INTAKE MANIFOLD (w/o Glow Plug Controller) > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE NO. 1 ENGINE UNDER COVER (w/ EGR Cooler) |
| 4. DRAIN ENGINE COOLANT (w/ EGR Cooler) |
![]() |
Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.
Loosen the cylinder block drain cock plug and the radiator drain cock plug.

| 5. REMOVE DIESEL THROTTLE BODY ASSEMBLY |
| 6. REMOVE MANIFOLD STAY (w/o EGR Cooler) |
![]() |
Remove the 2 bolts and manifold stay.
| 7. REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE (w/ EGR Cooler) |
Disconnect the 2 vacuum switching valve connectors and the 4 vacuum transmitting hoses.
![]() |
Remove the 2 bolts and manifold stay with vacuum switching valve.
| 8. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE |
Remove the engine oil level dipstick.
![]() |
Remove the bolt and injection pipe clamp.
Remove the bolt and engine oil level dipstick guide.
Remove the O-ring from the engine oil level dipstick guide.
| 9. REMOVE ELECTRIC EGR CONTROL VALVE WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler) |
| 10. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY (w/o EGR Cooler) |
w/ EGR Cooler:
![]() |
Remove the 2 nuts and No. 3 injection pipe clamp.
![]() |
Remove the 2 bolts and 2 No. 2 injection pipe clamps.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
w/o EGR Cooler:
![]() |
Remove the bolt and No. 2 injection pipe clamp.
Remove the 2 nuts and No. 3 injection pipe clamp.
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
| 11. REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/o EGR Cooler) |
![]() |
Remove the 3 bolts and No. 2 intake air connector bracket.
| 12. REMOVE INTAKE AIR CONNECTOR (w/o EGR Cooler) |
Remove the 2 nuts, bolt and intake air connector.
| 13. REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/o EGR Cooler) |
w/ EGR Cooler:
![]() |
Disconnect the connector.
![]() |
Disconnect the 4 vacuum hoses.
![]() |
Remove the 2 bolts and electric vacuum regulating valve with bracket.
w/o EGR Cooler:
![]() |
Disconnect the 2 connectors.
Disconnect the 3 vacuum hoses.
Remove the 2 bolts and electric vacuum regulating valve together with the bracket.
![]() |
Remove the screw and vacuum switching valve.
| 14. REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/o EGR Cooler) |
![]() |
Remove the 2 bolts, 2 nuts, No. 1 EGR pipe and 2 gaskets.
| 15. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/o EGR Cooler) |
![]() |
w/ EGR Cooler:
Remove the 2 bolts, electric EGR control valve and gasket.
w/o EGR Cooler:
Remove the electric EGR control valve and gasket.
| 16. REMOVE VACUUM CONTROL VALVE SET (w/ EGR Cooler) |
![]() |
Disconnect the 2 connectors and 3 vacuum hoses.
Remove the 2 bolts and vacuum control valve set.
| 17. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY |
w/ EGR Cooler:
![]() |
Remove the bolt and disconnect the injection pipe clamp.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
w/o EGR Cooler:
![]() |
Remove the 2 bolts and disconnect the 2 injection pipe clamps.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
| 18. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY |
Disconnect the 3 fuel hoses.
![]() |
Remove the union bolt, 3 bolts, No. 2 nozzle leakage pipe and gasket.
| 19. REMOVE NO. 3 INTERCOOLER SUPPORT BRACKET (w/ EGR Cooler) |
![]() |
Remove the bolt and No. 3 intercooler support bracket.
| 20. REMOVE INTAKE MANIFOLD INSULATOR (w/ EGR Cooler) |
![]() |
Remove the 2 bolts and intake manifold insulator from the intake manifold.
| 21. REMOVE INTAKE MANIFOLD |
![]() |
w/ EGR Cooler:
Disconnect the common rail sub-harness connector from the intake manifold.
w/o EGR Cooler:
Disconnect the vacuum hose and vacuum switching valve connector.
Remove the 4 bolts, 2 nuts, intake manifold and gasket.
