    Ignition switch ON, shift lever in R, screen blacked out by covering camera lens
    Pulse generation (See waveform 2)
    N6-15 (CGND) - Body ground
    Shielded - Body ground
    Shielding
    Always
    Below 1 V
    If the result is not as specified, the navigation receiver assembly may have a malfunction.



  5. E171712E24
  6. Using an oscilloscope, check the waveform.

    1. Waveform 1
      Measurement Condition 
      Item
      Content
      Terminal No. (Symbol)
      N6-8 (V+) - N6-16 (V-)
      Tool Setting
      0.2 V/DIV., 50 μs/DIV.
      Condition
      Ignition switch ON, shift lever in R

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

    2. Waveform 2
      Measurement Condition 
      Item
      Content
      Terminal No. (Symbol)
      N6-8 (V+) - N6-16 (V-)
      Tool Setting
      0.2 V/DIV., 50 μs/DIV.
      Condition
      Ignition switch ON, shift lever in R, screen blacked out by covering camera lens

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

      Text in Illustration 
      *a
      Waveform 1
      *b
      Waveform 2
      *c
      Synchronization Signal
      *d
      Video Waveform