Home › ENGINE ยท 2KD-FTV › COOLING › WATER PUMP

WATER PUMP > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT FOR COOLANT LEAK

HINT:
  1. The sliding surface inside the engine water pump assembly is lubricated by engine coolant. As some engine coolant is discharged during normal operation, coolant residue (solids) may be found on the drain plug or the bottom of the engine water pump assembly. Engine coolant may leak if foreign matter enters the engine water pump assembly, however the sealing performance will recover when the foreign matter is pushed out or breaks into fine pieces.
  2. Before performing this inspection, check that there is no coolant leaking from any parts other than the engine water pump. If there are leaks, inspect those areas.
  3. Perform this inspection when the engine is cold.

  1. Visually check the engine water pump assembly.

    1. Check that engine coolant is not dripping from the engine water pump assembly.

      HINT:
      1. If engine coolant is dripping, replace the engine water pump assembly.
      2. If engine coolant is not dripping, perform the following check.



2. REMOVE FAN SHROUD


    A110387
  1. Remove the 3 bolts and oil reservoir.



    A252176
  1. Disconnect the No. 1 and No. 2 water by-pass hoses from the radiator.

  1. Remove the 2 bolts and radiator reservoir.

  1. Loosen the 4 nuts holding the fluid coupling with fan.

  1. Remove the fan and generator V belt (Click here).

  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling with fan, and then remove the fan shroud together with the fluid coupling with fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the engine water pump.



3. INSPECT ENGINE WATER PUMP ASSEMBLY


    A224945E01
  1. Visually check the water hole and air hole for coolant leakage.
    Text in Illustration 
    *1
    Water Hole
    *2
    Air Hole
    If leakage is found, replace the engine water pump assembly.

  1. Turn the pulley and check that the pump bearing moves smoothly and quietly.
    If the bearing moves roughly or noisily, replace the engine water pump assembly.



4. INSPECT FLUID COUPLING ASSEMBLY


    A112113
  1. Remove the 4 nuts and fan.



    A097646
  1. Check the fluid coupling for damage or silicon oil leaks. If necessary, replace the fluid coupling.

  1. Install the fan with the 4 nuts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



5. INSTALL FAN SHROUD
  1. Install the fan pulley to the engine water pump.

  1. Install the fan shroud together with the fluid coupling with fan between the radiator and engine component.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Install the fluid coupling with fan to the fan pulley with the 4 nuts.
    Tighten the nuts as much as possible by hand.



    A110385
  1. Attach the claws of the fan shroud to the radiator.

  1. Install the fan shroud with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the fan and generator V belt (Click here).

  1. Tighten the 4 nuts of the fluid coupling with fan.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

  1. Install the radiator reservoir with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the No. 1 and No. 2 water by-pass hoses to the radiator.

  1. Install the oil reservoir with the 3 bolts.

    Torque:
    4.5 N*m{ 46 kgf*cm , 40 in.*lbf }