INTAKE MANIFOLD > INSTALLATION |
| 1. INSTALL INTAKE MANIFOLD |
![]() |
Temporarily install a new gasket and the intake manifold with the 2 nuts and 4 bolts.
Tighten the 2 nuts and 4 bolts in the order shown in the illustration.
| 2. INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY |
Temporarily install the No. 2 nozzle leakage pipe with the 2 bolts.
Temporarily install a new gasket and the union bolt.
Tighten the 2 bolts and union bolt.
Connect the 3 fuel hoses.
| 3. INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY |
Temporarily install the No. 4 injection pipe with the union nuts.
Install the 2 bolts.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
| 4. INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY |
Temporarily install the No. 1, No. 2 and No. 3 injection pipes with the union nuts.
![]() |
Install the No. 2 and No. 3 injection pipe clamps with the bolt and 2 nuts as shown in the illustration.
| *1 | No. 1 Injection Pipe |
| *2 | No. 2 Injection Pipe Clamp |
| *3 | No. 3 Injection Pipe Clamp |
| *4 | Painted Mark |
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
| 5. INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY |
Install a new gasket and the electric EGR control valve.
Connect the EGR valve position sensor connector.
| 6. INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY |
![]() |
Install 2 new gaskets and the No. 1 EGR pipe with the 2 nuts and 2 bolts.
| *1 | Claw |
| 7. INSTALL INTAKE AIR CONNECTOR |
Install a new gasket and the intake air connector with the 2 nuts and bolt.
| 8. INSTALL NO. 2 INTAKE AIR CONNECTOR BRACKET |
Install the No. 2 intake air connector bracket with the 3 bolts.
| 9. INSTALL ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (for EGR) |
Install the electric vacuum regulating valve together with the bracket with the 2 bolts.
Connect the 2 vacuum hoses.
Connect the connector.
| 10. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE |
Install a new O-ring to the engine oil level dipstick guide.
Apply a small amount of clean engine oil to the O-ring.
Install the engine oil level dipstick guide with the bolt.
Install the injection pipe clamp with the bolt.
Install the engine oil level dipstick.
| 11. INSTALL MANIFOLD STAY |
![]() |
Install the manifold stay with the 2 bolts.
| 12. INSTALL DIESEL THROTTLE BODY ASSEMBLY |
| 13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 14. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Check if the engine starts.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak.*2
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
| 15. INSPECT FOR FUEL LEAK |
Check that there are no leaks from any part of the fuel system when the engine is stopped. If there is fuel leakage, repair or replace parts as necessary.
Start the engine and check that there are no leaks from any part of the fuel system. If there is fuel leakage, repair or replace parts as necessary.
Disconnect the return hose from the common rail.
Start the engine and check for fuel leaks from the return pipe.
If there is fuel leakage, replace the common rail.
Connect the intelligent tester to the DLC3.
Start the engine and turn the intelligent tester main switch on.
Select the Fuel Leak test from the Active Test mode on the intelligent tester.
If the intelligent tester is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.
Check that there are no leaks from any part of the fuel system.
Reconnect the return hose to the common rail.